Prepared HAL FW. Started reimplementing I2C.

fw_hal/Drivers/CMSIS/Device/ST/STM32L0xx/Include/stm32l0xx.h

@@ -0,0 +1,275 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx.h
+  * @author  MCD Application Team
+  * @brief   CMSIS Cortex-M0+ Device Peripheral Access Layer Header File. 
+  *          This file contains all the peripheral register's definitions, bits 
+  *          definitions and memory mapping for STM32L0xx devices.            
+  *            
+  *          The file is the unique include file that the application programmer
+  *          is using in the C source code, usually in main.c. This file contains:
+  *           - Configuration section that allows to select:
+  *              - The device used in the target application
+  *              - To use or not the peripheral's drivers in application code(i.e. 
+  *                code will be based on direct access to peripheral's registers 
+  *                rather than drivers API), this option is controlled by 
+  *                "#define USE_HAL_DRIVER"
+  *  
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************  
+  */ 
+
+/** @addtogroup CMSIS
+  * @{
+  */
+
+/** @addtogroup stm32l0xx
+  * @{
+  */
+    
+#ifndef __STM32L0xx_H
+#define __STM32L0xx_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif /* __cplusplus */
+   
+/** @addtogroup Library_configuration_section
+  * @{
+  */
+
+/**
+  * @brief STM32 Family
+  */
+#if !defined (STM32L0)
+#define STM32L0
+#endif /* STM32L0 */
+
+/* Uncomment the line below according to the target STM32 device used in your
+   application 
+  */
+
+#if !defined (STM32L010x4) && !defined (STM32L010x6) && !defined (STM32L010x8) && !defined (STM32L010xB) && \
+    !defined (STM32L011xx) && !defined (STM32L021xx) && \
+    !defined (STM32L031xx) && !defined (STM32L041xx) && \
+    !defined (STM32L051xx) && !defined (STM32L052xx) && !defined (STM32L053xx) && \
+    !defined (STM32L062xx) && !defined (STM32L063xx) && \
+    !defined (STM32L071xx) && !defined (STM32L072xx) && !defined (STM32L073xx) && \
+    !defined (STM32L081xx) && !defined (STM32L082xx) && !defined (STM32L083xx)
+  /* #define STM32L010x4 */   /*!< STM32L010K4, STM32L010F4 Devices                                                                                                                      */
+  /* #define STM32L010x6 */   /*!< STM32L010C6 Devices                                                                                                                                   */
+  /* #define STM32L010x8 */   /*!< STM32L010K8, STM32L010R8 Devices                                                                                                                      */
+  /* #define STM32L010xB */   /*!< STM32L010RB Devices                                                                                                                                   */
+  /* #define STM32L011xx */   /*!< STM32L031C6, STM32L031E6, STM32L031F6, STM32L031G6, STM32L031K6 Devices                                                                               */
+  /* #define STM32L021xx */   /*!< STM32L021D4, STM32L021F4, STM32L021G4, STM32L021K4 Devices                                                                                            */
+  /* #define STM32L031xx */   /*!< STM32L031C6, STM32L031E6, STM32L031F6, STM32L031G6, STM32L031K6 Devices                                                                               */
+  /* #define STM32L041xx */   /*!< STM32L041C6, STM32L041K6, STM32L041G6, STM32L041F6, STM32L041E6 Devices                                                                               */
+  /* #define STM32L051xx */   /*!< STM32L051K8, STM32L051C6, STM32L051C8, STM32L051R6, STM32L051R8, STM32L051K6, STM32L051T6, STM32L051T8 Devices                                        */
+  /* #define STM32L052xx */   /*!< STM32L052K6, STM32L052K8, STM32L052C6, STM32L052C8, STM32L052R6, STM32L052R8, STM32L052T6, STM32L052T8 Devices                                        */
+  /* #define STM32L053xx */   /*!< STM32L053C6, STM32L053C8, STM32L053R6, STM32L053R8 Devices                                                                                            */
+  /* #define STM32L062xx */   /*!< STM32L062K8 Devices                                                                                                                                   */
+  /* #define STM32L063xx */   /*!< STM32L063C8, STM32L063R8 Devices                                                                                                                      */
+  /* #define STM32L071xx */   /*!< STM32L071V8, STM32L071K8, STM32L071VB, STM32L071RB, STM32L071CB, STM32L071KB, STM32L071VZ, STM32L071RZ, STM32L071CZ, STM32L071KZ, STM32L071C8 Devices */
+  /* #define STM32L072xx */   /*!< STM32L072V8, STM32L072VB, STM32L072RB, STM32L072CB, STM32L072VZ, STM32L072RZ, STM32L072CZ, STM32L072KB, STM32L072KZ Devices                           */
+  /* #define STM32L073xx */   /*!< STM32L073V8, STM32L073VB, STM32L073RB, STM32L073VZ, STM32L073RZ, STM32L073CB, STM32L073CZ Devices                                                     */
+  /* #define STM32L081xx */   /*!< STM32L081CB, STM32L081CZ, STM32L081KZ Devices                                                                                                         */
+  /* #define STM32L082xx */   /*!< STM32L082KB, STM32L082KZ, STM32L082CZ Devices                                                                                                         */
+  /* #define STM32L083xx */   /*!< STM32L083V8, STM32L083VB, STM32L083RB, STM32L083VZ, STM32L083RZ, STM32L083CB, STM32L083CZ Devices                                                     */
+#endif
+   
+/*  Tip: To avoid modifying this file each time you need to switch between these
+        devices, you can define the device in your toolchain compiler preprocessor.
+  */
+#if !defined  (USE_HAL_DRIVER)
+/**
+ * @brief Comment the line below if you will not use the peripherals drivers.
+   In this case, these drivers will not be included and the application code will 
+   be based on direct access to peripherals registers 
+   */
+  /*#define USE_HAL_DRIVER */
+#endif /* USE_HAL_DRIVER */
+
+/**
+  * @brief CMSIS Device version number
+  */
+#define __STM32L0xx_CMSIS_VERSION_MAIN   (0x01) /*!< [31:24] main version */
+#define __STM32L0xx_CMSIS_VERSION_SUB1   (0x09) /*!< [23:16] sub1 version */
+#define __STM32L0xx_CMSIS_VERSION_SUB2   (0x02) /*!< [15:8]  sub2 version */
+#define __STM32L0xx_CMSIS_VERSION_RC     (0x00) /*!< [7:0]  release candidate */
+#define __STM32L0xx_CMSIS_VERSION        ((__STM32L0xx_CMSIS_VERSION_MAIN     << 24)\
+                                         |(__STM32L0xx_CMSIS_VERSION_SUB1 << 16)\
+                                         |(__STM32L0xx_CMSIS_VERSION_SUB2 << 8 )\
+                                         |(__STM32L0xx_CMSIS_VERSION_RC))
+                                             
+/**
+  * @}
+  */
+
+/** @addtogroup Device_Included
+  * @{
+  */
+#if defined(STM32L010xB)
+  #include "stm32l010xb.h"
+#elif defined(STM32L010x8)
+  #include "stm32l010x8.h"
+#elif defined(STM32L010x6)
+  #include "stm32l010x6.h"
+#elif defined(STM32L010x4)
+  #include "stm32l010x4.h"
+#elif defined(STM32L011xx)
+  #include "stm32l011xx.h"
+#elif defined(STM32L021xx)
+  #include "stm32l021xx.h"
+#elif defined(STM32L031xx)
+  #include "stm32l031xx.h"
+#elif defined(STM32L041xx)
+  #include "stm32l041xx.h"
+#elif defined(STM32L051xx)
+  #include "stm32l051xx.h"
+#elif defined(STM32L052xx)
+  #include "stm32l052xx.h"
+#elif defined(STM32L053xx)
+  #include "stm32l053xx.h"
+#elif defined(STM32L062xx)
+  #include "stm32l062xx.h"
+#elif defined(STM32L063xx)
+  #include "stm32l063xx.h"
+#elif defined(STM32L071xx)
+  #include "stm32l071xx.h"
+#elif defined(STM32L072xx)
+  #include "stm32l072xx.h"
+#elif defined(STM32L073xx)
+  #include "stm32l073xx.h"
+#elif defined(STM32L082xx)
+  #include "stm32l082xx.h"
+#elif defined(STM32L083xx)
+  #include "stm32l083xx.h"
+#elif defined(STM32L081xx)
+  #include "stm32l081xx.h"
+#else
+ #error "Please select first the target STM32L0xx device used in your application (in stm32l0xx.h file)"
+#endif
+
+/**
+  * @}
+  */
+
+/** @addtogroup Exported_types
+  * @{
+  */ 
+typedef enum 
+{
+  RESET = 0, 
+  SET = !RESET
+} FlagStatus, ITStatus;
+
+typedef enum 
+{
+  DISABLE = 0, 
+  ENABLE = !DISABLE
+} FunctionalState;
+#define IS_FUNCTIONAL_STATE(STATE) (((STATE) == DISABLE) || ((STATE) == ENABLE))
+
+typedef enum 
+{
+  SUCCESS = 0,
+  ERROR = !SUCCESS
+} ErrorStatus;
+
+/**
+  * @}
+  */
+
+
+/** @addtogroup Exported_macro
+  * @{
+  */
+#define SET_BIT(REG, BIT)     ((REG) |= (BIT))
+
+#define CLEAR_BIT(REG, BIT)   ((REG) &= ~(BIT))
+
+#define READ_BIT(REG, BIT)    ((REG) & (BIT))
+
+#define CLEAR_REG(REG)        ((REG) = (0x0))
+
+#define WRITE_REG(REG, VAL)   ((REG) = (VAL))
+
+#define READ_REG(REG)         ((REG))
+
+#define MODIFY_REG(REG, CLEARMASK, SETMASK)  WRITE_REG((REG), (((READ_REG(REG)) & (~(CLEARMASK))) | (SETMASK)))
+
+/* Use of interrupt control for register exclusive access */
+/* Atomic 32-bit register access macro to set one or several bits */
+#define ATOMIC_SET_BIT(REG, BIT)                             \
+  do {                                                       \
+    uint32_t primask;                                        \
+    primask = __get_PRIMASK();                               \
+    __set_PRIMASK(1);                                        \
+    SET_BIT((REG), (BIT));                                   \
+    __set_PRIMASK(primask);                                  \
+  } while(0)
+
+/* Atomic 32-bit register access macro to clear one or several bits */
+#define ATOMIC_CLEAR_BIT(REG, BIT)                           \
+  do {                                                       \
+    uint32_t primask;                                        \
+    primask = __get_PRIMASK();                               \
+    __set_PRIMASK(1);                                        \
+    CLEAR_BIT((REG), (BIT));                                 \
+    __set_PRIMASK(primask);                                  \
+  } while(0)
+
+/* Atomic 32-bit register access macro to clear and set one or several bits */
+#define ATOMIC_MODIFY_REG(REG, CLEARMSK, SETMASK)            \
+  do {                                                       \
+    uint32_t primask;                                        \
+    primask = __get_PRIMASK();                               \
+    __set_PRIMASK(1);                                        \
+    MODIFY_REG((REG), (CLEARMSK), (SETMASK));                \
+    __set_PRIMASK(primask);                                  \
+  } while(0)
+
+/* Atomic 16-bit register access macro to set one or several bits */
+#define ATOMIC_SETH_BIT(REG, BIT) ATOMIC_SET_BIT(REG, BIT)                                   \
+
+/* Atomic 16-bit register access macro to clear one or several bits */
+#define ATOMIC_CLEARH_BIT(REG, BIT) ATOMIC_CLEAR_BIT(REG, BIT)                               \
+
+/* Atomic 16-bit register access macro to clear and set one or several bits */
+#define ATOMIC_MODIFYH_REG(REG, CLEARMSK, SETMASK) ATOMIC_MODIFY_REG(REG, CLEARMSK, SETMASK) \
+
+/**
+  * @}
+  */
+
+#if defined (USE_HAL_DRIVER)
+ #include "stm32l0xx_hal.h"
+#endif /* USE_HAL_DRIVER */
+
+#ifdef __cplusplus
+}
+#endif /* __cplusplus */
+
+#endif /* __STM32L0xx_H */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/CMSIS/Device/ST/STM32L0xx/Include/system_stm32l0xx.h

@@ -0,0 +1,109 @@
+/**
+  ******************************************************************************
+  * @file    system_stm32l0xx.h
+  * @author  MCD Application Team
+  * @brief   CMSIS Cortex-M0+ Device Peripheral Access Layer System Header File.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/** @addtogroup CMSIS
+  * @{
+  */
+
+/** @addtogroup stm32l0xx_system
+  * @{
+  */  
+  
+/**
+  * @brief Define to prevent recursive inclusion
+  */
+#ifndef __SYSTEM_STM32L0XX_H
+#define __SYSTEM_STM32L0XX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif 
+
+/** @addtogroup STM32L0xx_System_Includes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+
+/** @addtogroup STM32L0xx_System_Exported_types
+  * @{
+  */
+  /* This variable is updated in three ways:
+      1) by calling CMSIS function SystemCoreClockUpdate()
+      2) by calling HAL API function HAL_RCC_GetSysClockFreq()
+      3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency 
+         Note: If you use this function to configure the system clock; then there
+               is no need to call the 2 first functions listed above, since SystemCoreClock
+               variable is updated automatically.
+  */
+extern uint32_t SystemCoreClock;          /*!< System Clock Frequency (Core Clock) */
+/*
+*/
+extern const uint8_t AHBPrescTable[16];   /*!< AHB prescalers table values */
+extern const uint8_t APBPrescTable[8];    /*!< APB prescalers table values */
+extern const uint8_t PLLMulTable[9];      /*!< PLL multipiers table values */
+
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32L0xx_System_Exported_Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32L0xx_System_Exported_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32L0xx_System_Exported_Functions
+  * @{
+  */
+  
+extern void SystemInit(void);
+extern void SystemCoreClockUpdate(void);
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /*__SYSTEM_STM32L0XX_H */
+
+/**
+  * @}
+  */
+  
+/**
+  * @}
+  */  
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/CMSIS/Include/cmsis_armcc.h

@@ -0,0 +1,865 @@
+/**************************************************************************//**
+ * @file     cmsis_armcc.h
+ * @brief    CMSIS compiler ARMCC (Arm Compiler 5) header file
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_ARMCC_H
+#define __CMSIS_ARMCC_H
+
+
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 400677)
+  #error "Please use Arm Compiler Toolchain V4.0.677 or later!"
+#endif
+
+/* CMSIS compiler control architecture macros */
+#if ((defined (__TARGET_ARCH_6_M  ) && (__TARGET_ARCH_6_M   == 1)) || \
+     (defined (__TARGET_ARCH_6S_M ) && (__TARGET_ARCH_6S_M  == 1))   )
+  #define __ARM_ARCH_6M__           1
+#endif
+
+#if (defined (__TARGET_ARCH_7_M ) && (__TARGET_ARCH_7_M  == 1))
+  #define __ARM_ARCH_7M__           1
+#endif
+
+#if (defined (__TARGET_ARCH_7E_M) && (__TARGET_ARCH_7E_M == 1))
+  #define __ARM_ARCH_7EM__          1
+#endif
+
+  /* __ARM_ARCH_8M_BASE__  not applicable */
+  /* __ARM_ARCH_8M_MAIN__  not applicable */
+
+
+/* CMSIS compiler specific defines */
+#ifndef   __ASM
+  #define __ASM                                  __asm
+#endif
+#ifndef   __INLINE
+  #define __INLINE                               __inline
+#endif
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE                        static __inline
+#endif
+#ifndef   __STATIC_FORCEINLINE                 
+  #define __STATIC_FORCEINLINE                   static __forceinline
+#endif           
+#ifndef   __NO_RETURN
+  #define __NO_RETURN                            __declspec(noreturn)
+#endif
+#ifndef   __USED
+  #define __USED                                 __attribute__((used))
+#endif
+#ifndef   __WEAK
+  #define __WEAK                                 __attribute__((weak))
+#endif
+#ifndef   __PACKED
+  #define __PACKED                               __attribute__((packed))
+#endif
+#ifndef   __PACKED_STRUCT
+  #define __PACKED_STRUCT                        __packed struct
+#endif
+#ifndef   __PACKED_UNION
+  #define __PACKED_UNION                         __packed union
+#endif
+#ifndef   __UNALIGNED_UINT32        /* deprecated */
+  #define __UNALIGNED_UINT32(x)                  (*((__packed uint32_t *)(x)))
+#endif
+#ifndef   __UNALIGNED_UINT16_WRITE
+  #define __UNALIGNED_UINT16_WRITE(addr, val)    ((*((__packed uint16_t *)(addr))) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT16_READ
+  #define __UNALIGNED_UINT16_READ(addr)          (*((const __packed uint16_t *)(addr)))
+#endif
+#ifndef   __UNALIGNED_UINT32_WRITE
+  #define __UNALIGNED_UINT32_WRITE(addr, val)    ((*((__packed uint32_t *)(addr))) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT32_READ
+  #define __UNALIGNED_UINT32_READ(addr)          (*((const __packed uint32_t *)(addr)))
+#endif
+#ifndef   __ALIGNED
+  #define __ALIGNED(x)                           __attribute__((aligned(x)))
+#endif
+#ifndef   __RESTRICT
+  #define __RESTRICT                             __restrict
+#endif
+
+/* ###########################  Core Function Access  ########################### */
+/** \ingroup  CMSIS_Core_FunctionInterface
+    \defgroup CMSIS_Core_RegAccFunctions CMSIS Core Register Access Functions
+  @{
+ */
+
+/**
+  \brief   Enable IRQ Interrupts
+  \details Enables IRQ interrupts by clearing the I-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+/* intrinsic void __enable_irq();     */
+
+
+/**
+  \brief   Disable IRQ Interrupts
+  \details Disables IRQ interrupts by setting the I-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+/* intrinsic void __disable_irq();    */
+
+/**
+  \brief   Get Control Register
+  \details Returns the content of the Control Register.
+  \return               Control Register value
+ */
+__STATIC_INLINE uint32_t __get_CONTROL(void)
+{
+  register uint32_t __regControl         __ASM("control");
+  return(__regControl);
+}
+
+
+/**
+  \brief   Set Control Register
+  \details Writes the given value to the Control Register.
+  \param [in]    control  Control Register value to set
+ */
+__STATIC_INLINE void __set_CONTROL(uint32_t control)
+{
+  register uint32_t __regControl         __ASM("control");
+  __regControl = control;
+}
+
+
+/**
+  \brief   Get IPSR Register
+  \details Returns the content of the IPSR Register.
+  \return               IPSR Register value
+ */
+__STATIC_INLINE uint32_t __get_IPSR(void)
+{
+  register uint32_t __regIPSR          __ASM("ipsr");
+  return(__regIPSR);
+}
+
+
+/**
+  \brief   Get APSR Register
+  \details Returns the content of the APSR Register.
+  \return               APSR Register value
+ */
+__STATIC_INLINE uint32_t __get_APSR(void)
+{
+  register uint32_t __regAPSR          __ASM("apsr");
+  return(__regAPSR);
+}
+
+
+/**
+  \brief   Get xPSR Register
+  \details Returns the content of the xPSR Register.
+  \return               xPSR Register value
+ */
+__STATIC_INLINE uint32_t __get_xPSR(void)
+{
+  register uint32_t __regXPSR          __ASM("xpsr");
+  return(__regXPSR);
+}
+
+
+/**
+  \brief   Get Process Stack Pointer
+  \details Returns the current value of the Process Stack Pointer (PSP).
+  \return               PSP Register value
+ */
+__STATIC_INLINE uint32_t __get_PSP(void)
+{
+  register uint32_t __regProcessStackPointer  __ASM("psp");
+  return(__regProcessStackPointer);
+}
+
+
+/**
+  \brief   Set Process Stack Pointer
+  \details Assigns the given value to the Process Stack Pointer (PSP).
+  \param [in]    topOfProcStack  Process Stack Pointer value to set
+ */
+__STATIC_INLINE void __set_PSP(uint32_t topOfProcStack)
+{
+  register uint32_t __regProcessStackPointer  __ASM("psp");
+  __regProcessStackPointer = topOfProcStack;
+}
+
+
+/**
+  \brief   Get Main Stack Pointer
+  \details Returns the current value of the Main Stack Pointer (MSP).
+  \return               MSP Register value
+ */
+__STATIC_INLINE uint32_t __get_MSP(void)
+{
+  register uint32_t __regMainStackPointer     __ASM("msp");
+  return(__regMainStackPointer);
+}
+
+
+/**
+  \brief   Set Main Stack Pointer
+  \details Assigns the given value to the Main Stack Pointer (MSP).
+  \param [in]    topOfMainStack  Main Stack Pointer value to set
+ */
+__STATIC_INLINE void __set_MSP(uint32_t topOfMainStack)
+{
+  register uint32_t __regMainStackPointer     __ASM("msp");
+  __regMainStackPointer = topOfMainStack;
+}
+
+
+/**
+  \brief   Get Priority Mask
+  \details Returns the current state of the priority mask bit from the Priority Mask Register.
+  \return               Priority Mask value
+ */
+__STATIC_INLINE uint32_t __get_PRIMASK(void)
+{
+  register uint32_t __regPriMask         __ASM("primask");
+  return(__regPriMask);
+}
+
+
+/**
+  \brief   Set Priority Mask
+  \details Assigns the given value to the Priority Mask Register.
+  \param [in]    priMask  Priority Mask
+ */
+__STATIC_INLINE void __set_PRIMASK(uint32_t priMask)
+{
+  register uint32_t __regPriMask         __ASM("primask");
+  __regPriMask = (priMask);
+}
+
+
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+/**
+  \brief   Enable FIQ
+  \details Enables FIQ interrupts by clearing the F-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+#define __enable_fault_irq                __enable_fiq
+
+
+/**
+  \brief   Disable FIQ
+  \details Disables FIQ interrupts by setting the F-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+#define __disable_fault_irq               __disable_fiq
+
+
+/**
+  \brief   Get Base Priority
+  \details Returns the current value of the Base Priority register.
+  \return               Base Priority register value
+ */
+__STATIC_INLINE uint32_t  __get_BASEPRI(void)
+{
+  register uint32_t __regBasePri         __ASM("basepri");
+  return(__regBasePri);
+}
+
+
+/**
+  \brief   Set Base Priority
+  \details Assigns the given value to the Base Priority register.
+  \param [in]    basePri  Base Priority value to set
+ */
+__STATIC_INLINE void __set_BASEPRI(uint32_t basePri)
+{
+  register uint32_t __regBasePri         __ASM("basepri");
+  __regBasePri = (basePri & 0xFFU);
+}
+
+
+/**
+  \brief   Set Base Priority with condition
+  \details Assigns the given value to the Base Priority register only if BASEPRI masking is disabled,
+           or the new value increases the BASEPRI priority level.
+  \param [in]    basePri  Base Priority value to set
+ */
+__STATIC_INLINE void __set_BASEPRI_MAX(uint32_t basePri)
+{
+  register uint32_t __regBasePriMax      __ASM("basepri_max");
+  __regBasePriMax = (basePri & 0xFFU);
+}
+
+
+/**
+  \brief   Get Fault Mask
+  \details Returns the current value of the Fault Mask register.
+  \return               Fault Mask register value
+ */
+__STATIC_INLINE uint32_t __get_FAULTMASK(void)
+{
+  register uint32_t __regFaultMask       __ASM("faultmask");
+  return(__regFaultMask);
+}
+
+
+/**
+  \brief   Set Fault Mask
+  \details Assigns the given value to the Fault Mask register.
+  \param [in]    faultMask  Fault Mask value to set
+ */
+__STATIC_INLINE void __set_FAULTMASK(uint32_t faultMask)
+{
+  register uint32_t __regFaultMask       __ASM("faultmask");
+  __regFaultMask = (faultMask & (uint32_t)1U);
+}
+
+#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+
+/**
+  \brief   Get FPSCR
+  \details Returns the current value of the Floating Point Status/Control register.
+  \return               Floating Point Status/Control register value
+ */
+__STATIC_INLINE uint32_t __get_FPSCR(void)
+{
+#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+     (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  register uint32_t __regfpscr         __ASM("fpscr");
+  return(__regfpscr);
+#else
+   return(0U);
+#endif
+}
+
+
+/**
+  \brief   Set FPSCR
+  \details Assigns the given value to the Floating Point Status/Control register.
+  \param [in]    fpscr  Floating Point Status/Control value to set
+ */
+__STATIC_INLINE void __set_FPSCR(uint32_t fpscr)
+{
+#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+     (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  register uint32_t __regfpscr         __ASM("fpscr");
+  __regfpscr = (fpscr);
+#else
+  (void)fpscr;
+#endif
+}
+
+
+/*@} end of CMSIS_Core_RegAccFunctions */
+
+
+/* ##########################  Core Instruction Access  ######################### */
+/** \defgroup CMSIS_Core_InstructionInterface CMSIS Core Instruction Interface
+  Access to dedicated instructions
+  @{
+*/
+
+/**
+  \brief   No Operation
+  \details No Operation does nothing. This instruction can be used for code alignment purposes.
+ */
+#define __NOP                             __nop
+
+
+/**
+  \brief   Wait For Interrupt
+  \details Wait For Interrupt is a hint instruction that suspends execution until one of a number of events occurs.
+ */
+#define __WFI                             __wfi
+
+
+/**
+  \brief   Wait For Event
+  \details Wait For Event is a hint instruction that permits the processor to enter
+           a low-power state until one of a number of events occurs.
+ */
+#define __WFE                             __wfe
+
+
+/**
+  \brief   Send Event
+  \details Send Event is a hint instruction. It causes an event to be signaled to the CPU.
+ */
+#define __SEV                             __sev
+
+
+/**
+  \brief   Instruction Synchronization Barrier
+  \details Instruction Synchronization Barrier flushes the pipeline in the processor,
+           so that all instructions following the ISB are fetched from cache or memory,
+           after the instruction has been completed.
+ */
+#define __ISB() do {\
+                   __schedule_barrier();\
+                   __isb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Synchronization Barrier
+  \details Acts as a special kind of Data Memory Barrier.
+           It completes when all explicit memory accesses before this instruction complete.
+ */
+#define __DSB() do {\
+                   __schedule_barrier();\
+                   __dsb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Memory Barrier
+  \details Ensures the apparent order of the explicit memory operations before
+           and after the instruction, without ensuring their completion.
+ */
+#define __DMB() do {\
+                   __schedule_barrier();\
+                   __dmb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+                  
+/**
+  \brief   Reverse byte order (32 bit)
+  \details Reverses the byte order in unsigned integer value. For example, 0x12345678 becomes 0x78563412.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#define __REV                             __rev
+
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order within each halfword of a word. For example, 0x12345678 becomes 0x34127856.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".rev16_text"))) __STATIC_INLINE __ASM uint32_t __REV16(uint32_t value)
+{
+  rev16 r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order in a 16-bit value and returns the signed 16-bit result. For example, 0x0080 becomes 0x8000.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".revsh_text"))) __STATIC_INLINE __ASM int16_t __REVSH(int16_t value)
+{
+  revsh r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   Rotate Right in unsigned value (32 bit)
+  \details Rotate Right (immediate) provides the value of the contents of a register rotated by a variable number of bits.
+  \param [in]    op1  Value to rotate
+  \param [in]    op2  Number of Bits to rotate
+  \return               Rotated value
+ */
+#define __ROR                             __ror
+
+
+/**
+  \brief   Breakpoint
+  \details Causes the processor to enter Debug state.
+           Debug tools can use this to investigate system state when the instruction at a particular address is reached.
+  \param [in]    value  is ignored by the processor.
+                 If required, a debugger can use it to store additional information about the breakpoint.
+ */
+#define __BKPT(value)                       __breakpoint(value)
+
+
+/**
+  \brief   Reverse bit order of value
+  \details Reverses the bit order of the given value.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+  #define __RBIT                          __rbit
+#else
+__attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value)
+{
+  uint32_t result;
+  uint32_t s = (4U /*sizeof(v)*/ * 8U) - 1U; /* extra shift needed at end */
+
+  result = value;                      /* r will be reversed bits of v; first get LSB of v */
+  for (value >>= 1U; value != 0U; value >>= 1U)
+  {
+    result <<= 1U;
+    result |= value & 1U;
+    s--;
+  }
+  result <<= s;                        /* shift when v's highest bits are zero */
+  return result;
+}
+#endif
+
+
+/**
+  \brief   Count leading zeros
+  \details Counts the number of leading zeros of a data value.
+  \param [in]  value  Value to count the leading zeros
+  \return             number of leading zeros in value
+ */
+#define __CLZ                             __clz
+
+
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+/**
+  \brief   LDR Exclusive (8 bit)
+  \details Executes a exclusive LDR instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXB(ptr)                                                        ((uint8_t ) __ldrex(ptr))
+#else
+  #define __LDREXB(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint8_t ) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   LDR Exclusive (16 bit)
+  \details Executes a exclusive LDR instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXH(ptr)                                                        ((uint16_t) __ldrex(ptr))
+#else
+  #define __LDREXH(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint16_t) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   LDR Exclusive (32 bit)
+  \details Executes a exclusive LDR instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXW(ptr)                                                        ((uint32_t ) __ldrex(ptr))
+#else
+  #define __LDREXW(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint32_t ) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (8 bit)
+  \details Executes a exclusive STR instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXB(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXB(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (16 bit)
+  \details Executes a exclusive STR instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXH(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXH(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (32 bit)
+  \details Executes a exclusive STR instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXW(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXW(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   Remove the exclusive lock
+  \details Removes the exclusive lock which is created by LDREX.
+ */
+#define __CLREX                           __clrex
+
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+#define __SSAT                            __ssat
+
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+#define __USAT                            __usat
+
+
+/**
+  \brief   Rotate Right with Extend (32 bit)
+  \details Moves each bit of a bitstring right by one bit.
+           The carry input is shifted in at the left end of the bitstring.
+  \param [in]    value  Value to rotate
+  \return               Rotated value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".rrx_text"))) __STATIC_INLINE __ASM uint32_t __RRX(uint32_t value)
+{
+  rrx r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   LDRT Unprivileged (8 bit)
+  \details Executes a Unprivileged LDRT instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+#define __LDRBT(ptr)                      ((uint8_t )  __ldrt(ptr))
+
+
+/**
+  \brief   LDRT Unprivileged (16 bit)
+  \details Executes a Unprivileged LDRT instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+#define __LDRHT(ptr)                      ((uint16_t)  __ldrt(ptr))
+
+
+/**
+  \brief   LDRT Unprivileged (32 bit)
+  \details Executes a Unprivileged LDRT instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+#define __LDRT(ptr)                       ((uint32_t ) __ldrt(ptr))
+
+
+/**
+  \brief   STRT Unprivileged (8 bit)
+  \details Executes a Unprivileged STRT instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRBT(value, ptr)               __strt(value, ptr)
+
+
+/**
+  \brief   STRT Unprivileged (16 bit)
+  \details Executes a Unprivileged STRT instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRHT(value, ptr)               __strt(value, ptr)
+
+
+/**
+  \brief   STRT Unprivileged (32 bit)
+  \details Executes a Unprivileged STRT instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRT(value, ptr)                __strt(value, ptr)
+
+#else  /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+__attribute__((always_inline)) __STATIC_INLINE int32_t __SSAT(int32_t val, uint32_t sat)
+{
+  if ((sat >= 1U) && (sat <= 32U))
+  {
+    const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U);
+    const int32_t min = -1 - max ;
+    if (val > max)
+    {
+      return max;
+    }
+    else if (val < min)
+    {
+      return min;
+    }
+  }
+  return val;
+}
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+__attribute__((always_inline)) __STATIC_INLINE uint32_t __USAT(int32_t val, uint32_t sat)
+{
+  if (sat <= 31U)
+  {
+    const uint32_t max = ((1U << sat) - 1U);
+    if (val > (int32_t)max)
+    {
+      return max;
+    }
+    else if (val < 0)
+    {
+      return 0U;
+    }
+  }
+  return (uint32_t)val;
+}
+
+#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+/*@}*/ /* end of group CMSIS_Core_InstructionInterface */
+
+
+/* ###################  Compiler specific Intrinsics  ########################### */
+/** \defgroup CMSIS_SIMD_intrinsics CMSIS SIMD Intrinsics
+  Access to dedicated SIMD instructions
+  @{
+*/
+
+#if ((defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+#define __SADD8                           __sadd8
+#define __QADD8                           __qadd8
+#define __SHADD8                          __shadd8
+#define __UADD8                           __uadd8
+#define __UQADD8                          __uqadd8
+#define __UHADD8                          __uhadd8
+#define __SSUB8                           __ssub8
+#define __QSUB8                           __qsub8
+#define __SHSUB8                          __shsub8
+#define __USUB8                           __usub8
+#define __UQSUB8                          __uqsub8
+#define __UHSUB8                          __uhsub8
+#define __SADD16                          __sadd16
+#define __QADD16                          __qadd16
+#define __SHADD16                         __shadd16
+#define __UADD16                          __uadd16
+#define __UQADD16                         __uqadd16
+#define __UHADD16                         __uhadd16
+#define __SSUB16                          __ssub16
+#define __QSUB16                          __qsub16
+#define __SHSUB16                         __shsub16
+#define __USUB16                          __usub16
+#define __UQSUB16                         __uqsub16
+#define __UHSUB16                         __uhsub16
+#define __SASX                            __sasx
+#define __QASX                            __qasx
+#define __SHASX                           __shasx
+#define __UASX                            __uasx
+#define __UQASX                           __uqasx
+#define __UHASX                           __uhasx
+#define __SSAX                            __ssax
+#define __QSAX                            __qsax
+#define __SHSAX                           __shsax
+#define __USAX                            __usax
+#define __UQSAX                           __uqsax
+#define __UHSAX                           __uhsax
+#define __USAD8                           __usad8
+#define __USADA8                          __usada8
+#define __SSAT16                          __ssat16
+#define __USAT16                          __usat16
+#define __UXTB16                          __uxtb16
+#define __UXTAB16                         __uxtab16
+#define __SXTB16                          __sxtb16
+#define __SXTAB16                         __sxtab16
+#define __SMUAD                           __smuad
+#define __SMUADX                          __smuadx
+#define __SMLAD                           __smlad
+#define __SMLADX                          __smladx
+#define __SMLALD                          __smlald
+#define __SMLALDX                         __smlaldx
+#define __SMUSD                           __smusd
+#define __SMUSDX                          __smusdx
+#define __SMLSD                           __smlsd
+#define __SMLSDX                          __smlsdx
+#define __SMLSLD                          __smlsld
+#define __SMLSLDX                         __smlsldx
+#define __SEL                             __sel
+#define __QADD                            __qadd
+#define __QSUB                            __qsub
+
+#define __PKHBT(ARG1,ARG2,ARG3)          ( ((((uint32_t)(ARG1))          ) & 0x0000FFFFUL) |  \
+                                           ((((uint32_t)(ARG2)) << (ARG3)) & 0xFFFF0000UL)  )
+
+#define __PKHTB(ARG1,ARG2,ARG3)          ( ((((uint32_t)(ARG1))          ) & 0xFFFF0000UL) |  \
+                                           ((((uint32_t)(ARG2)) >> (ARG3)) & 0x0000FFFFUL)  )
+
+#define __SMMLA(ARG1,ARG2,ARG3)          ( (int32_t)((((int64_t)(ARG1) * (ARG2)) + \
+                                                      ((int64_t)(ARG3) << 32U)     ) >> 32U))
+
+#endif /* ((defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+/*@} end of group CMSIS_SIMD_intrinsics */
+
+
+#endif /* __CMSIS_ARMCC_H */

fw_hal/Drivers/CMSIS/Include/cmsis_compiler.h

@@ -0,0 +1,266 @@
+/**************************************************************************//**
+ * @file     cmsis_compiler.h
+ * @brief    CMSIS compiler generic header file
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_COMPILER_H
+#define __CMSIS_COMPILER_H
+
+#include <stdint.h>
+
+/*
+ * Arm Compiler 4/5
+ */
+#if   defined ( __CC_ARM )
+  #include "cmsis_armcc.h"
+
+
+/*
+ * Arm Compiler 6 (armclang)
+ */
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #include "cmsis_armclang.h"
+
+
+/*
+ * GNU Compiler
+ */
+#elif defined ( __GNUC__ )
+  #include "cmsis_gcc.h"
+
+
+/*
+ * IAR Compiler
+ */
+#elif defined ( __ICCARM__ )
+  #include <cmsis_iccarm.h>
+
+
+/*
+ * TI Arm Compiler
+ */
+#elif defined ( __TI_ARM__ )
+  #include <cmsis_ccs.h>
+
+  #ifndef   __ASM
+    #define __ASM                                  __asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    #define __NO_RETURN                            __attribute__((noreturn))
+  #endif
+  #ifndef   __USED
+    #define __USED                                 __attribute__((used))
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __attribute__((weak))
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               __attribute__((packed))
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        struct __attribute__((packed))
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         union __attribute__((packed))
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    struct __attribute__((packed)) T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void*)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #define __ALIGNED(x)                           __attribute__((aligned(x)))
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+/*
+ * TASKING Compiler
+ */
+#elif defined ( __TASKING__ )
+  /*
+   * The CMSIS functions have been implemented as intrinsics in the compiler.
+   * Please use "carm -?i" to get an up to date list of all intrinsics,
+   * Including the CMSIS ones.
+   */
+
+  #ifndef   __ASM
+    #define __ASM                                  __asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    #define __NO_RETURN                            __attribute__((noreturn))
+  #endif
+  #ifndef   __USED
+    #define __USED                                 __attribute__((used))
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __attribute__((weak))
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               __packed__
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        struct __packed__
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         union __packed__
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    struct __packed__ T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #define __ALIGNED(x)              __align(x)
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+/*
+ * COSMIC Compiler
+ */
+#elif defined ( __CSMC__ )
+   #include <cmsis_csm.h>
+
+ #ifndef   __ASM
+    #define __ASM                                  _asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    // NO RETURN is automatically detected hence no warning here
+    #define __NO_RETURN
+  #endif
+  #ifndef   __USED
+    #warning No compiler specific solution for __USED. __USED is ignored.
+    #define __USED
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __weak
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               @packed
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        @packed struct
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         @packed union
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    @packed struct T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #warning No compiler specific solution for __ALIGNED. __ALIGNED is ignored.
+    #define __ALIGNED(x)
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+#else
+  #error Unknown compiler.
+#endif
+
+
+#endif /* __CMSIS_COMPILER_H */
+

fw_hal/Drivers/CMSIS/Include/cmsis_iccarm.h

@@ -0,0 +1,935 @@
+/**************************************************************************//**
+ * @file     cmsis_iccarm.h
+ * @brief    CMSIS compiler ICCARM (IAR Compiler for Arm) header file
+ * @version  V5.0.7
+ * @date     19. June 2018
+ ******************************************************************************/
+
+//------------------------------------------------------------------------------
+//
+// Copyright (c) 2017-2018 IAR Systems
+//
+// Licensed under the Apache License, Version 2.0 (the "License")
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//     http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+//
+//------------------------------------------------------------------------------
+
+
+#ifndef __CMSIS_ICCARM_H__
+#define __CMSIS_ICCARM_H__
+
+#ifndef __ICCARM__
+  #error This file should only be compiled by ICCARM
+#endif
+
+#pragma system_include
+
+#define __IAR_FT _Pragma("inline=forced") __intrinsic
+
+#if (__VER__ >= 8000000)
+  #define __ICCARM_V8 1
+#else
+  #define __ICCARM_V8 0
+#endif
+
+#ifndef __ALIGNED
+  #if __ICCARM_V8
+    #define __ALIGNED(x) __attribute__((aligned(x)))
+  #elif (__VER__ >= 7080000)
+    /* Needs IAR language extensions */
+    #define __ALIGNED(x) __attribute__((aligned(x)))
+  #else
+    #warning No compiler specific solution for __ALIGNED.__ALIGNED is ignored.
+    #define __ALIGNED(x)
+  #endif
+#endif
+
+
+/* Define compiler macros for CPU architecture, used in CMSIS 5.
+ */
+#if __ARM_ARCH_6M__ || __ARM_ARCH_7M__ || __ARM_ARCH_7EM__ || __ARM_ARCH_8M_BASE__ || __ARM_ARCH_8M_MAIN__
+/* Macros already defined */
+#else
+  #if defined(__ARM8M_MAINLINE__) || defined(__ARM8EM_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #elif defined(__ARM8M_BASELINE__)
+    #define __ARM_ARCH_8M_BASE__ 1
+  #elif defined(__ARM_ARCH_PROFILE) && __ARM_ARCH_PROFILE == 'M'
+    #if __ARM_ARCH == 6
+      #define __ARM_ARCH_6M__ 1
+    #elif __ARM_ARCH == 7
+      #if __ARM_FEATURE_DSP
+        #define __ARM_ARCH_7EM__ 1
+      #else
+        #define __ARM_ARCH_7M__ 1
+      #endif
+    #endif /* __ARM_ARCH */
+  #endif /* __ARM_ARCH_PROFILE == 'M' */
+#endif
+
+/* Alternativ core deduction for older ICCARM's */
+#if !defined(__ARM_ARCH_6M__) && !defined(__ARM_ARCH_7M__) && !defined(__ARM_ARCH_7EM__) && \
+    !defined(__ARM_ARCH_8M_BASE__) && !defined(__ARM_ARCH_8M_MAIN__)
+  #if defined(__ARM6M__) && (__CORE__ == __ARM6M__)
+    #define __ARM_ARCH_6M__ 1
+  #elif defined(__ARM7M__) && (__CORE__ == __ARM7M__)
+    #define __ARM_ARCH_7M__ 1
+  #elif defined(__ARM7EM__) && (__CORE__ == __ARM7EM__)
+    #define __ARM_ARCH_7EM__  1
+  #elif defined(__ARM8M_BASELINE__) && (__CORE == __ARM8M_BASELINE__)
+    #define __ARM_ARCH_8M_BASE__ 1
+  #elif defined(__ARM8M_MAINLINE__) && (__CORE == __ARM8M_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #elif defined(__ARM8EM_MAINLINE__) && (__CORE == __ARM8EM_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #else
+    #error "Unknown target."
+  #endif
+#endif
+
+
+
+#if defined(__ARM_ARCH_6M__) && __ARM_ARCH_6M__==1
+  #define __IAR_M0_FAMILY  1
+#elif defined(__ARM_ARCH_8M_BASE__) && __ARM_ARCH_8M_BASE__==1
+  #define __IAR_M0_FAMILY  1
+#else
+  #define __IAR_M0_FAMILY  0
+#endif
+
+
+#ifndef __ASM
+  #define __ASM __asm
+#endif
+
+#ifndef __INLINE
+  #define __INLINE inline
+#endif
+
+#ifndef   __NO_RETURN
+  #if __ICCARM_V8
+    #define __NO_RETURN __attribute__((__noreturn__))
+  #else
+    #define __NO_RETURN _Pragma("object_attribute=__noreturn")
+  #endif
+#endif
+
+#ifndef   __PACKED
+  #if __ICCARM_V8
+    #define __PACKED __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED __packed
+  #endif
+#endif
+
+#ifndef   __PACKED_STRUCT
+  #if __ICCARM_V8
+    #define __PACKED_STRUCT struct __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED_STRUCT __packed struct
+  #endif
+#endif
+
+#ifndef   __PACKED_UNION
+  #if __ICCARM_V8
+    #define __PACKED_UNION union __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED_UNION __packed union
+  #endif
+#endif
+
+#ifndef   __RESTRICT
+  #define __RESTRICT            __restrict
+#endif
+
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE       static inline
+#endif
+
+#ifndef   __FORCEINLINE
+  #define __FORCEINLINE         _Pragma("inline=forced")
+#endif
+
+#ifndef   __STATIC_FORCEINLINE
+  #define __STATIC_FORCEINLINE  __FORCEINLINE __STATIC_INLINE
+#endif
+
+#ifndef __UNALIGNED_UINT16_READ
+#pragma language=save
+#pragma language=extended
+__IAR_FT uint16_t __iar_uint16_read(void const *ptr)
+{
+  return *(__packed uint16_t*)(ptr);
+}
+#pragma language=restore
+#define __UNALIGNED_UINT16_READ(PTR) __iar_uint16_read(PTR)
+#endif
+
+
+#ifndef __UNALIGNED_UINT16_WRITE
+#pragma language=save
+#pragma language=extended
+__IAR_FT void __iar_uint16_write(void const *ptr, uint16_t val)
+{
+  *(__packed uint16_t*)(ptr) = val;;
+}
+#pragma language=restore
+#define __UNALIGNED_UINT16_WRITE(PTR,VAL) __iar_uint16_write(PTR,VAL)
+#endif
+
+#ifndef __UNALIGNED_UINT32_READ
+#pragma language=save
+#pragma language=extended
+__IAR_FT uint32_t __iar_uint32_read(void const *ptr)
+{
+  return *(__packed uint32_t*)(ptr);
+}
+#pragma language=restore
+#define __UNALIGNED_UINT32_READ(PTR) __iar_uint32_read(PTR)
+#endif
+
+#ifndef __UNALIGNED_UINT32_WRITE
+#pragma language=save
+#pragma language=extended
+__IAR_FT void __iar_uint32_write(void const *ptr, uint32_t val)
+{
+  *(__packed uint32_t*)(ptr) = val;;
+}
+#pragma language=restore
+#define __UNALIGNED_UINT32_WRITE(PTR,VAL) __iar_uint32_write(PTR,VAL)
+#endif
+
+#ifndef __UNALIGNED_UINT32   /* deprecated */
+#pragma language=save
+#pragma language=extended
+__packed struct  __iar_u32 { uint32_t v; };
+#pragma language=restore
+#define __UNALIGNED_UINT32(PTR) (((struct __iar_u32 *)(PTR))->v)
+#endif
+
+#ifndef   __USED
+  #if __ICCARM_V8
+    #define __USED __attribute__((used))
+  #else
+    #define __USED _Pragma("__root")
+  #endif
+#endif
+
+#ifndef   __WEAK
+  #if __ICCARM_V8
+    #define __WEAK __attribute__((weak))
+  #else
+    #define __WEAK _Pragma("__weak")
+  #endif
+#endif
+
+
+#ifndef __ICCARM_INTRINSICS_VERSION__
+  #define __ICCARM_INTRINSICS_VERSION__  0
+#endif
+
+#if __ICCARM_INTRINSICS_VERSION__ == 2
+
+  #if defined(__CLZ)
+    #undef __CLZ
+  #endif
+  #if defined(__REVSH)
+    #undef __REVSH
+  #endif
+  #if defined(__RBIT)
+    #undef __RBIT
+  #endif
+  #if defined(__SSAT)
+    #undef __SSAT
+  #endif
+  #if defined(__USAT)
+    #undef __USAT
+  #endif
+
+  #include "iccarm_builtin.h"
+
+  #define __disable_fault_irq __iar_builtin_disable_fiq
+  #define __disable_irq       __iar_builtin_disable_interrupt
+  #define __enable_fault_irq  __iar_builtin_enable_fiq
+  #define __enable_irq        __iar_builtin_enable_interrupt
+  #define __arm_rsr           __iar_builtin_rsr
+  #define __arm_wsr           __iar_builtin_wsr
+
+
+  #define __get_APSR()                (__arm_rsr("APSR"))
+  #define __get_BASEPRI()             (__arm_rsr("BASEPRI"))
+  #define __get_CONTROL()             (__arm_rsr("CONTROL"))
+  #define __get_FAULTMASK()           (__arm_rsr("FAULTMASK"))
+
+  #if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+       (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+    #define __get_FPSCR()             (__arm_rsr("FPSCR"))
+    #define __set_FPSCR(VALUE)        (__arm_wsr("FPSCR", (VALUE)))
+  #else
+    #define __get_FPSCR()             ( 0 )
+    #define __set_FPSCR(VALUE)        ((void)VALUE)
+  #endif
+
+  #define __get_IPSR()                (__arm_rsr("IPSR"))
+  #define __get_MSP()                 (__arm_rsr("MSP"))
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure MSPLIM is RAZ/WI
+    #define __get_MSPLIM()            (0U)
+  #else
+    #define __get_MSPLIM()            (__arm_rsr("MSPLIM"))
+  #endif
+  #define __get_PRIMASK()             (__arm_rsr("PRIMASK"))
+  #define __get_PSP()                 (__arm_rsr("PSP"))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __get_PSPLIM()            (0U)
+  #else
+    #define __get_PSPLIM()            (__arm_rsr("PSPLIM"))
+  #endif
+
+  #define __get_xPSR()                (__arm_rsr("xPSR"))
+
+  #define __set_BASEPRI(VALUE)        (__arm_wsr("BASEPRI", (VALUE)))
+  #define __set_BASEPRI_MAX(VALUE)    (__arm_wsr("BASEPRI_MAX", (VALUE)))
+  #define __set_CONTROL(VALUE)        (__arm_wsr("CONTROL", (VALUE)))
+  #define __set_FAULTMASK(VALUE)      (__arm_wsr("FAULTMASK", (VALUE)))
+  #define __set_MSP(VALUE)            (__arm_wsr("MSP", (VALUE)))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure MSPLIM is RAZ/WI
+    #define __set_MSPLIM(VALUE)       ((void)(VALUE))
+  #else
+    #define __set_MSPLIM(VALUE)       (__arm_wsr("MSPLIM", (VALUE)))
+  #endif
+  #define __set_PRIMASK(VALUE)        (__arm_wsr("PRIMASK", (VALUE)))
+  #define __set_PSP(VALUE)            (__arm_wsr("PSP", (VALUE)))
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __set_PSPLIM(VALUE)       ((void)(VALUE))
+  #else
+    #define __set_PSPLIM(VALUE)       (__arm_wsr("PSPLIM", (VALUE)))
+  #endif
+
+  #define __TZ_get_CONTROL_NS()       (__arm_rsr("CONTROL_NS"))
+  #define __TZ_set_CONTROL_NS(VALUE)  (__arm_wsr("CONTROL_NS", (VALUE)))
+  #define __TZ_get_PSP_NS()           (__arm_rsr("PSP_NS"))
+  #define __TZ_set_PSP_NS(VALUE)      (__arm_wsr("PSP_NS", (VALUE)))
+  #define __TZ_get_MSP_NS()           (__arm_rsr("MSP_NS"))
+  #define __TZ_set_MSP_NS(VALUE)      (__arm_wsr("MSP_NS", (VALUE)))
+  #define __TZ_get_SP_NS()            (__arm_rsr("SP_NS"))
+  #define __TZ_set_SP_NS(VALUE)       (__arm_wsr("SP_NS", (VALUE)))
+  #define __TZ_get_PRIMASK_NS()       (__arm_rsr("PRIMASK_NS"))
+  #define __TZ_set_PRIMASK_NS(VALUE)  (__arm_wsr("PRIMASK_NS", (VALUE)))
+  #define __TZ_get_BASEPRI_NS()       (__arm_rsr("BASEPRI_NS"))
+  #define __TZ_set_BASEPRI_NS(VALUE)  (__arm_wsr("BASEPRI_NS", (VALUE)))
+  #define __TZ_get_FAULTMASK_NS()     (__arm_rsr("FAULTMASK_NS"))
+  #define __TZ_set_FAULTMASK_NS(VALUE)(__arm_wsr("FAULTMASK_NS", (VALUE)))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __TZ_get_PSPLIM_NS()      (0U)
+    #define __TZ_set_PSPLIM_NS(VALUE) ((void)(VALUE))
+  #else
+    #define __TZ_get_PSPLIM_NS()      (__arm_rsr("PSPLIM_NS"))
+    #define __TZ_set_PSPLIM_NS(VALUE) (__arm_wsr("PSPLIM_NS", (VALUE)))
+  #endif
+
+  #define __TZ_get_MSPLIM_NS()        (__arm_rsr("MSPLIM_NS"))
+  #define __TZ_set_MSPLIM_NS(VALUE)   (__arm_wsr("MSPLIM_NS", (VALUE)))
+
+  #define __NOP     __iar_builtin_no_operation
+
+  #define __CLZ     __iar_builtin_CLZ
+  #define __CLREX   __iar_builtin_CLREX
+
+  #define __DMB     __iar_builtin_DMB
+  #define __DSB     __iar_builtin_DSB
+  #define __ISB     __iar_builtin_ISB
+
+  #define __LDREXB  __iar_builtin_LDREXB
+  #define __LDREXH  __iar_builtin_LDREXH
+  #define __LDREXW  __iar_builtin_LDREX
+
+  #define __RBIT    __iar_builtin_RBIT
+  #define __REV     __iar_builtin_REV
+  #define __REV16   __iar_builtin_REV16
+
+  __IAR_FT int16_t __REVSH(int16_t val)
+  {
+    return (int16_t) __iar_builtin_REVSH(val);
+  }
+
+  #define __ROR     __iar_builtin_ROR
+  #define __RRX     __iar_builtin_RRX
+
+  #define __SEV     __iar_builtin_SEV
+
+  #if !__IAR_M0_FAMILY
+    #define __SSAT    __iar_builtin_SSAT
+  #endif
+
+  #define __STREXB  __iar_builtin_STREXB
+  #define __STREXH  __iar_builtin_STREXH
+  #define __STREXW  __iar_builtin_STREX
+
+  #if !__IAR_M0_FAMILY
+    #define __USAT    __iar_builtin_USAT
+  #endif
+
+  #define __WFE     __iar_builtin_WFE
+  #define __WFI     __iar_builtin_WFI
+
+  #if __ARM_MEDIA__
+    #define __SADD8   __iar_builtin_SADD8
+    #define __QADD8   __iar_builtin_QADD8
+    #define __SHADD8  __iar_builtin_SHADD8
+    #define __UADD8   __iar_builtin_UADD8
+    #define __UQADD8  __iar_builtin_UQADD8
+    #define __UHADD8  __iar_builtin_UHADD8
+    #define __SSUB8   __iar_builtin_SSUB8
+    #define __QSUB8   __iar_builtin_QSUB8
+    #define __SHSUB8  __iar_builtin_SHSUB8
+    #define __USUB8   __iar_builtin_USUB8
+    #define __UQSUB8  __iar_builtin_UQSUB8
+    #define __UHSUB8  __iar_builtin_UHSUB8
+    #define __SADD16  __iar_builtin_SADD16
+    #define __QADD16  __iar_builtin_QADD16
+    #define __SHADD16 __iar_builtin_SHADD16
+    #define __UADD16  __iar_builtin_UADD16
+    #define __UQADD16 __iar_builtin_UQADD16
+    #define __UHADD16 __iar_builtin_UHADD16
+    #define __SSUB16  __iar_builtin_SSUB16
+    #define __QSUB16  __iar_builtin_QSUB16
+    #define __SHSUB16 __iar_builtin_SHSUB16
+    #define __USUB16  __iar_builtin_USUB16
+    #define __UQSUB16 __iar_builtin_UQSUB16
+    #define __UHSUB16 __iar_builtin_UHSUB16
+    #define __SASX    __iar_builtin_SASX
+    #define __QASX    __iar_builtin_QASX
+    #define __SHASX   __iar_builtin_SHASX
+    #define __UASX    __iar_builtin_UASX
+    #define __UQASX   __iar_builtin_UQASX
+    #define __UHASX   __iar_builtin_UHASX
+    #define __SSAX    __iar_builtin_SSAX
+    #define __QSAX    __iar_builtin_QSAX
+    #define __SHSAX   __iar_builtin_SHSAX
+    #define __USAX    __iar_builtin_USAX
+    #define __UQSAX   __iar_builtin_UQSAX
+    #define __UHSAX   __iar_builtin_UHSAX
+    #define __USAD8   __iar_builtin_USAD8
+    #define __USADA8  __iar_builtin_USADA8
+    #define __SSAT16  __iar_builtin_SSAT16
+    #define __USAT16  __iar_builtin_USAT16
+    #define __UXTB16  __iar_builtin_UXTB16
+    #define __UXTAB16 __iar_builtin_UXTAB16
+    #define __SXTB16  __iar_builtin_SXTB16
+    #define __SXTAB16 __iar_builtin_SXTAB16
+    #define __SMUAD   __iar_builtin_SMUAD
+    #define __SMUADX  __iar_builtin_SMUADX
+    #define __SMMLA   __iar_builtin_SMMLA
+    #define __SMLAD   __iar_builtin_SMLAD
+    #define __SMLADX  __iar_builtin_SMLADX
+    #define __SMLALD  __iar_builtin_SMLALD
+    #define __SMLALDX __iar_builtin_SMLALDX
+    #define __SMUSD   __iar_builtin_SMUSD
+    #define __SMUSDX  __iar_builtin_SMUSDX
+    #define __SMLSD   __iar_builtin_SMLSD
+    #define __SMLSDX  __iar_builtin_SMLSDX
+    #define __SMLSLD  __iar_builtin_SMLSLD
+    #define __SMLSLDX __iar_builtin_SMLSLDX
+    #define __SEL     __iar_builtin_SEL
+    #define __QADD    __iar_builtin_QADD
+    #define __QSUB    __iar_builtin_QSUB
+    #define __PKHBT   __iar_builtin_PKHBT
+    #define __PKHTB   __iar_builtin_PKHTB
+  #endif
+
+#else /* __ICCARM_INTRINSICS_VERSION__ == 2 */
+
+  #if __IAR_M0_FAMILY
+   /* Avoid clash between intrinsics.h and arm_math.h when compiling for Cortex-M0. */
+    #define __CLZ  __cmsis_iar_clz_not_active
+    #define __SSAT __cmsis_iar_ssat_not_active
+    #define __USAT __cmsis_iar_usat_not_active
+    #define __RBIT __cmsis_iar_rbit_not_active
+    #define __get_APSR  __cmsis_iar_get_APSR_not_active
+  #endif
+
+
+  #if (!((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+         (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     ))
+    #define __get_FPSCR __cmsis_iar_get_FPSR_not_active
+    #define __set_FPSCR __cmsis_iar_set_FPSR_not_active
+  #endif
+
+  #ifdef __INTRINSICS_INCLUDED
+  #error intrinsics.h is already included previously!
+  #endif
+
+  #include <intrinsics.h>
+
+  #if __IAR_M0_FAMILY
+   /* Avoid clash between intrinsics.h and arm_math.h when compiling for Cortex-M0. */
+    #undef __CLZ
+    #undef __SSAT
+    #undef __USAT
+    #undef __RBIT
+    #undef __get_APSR
+
+    __STATIC_INLINE uint8_t __CLZ(uint32_t data)
+    {
+      if (data == 0U) { return 32U; }
+
+      uint32_t count = 0U;
+      uint32_t mask = 0x80000000U;
+
+      while ((data & mask) == 0U)
+      {
+        count += 1U;
+        mask = mask >> 1U;
+      }
+      return count;
+    }
+
+    __STATIC_INLINE uint32_t __RBIT(uint32_t v)
+    {
+      uint8_t sc = 31U;
+      uint32_t r = v;
+      for (v >>= 1U; v; v >>= 1U)
+      {
+        r <<= 1U;
+        r |= v & 1U;
+        sc--;
+      }
+      return (r << sc);
+    }
+
+    __STATIC_INLINE  uint32_t __get_APSR(void)
+    {
+      uint32_t res;
+      __asm("MRS      %0,APSR" : "=r" (res));
+      return res;
+    }
+
+  #endif
+
+  #if (!((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+         (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     ))
+    #undef __get_FPSCR
+    #undef __set_FPSCR
+    #define __get_FPSCR()       (0)
+    #define __set_FPSCR(VALUE)  ((void)VALUE)
+  #endif
+
+  #pragma diag_suppress=Pe940
+  #pragma diag_suppress=Pe177
+
+  #define __enable_irq    __enable_interrupt
+  #define __disable_irq   __disable_interrupt
+  #define __NOP           __no_operation
+
+  #define __get_xPSR      __get_PSR
+
+  #if (!defined(__ARM_ARCH_6M__) || __ARM_ARCH_6M__==0)
+
+    __IAR_FT uint32_t __LDREXW(uint32_t volatile *ptr)
+    {
+      return __LDREX((unsigned long *)ptr);
+    }
+
+    __IAR_FT uint32_t __STREXW(uint32_t value, uint32_t volatile *ptr)
+    {
+      return __STREX(value, (unsigned long *)ptr);
+    }
+  #endif
+
+
+  /* __CORTEX_M is defined in core_cm0.h, core_cm3.h and core_cm4.h. */
+  #if (__CORTEX_M >= 0x03)
+
+    __IAR_FT uint32_t __RRX(uint32_t value)
+    {
+      uint32_t result;
+      __ASM("RRX      %0, %1" : "=r"(result) : "r" (value) : "cc");
+      return(result);
+    }
+
+    __IAR_FT void __set_BASEPRI_MAX(uint32_t value)
+    {
+      __asm volatile("MSR      BASEPRI_MAX,%0"::"r" (value));
+    }
+
+
+    #define __enable_fault_irq  __enable_fiq
+    #define __disable_fault_irq __disable_fiq
+
+
+  #endif /* (__CORTEX_M >= 0x03) */
+
+  __IAR_FT uint32_t __ROR(uint32_t op1, uint32_t op2)
+  {
+    return (op1 >> op2) | (op1 << ((sizeof(op1)*8)-op2));
+  }
+
+  #if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \
+       (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1))    )
+
+   __IAR_FT uint32_t __get_MSPLIM(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure MSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,MSPLIM" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __set_MSPLIM(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure MSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      MSPLIM,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t __get_PSPLIM(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,PSPLIM" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __set_PSPLIM(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      PSPLIM,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t __TZ_get_CONTROL_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,CONTROL_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_CONTROL_NS(uint32_t value)
+    {
+      __asm volatile("MSR      CONTROL_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PSP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,PSP_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PSP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      PSP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_MSP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,MSP_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_MSP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      MSP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_SP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,SP_NS" : "=r" (res));
+      return res;
+    }
+    __IAR_FT void   __TZ_set_SP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      SP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PRIMASK_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,PRIMASK_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PRIMASK_NS(uint32_t value)
+    {
+      __asm volatile("MSR      PRIMASK_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_BASEPRI_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,BASEPRI_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_BASEPRI_NS(uint32_t value)
+    {
+      __asm volatile("MSR      BASEPRI_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_FAULTMASK_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,FAULTMASK_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_FAULTMASK_NS(uint32_t value)
+    {
+      __asm volatile("MSR      FAULTMASK_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PSPLIM_NS(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,PSPLIM_NS" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PSPLIM_NS(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      PSPLIM_NS,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t   __TZ_get_MSPLIM_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,MSPLIM_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_MSPLIM_NS(uint32_t value)
+    {
+      __asm volatile("MSR      MSPLIM_NS,%0" :: "r" (value));
+    }
+
+  #endif /* __ARM_ARCH_8M_MAIN__ or __ARM_ARCH_8M_BASE__ */
+
+#endif   /* __ICCARM_INTRINSICS_VERSION__ == 2 */
+
+#define __BKPT(value)    __asm volatile ("BKPT     %0" : : "i"(value))
+
+#if __IAR_M0_FAMILY
+  __STATIC_INLINE int32_t __SSAT(int32_t val, uint32_t sat)
+  {
+    if ((sat >= 1U) && (sat <= 32U))
+    {
+      const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U);
+      const int32_t min = -1 - max ;
+      if (val > max)
+      {
+        return max;
+      }
+      else if (val < min)
+      {
+        return min;
+      }
+    }
+    return val;
+  }
+
+  __STATIC_INLINE uint32_t __USAT(int32_t val, uint32_t sat)
+  {
+    if (sat <= 31U)
+    {
+      const uint32_t max = ((1U << sat) - 1U);
+      if (val > (int32_t)max)
+      {
+        return max;
+      }
+      else if (val < 0)
+      {
+        return 0U;
+      }
+    }
+    return (uint32_t)val;
+  }
+#endif
+
+#if (__CORTEX_M >= 0x03)   /* __CORTEX_M is defined in core_cm0.h, core_cm3.h and core_cm4.h. */
+
+  __IAR_FT uint8_t __LDRBT(volatile uint8_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRBT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDRHT(volatile uint16_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRHT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDRT(volatile uint32_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return res;
+  }
+
+  __IAR_FT void __STRBT(uint8_t value, volatile uint8_t *addr)
+  {
+    __ASM("STRBT %1, [%0]" : : "r" (addr), "r" ((uint32_t)value) : "memory");
+  }
+
+  __IAR_FT void __STRHT(uint16_t value, volatile uint16_t *addr)
+  {
+    __ASM("STRHT %1, [%0]" : : "r" (addr), "r" ((uint32_t)value) : "memory");
+  }
+
+  __IAR_FT void __STRT(uint32_t value, volatile uint32_t *addr)
+  {
+    __ASM("STRT %1, [%0]" : : "r" (addr), "r" (value) : "memory");
+  }
+
+#endif /* (__CORTEX_M >= 0x03) */
+
+#if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \
+     (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1))    )
+
+
+  __IAR_FT uint8_t __LDAB(volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAB %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDAH(volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAH %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDA(volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDA %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return res;
+  }
+
+  __IAR_FT void __STLB(uint8_t value, volatile uint8_t *ptr)
+  {
+    __ASM volatile ("STLB %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT void __STLH(uint16_t value, volatile uint16_t *ptr)
+  {
+    __ASM volatile ("STLH %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT void __STL(uint32_t value, volatile uint32_t *ptr)
+  {
+    __ASM volatile ("STL %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT uint8_t __LDAEXB(volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEXB %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDAEXH(volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEXH %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDAEX(volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEX %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEXB(uint8_t value, volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEXB %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEXH(uint16_t value, volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEXH %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEX(uint32_t value, volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEX %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+#endif /* __ARM_ARCH_8M_MAIN__ or __ARM_ARCH_8M_BASE__ */
+
+#undef __IAR_FT
+#undef __IAR_M0_FAMILY
+#undef __ICCARM_V8
+
+#pragma diag_default=Pe940
+#pragma diag_default=Pe177
+
+#endif /* __CMSIS_ICCARM_H__ */

fw_hal/Drivers/CMSIS/Include/cmsis_version.h

@@ -0,0 +1,39 @@
+/**************************************************************************//**
+ * @file     cmsis_version.h
+ * @brief    CMSIS Core(M) Version definitions
+ * @version  V5.0.2
+ * @date     19. April 2017
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2017 ARM Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CMSIS_VERSION_H
+#define __CMSIS_VERSION_H
+
+/*  CMSIS Version definitions */
+#define __CM_CMSIS_VERSION_MAIN  ( 5U)                                      /*!< [31:16] CMSIS Core(M) main version */
+#define __CM_CMSIS_VERSION_SUB   ( 1U)                                      /*!< [15:0]  CMSIS Core(M) sub version */
+#define __CM_CMSIS_VERSION       ((__CM_CMSIS_VERSION_MAIN << 16U) | \
+                                   __CM_CMSIS_VERSION_SUB           )       /*!< CMSIS Core(M) version number */
+#endif

fw_hal/Drivers/CMSIS/Include/core_cm0.h

@@ -0,0 +1,949 @@
+/**************************************************************************//**
+ * @file     core_cm0.h
+ * @brief    CMSIS Cortex-M0 Core Peripheral Access Layer Header File
+ * @version  V5.0.5
+ * @date     28. May 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CORE_CM0_H_GENERIC
+#define __CORE_CM0_H_GENERIC
+
+#include <stdint.h>
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/**
+  \page CMSIS_MISRA_Exceptions  MISRA-C:2004 Compliance Exceptions
+  CMSIS violates the following MISRA-C:2004 rules:
+
+   \li Required Rule 8.5, object/function definition in header file.<br>
+     Function definitions in header files are used to allow 'inlining'.
+
+   \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.<br>
+     Unions are used for effective representation of core registers.
+
+   \li Advisory Rule 19.7, Function-like macro defined.<br>
+     Function-like macros are used to allow more efficient code.
+ */
+
+
+/*******************************************************************************
+ *                 CMSIS definitions
+ ******************************************************************************/
+/**
+  \ingroup Cortex_M0
+  @{
+ */
+
+#include "cmsis_version.h"
+ 
+/*  CMSIS CM0 definitions */
+#define __CM0_CMSIS_VERSION_MAIN  (__CM_CMSIS_VERSION_MAIN)              /*!< \deprecated [31:16] CMSIS HAL main version */
+#define __CM0_CMSIS_VERSION_SUB   (__CM_CMSIS_VERSION_SUB)               /*!< \deprecated [15:0]  CMSIS HAL sub version */
+#define __CM0_CMSIS_VERSION       ((__CM0_CMSIS_VERSION_MAIN << 16U) | \
+                                    __CM0_CMSIS_VERSION_SUB           )  /*!< \deprecated CMSIS HAL version number */
+
+#define __CORTEX_M                (0U)                                   /*!< Cortex-M Core */
+
+/** __FPU_USED indicates whether an FPU is used or not.
+    This core does not support an FPU at all
+*/
+#define __FPU_USED       0U
+
+#if defined ( __CC_ARM )
+  #if defined __TARGET_FPU_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #if defined __ARM_PCS_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __GNUC__ )
+  #if defined (__VFP_FP__) && !defined(__SOFTFP__)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __ICCARM__ )
+  #if defined __ARMVFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TI_ARM__ )
+  #if defined __TI_VFP_SUPPORT__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TASKING__ )
+  #if defined __FPU_VFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __CSMC__ )
+  #if ( __CSMC__ & 0x400U)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#endif
+
+#include "cmsis_compiler.h"               /* CMSIS compiler specific defines */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM0_H_GENERIC */
+
+#ifndef __CMSIS_GENERIC
+
+#ifndef __CORE_CM0_H_DEPENDANT
+#define __CORE_CM0_H_DEPENDANT
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* check device defines and use defaults */
+#if defined __CHECK_DEVICE_DEFINES
+  #ifndef __CM0_REV
+    #define __CM0_REV               0x0000U
+    #warning "__CM0_REV not defined in device header file; using default!"
+  #endif
+
+  #ifndef __NVIC_PRIO_BITS
+    #define __NVIC_PRIO_BITS          2U
+    #warning "__NVIC_PRIO_BITS not defined in device header file; using default!"
+  #endif
+
+  #ifndef __Vendor_SysTickConfig
+    #define __Vendor_SysTickConfig    0U
+    #warning "__Vendor_SysTickConfig not defined in device header file; using default!"
+  #endif
+#endif
+
+/* IO definitions (access restrictions to peripheral registers) */
+/**
+    \defgroup CMSIS_glob_defs CMSIS Global Defines
+
+    <strong>IO Type Qualifiers</strong> are used
+    \li to specify the access to peripheral variables.
+    \li for automatic generation of peripheral register debug information.
+*/
+#ifdef __cplusplus
+  #define   __I     volatile             /*!< Defines 'read only' permissions */
+#else
+  #define   __I     volatile const       /*!< Defines 'read only' permissions */
+#endif
+#define     __O     volatile             /*!< Defines 'write only' permissions */
+#define     __IO    volatile             /*!< Defines 'read / write' permissions */
+
+/* following defines should be used for structure members */
+#define     __IM     volatile const      /*! Defines 'read only' structure member permissions */
+#define     __OM     volatile            /*! Defines 'write only' structure member permissions */
+#define     __IOM    volatile            /*! Defines 'read / write' structure member permissions */
+
+/*@} end of group Cortex_M0 */
+
+
+
+/*******************************************************************************
+ *                 Register Abstraction
+  Core Register contain:
+  - Core Register
+  - Core NVIC Register
+  - Core SCB Register
+  - Core SysTick Register
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_core_register Defines and Type Definitions
+  \brief Type definitions and defines for Cortex-M processor based devices.
+*/
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_CORE  Status and Control Registers
+  \brief      Core Register type definitions.
+  @{
+ */
+
+/**
+  \brief  Union type to access the Application Program Status Register (APSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:28;              /*!< bit:  0..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} APSR_Type;
+
+/* APSR Register Definitions */
+#define APSR_N_Pos                         31U                                            /*!< APSR: N Position */
+#define APSR_N_Msk                         (1UL << APSR_N_Pos)                            /*!< APSR: N Mask */
+
+#define APSR_Z_Pos                         30U                                            /*!< APSR: Z Position */
+#define APSR_Z_Msk                         (1UL << APSR_Z_Pos)                            /*!< APSR: Z Mask */
+
+#define APSR_C_Pos                         29U                                            /*!< APSR: C Position */
+#define APSR_C_Msk                         (1UL << APSR_C_Pos)                            /*!< APSR: C Mask */
+
+#define APSR_V_Pos                         28U                                            /*!< APSR: V Position */
+#define APSR_V_Msk                         (1UL << APSR_V_Pos)                            /*!< APSR: V Mask */
+
+
+/**
+  \brief  Union type to access the Interrupt Program Status Register (IPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:23;              /*!< bit:  9..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} IPSR_Type;
+
+/* IPSR Register Definitions */
+#define IPSR_ISR_Pos                        0U                                            /*!< IPSR: ISR Position */
+#define IPSR_ISR_Msk                       (0x1FFUL /*<< IPSR_ISR_Pos*/)                  /*!< IPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Special-Purpose Program Status Registers (xPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:15;              /*!< bit:  9..23  Reserved */
+    uint32_t T:1;                        /*!< bit:     24  Thumb bit        (read 0) */
+    uint32_t _reserved1:3;               /*!< bit: 25..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} xPSR_Type;
+
+/* xPSR Register Definitions */
+#define xPSR_N_Pos                         31U                                            /*!< xPSR: N Position */
+#define xPSR_N_Msk                         (1UL << xPSR_N_Pos)                            /*!< xPSR: N Mask */
+
+#define xPSR_Z_Pos                         30U                                            /*!< xPSR: Z Position */
+#define xPSR_Z_Msk                         (1UL << xPSR_Z_Pos)                            /*!< xPSR: Z Mask */
+
+#define xPSR_C_Pos                         29U                                            /*!< xPSR: C Position */
+#define xPSR_C_Msk                         (1UL << xPSR_C_Pos)                            /*!< xPSR: C Mask */
+
+#define xPSR_V_Pos                         28U                                            /*!< xPSR: V Position */
+#define xPSR_V_Msk                         (1UL << xPSR_V_Pos)                            /*!< xPSR: V Mask */
+
+#define xPSR_T_Pos                         24U                                            /*!< xPSR: T Position */
+#define xPSR_T_Msk                         (1UL << xPSR_T_Pos)                            /*!< xPSR: T Mask */
+
+#define xPSR_ISR_Pos                        0U                                            /*!< xPSR: ISR Position */
+#define xPSR_ISR_Msk                       (0x1FFUL /*<< xPSR_ISR_Pos*/)                  /*!< xPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Control Registers (CONTROL).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:1;               /*!< bit:      0  Reserved */
+    uint32_t SPSEL:1;                    /*!< bit:      1  Stack to be used */
+    uint32_t _reserved1:30;              /*!< bit:  2..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} CONTROL_Type;
+
+/* CONTROL Register Definitions */
+#define CONTROL_SPSEL_Pos                   1U                                            /*!< CONTROL: SPSEL Position */
+#define CONTROL_SPSEL_Msk                  (1UL << CONTROL_SPSEL_Pos)                     /*!< CONTROL: SPSEL Mask */
+
+/*@} end of group CMSIS_CORE */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_NVIC  Nested Vectored Interrupt Controller (NVIC)
+  \brief      Type definitions for the NVIC Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the Nested Vectored Interrupt Controller (NVIC).
+ */
+typedef struct
+{
+  __IOM uint32_t ISER[1U];               /*!< Offset: 0x000 (R/W)  Interrupt Set Enable Register */
+        uint32_t RESERVED0[31U];
+  __IOM uint32_t ICER[1U];               /*!< Offset: 0x080 (R/W)  Interrupt Clear Enable Register */
+        uint32_t RSERVED1[31U];
+  __IOM uint32_t ISPR[1U];               /*!< Offset: 0x100 (R/W)  Interrupt Set Pending Register */
+        uint32_t RESERVED2[31U];
+  __IOM uint32_t ICPR[1U];               /*!< Offset: 0x180 (R/W)  Interrupt Clear Pending Register */
+        uint32_t RESERVED3[31U];
+        uint32_t RESERVED4[64U];
+  __IOM uint32_t IP[8U];                 /*!< Offset: 0x300 (R/W)  Interrupt Priority Register */
+}  NVIC_Type;
+
+/*@} end of group CMSIS_NVIC */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCB     System Control Block (SCB)
+  \brief    Type definitions for the System Control Block Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control Block (SCB).
+ */
+typedef struct
+{
+  __IM  uint32_t CPUID;                  /*!< Offset: 0x000 (R/ )  CPUID Base Register */
+  __IOM uint32_t ICSR;                   /*!< Offset: 0x004 (R/W)  Interrupt Control and State Register */
+        uint32_t RESERVED0;
+  __IOM uint32_t AIRCR;                  /*!< Offset: 0x00C (R/W)  Application Interrupt and Reset Control Register */
+  __IOM uint32_t SCR;                    /*!< Offset: 0x010 (R/W)  System Control Register */
+  __IOM uint32_t CCR;                    /*!< Offset: 0x014 (R/W)  Configuration Control Register */
+        uint32_t RESERVED1;
+  __IOM uint32_t SHP[2U];                /*!< Offset: 0x01C (R/W)  System Handlers Priority Registers. [0] is RESERVED */
+  __IOM uint32_t SHCSR;                  /*!< Offset: 0x024 (R/W)  System Handler Control and State Register */
+} SCB_Type;
+
+/* SCB CPUID Register Definitions */
+#define SCB_CPUID_IMPLEMENTER_Pos          24U                                            /*!< SCB CPUID: IMPLEMENTER Position */
+#define SCB_CPUID_IMPLEMENTER_Msk          (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos)          /*!< SCB CPUID: IMPLEMENTER Mask */
+
+#define SCB_CPUID_VARIANT_Pos              20U                                            /*!< SCB CPUID: VARIANT Position */
+#define SCB_CPUID_VARIANT_Msk              (0xFUL << SCB_CPUID_VARIANT_Pos)               /*!< SCB CPUID: VARIANT Mask */
+
+#define SCB_CPUID_ARCHITECTURE_Pos         16U                                            /*!< SCB CPUID: ARCHITECTURE Position */
+#define SCB_CPUID_ARCHITECTURE_Msk         (0xFUL << SCB_CPUID_ARCHITECTURE_Pos)          /*!< SCB CPUID: ARCHITECTURE Mask */
+
+#define SCB_CPUID_PARTNO_Pos                4U                                            /*!< SCB CPUID: PARTNO Position */
+#define SCB_CPUID_PARTNO_Msk               (0xFFFUL << SCB_CPUID_PARTNO_Pos)              /*!< SCB CPUID: PARTNO Mask */
+
+#define SCB_CPUID_REVISION_Pos              0U                                            /*!< SCB CPUID: REVISION Position */
+#define SCB_CPUID_REVISION_Msk             (0xFUL /*<< SCB_CPUID_REVISION_Pos*/)          /*!< SCB CPUID: REVISION Mask */
+
+/* SCB Interrupt Control State Register Definitions */
+#define SCB_ICSR_NMIPENDSET_Pos            31U                                            /*!< SCB ICSR: NMIPENDSET Position */
+#define SCB_ICSR_NMIPENDSET_Msk            (1UL << SCB_ICSR_NMIPENDSET_Pos)               /*!< SCB ICSR: NMIPENDSET Mask */
+
+#define SCB_ICSR_PENDSVSET_Pos             28U                                            /*!< SCB ICSR: PENDSVSET Position */
+#define SCB_ICSR_PENDSVSET_Msk             (1UL << SCB_ICSR_PENDSVSET_Pos)                /*!< SCB ICSR: PENDSVSET Mask */
+
+#define SCB_ICSR_PENDSVCLR_Pos             27U                                            /*!< SCB ICSR: PENDSVCLR Position */
+#define SCB_ICSR_PENDSVCLR_Msk             (1UL << SCB_ICSR_PENDSVCLR_Pos)                /*!< SCB ICSR: PENDSVCLR Mask */
+
+#define SCB_ICSR_PENDSTSET_Pos             26U                                            /*!< SCB ICSR: PENDSTSET Position */
+#define SCB_ICSR_PENDSTSET_Msk             (1UL << SCB_ICSR_PENDSTSET_Pos)                /*!< SCB ICSR: PENDSTSET Mask */
+
+#define SCB_ICSR_PENDSTCLR_Pos             25U                                            /*!< SCB ICSR: PENDSTCLR Position */
+#define SCB_ICSR_PENDSTCLR_Msk             (1UL << SCB_ICSR_PENDSTCLR_Pos)                /*!< SCB ICSR: PENDSTCLR Mask */
+
+#define SCB_ICSR_ISRPREEMPT_Pos            23U                                            /*!< SCB ICSR: ISRPREEMPT Position */
+#define SCB_ICSR_ISRPREEMPT_Msk            (1UL << SCB_ICSR_ISRPREEMPT_Pos)               /*!< SCB ICSR: ISRPREEMPT Mask */
+
+#define SCB_ICSR_ISRPENDING_Pos            22U                                            /*!< SCB ICSR: ISRPENDING Position */
+#define SCB_ICSR_ISRPENDING_Msk            (1UL << SCB_ICSR_ISRPENDING_Pos)               /*!< SCB ICSR: ISRPENDING Mask */
+
+#define SCB_ICSR_VECTPENDING_Pos           12U                                            /*!< SCB ICSR: VECTPENDING Position */
+#define SCB_ICSR_VECTPENDING_Msk           (0x1FFUL << SCB_ICSR_VECTPENDING_Pos)          /*!< SCB ICSR: VECTPENDING Mask */
+
+#define SCB_ICSR_VECTACTIVE_Pos             0U                                            /*!< SCB ICSR: VECTACTIVE Position */
+#define SCB_ICSR_VECTACTIVE_Msk            (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/)       /*!< SCB ICSR: VECTACTIVE Mask */
+
+/* SCB Application Interrupt and Reset Control Register Definitions */
+#define SCB_AIRCR_VECTKEY_Pos              16U                                            /*!< SCB AIRCR: VECTKEY Position */
+#define SCB_AIRCR_VECTKEY_Msk              (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos)            /*!< SCB AIRCR: VECTKEY Mask */
+
+#define SCB_AIRCR_VECTKEYSTAT_Pos          16U                                            /*!< SCB AIRCR: VECTKEYSTAT Position */
+#define SCB_AIRCR_VECTKEYSTAT_Msk          (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos)        /*!< SCB AIRCR: VECTKEYSTAT Mask */
+
+#define SCB_AIRCR_ENDIANESS_Pos            15U                                            /*!< SCB AIRCR: ENDIANESS Position */
+#define SCB_AIRCR_ENDIANESS_Msk            (1UL << SCB_AIRCR_ENDIANESS_Pos)               /*!< SCB AIRCR: ENDIANESS Mask */
+
+#define SCB_AIRCR_SYSRESETREQ_Pos           2U                                            /*!< SCB AIRCR: SYSRESETREQ Position */
+#define SCB_AIRCR_SYSRESETREQ_Msk          (1UL << SCB_AIRCR_SYSRESETREQ_Pos)             /*!< SCB AIRCR: SYSRESETREQ Mask */
+
+#define SCB_AIRCR_VECTCLRACTIVE_Pos         1U                                            /*!< SCB AIRCR: VECTCLRACTIVE Position */
+#define SCB_AIRCR_VECTCLRACTIVE_Msk        (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos)           /*!< SCB AIRCR: VECTCLRACTIVE Mask */
+
+/* SCB System Control Register Definitions */
+#define SCB_SCR_SEVONPEND_Pos               4U                                            /*!< SCB SCR: SEVONPEND Position */
+#define SCB_SCR_SEVONPEND_Msk              (1UL << SCB_SCR_SEVONPEND_Pos)                 /*!< SCB SCR: SEVONPEND Mask */
+
+#define SCB_SCR_SLEEPDEEP_Pos               2U                                            /*!< SCB SCR: SLEEPDEEP Position */
+#define SCB_SCR_SLEEPDEEP_Msk              (1UL << SCB_SCR_SLEEPDEEP_Pos)                 /*!< SCB SCR: SLEEPDEEP Mask */
+
+#define SCB_SCR_SLEEPONEXIT_Pos             1U                                            /*!< SCB SCR: SLEEPONEXIT Position */
+#define SCB_SCR_SLEEPONEXIT_Msk            (1UL << SCB_SCR_SLEEPONEXIT_Pos)               /*!< SCB SCR: SLEEPONEXIT Mask */
+
+/* SCB Configuration Control Register Definitions */
+#define SCB_CCR_STKALIGN_Pos                9U                                            /*!< SCB CCR: STKALIGN Position */
+#define SCB_CCR_STKALIGN_Msk               (1UL << SCB_CCR_STKALIGN_Pos)                  /*!< SCB CCR: STKALIGN Mask */
+
+#define SCB_CCR_UNALIGN_TRP_Pos             3U                                            /*!< SCB CCR: UNALIGN_TRP Position */
+#define SCB_CCR_UNALIGN_TRP_Msk            (1UL << SCB_CCR_UNALIGN_TRP_Pos)               /*!< SCB CCR: UNALIGN_TRP Mask */
+
+/* SCB System Handler Control and State Register Definitions */
+#define SCB_SHCSR_SVCALLPENDED_Pos         15U                                            /*!< SCB SHCSR: SVCALLPENDED Position */
+#define SCB_SHCSR_SVCALLPENDED_Msk         (1UL << SCB_SHCSR_SVCALLPENDED_Pos)            /*!< SCB SHCSR: SVCALLPENDED Mask */
+
+/*@} end of group CMSIS_SCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SysTick     System Tick Timer (SysTick)
+  \brief    Type definitions for the System Timer Registers.
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Timer (SysTick).
+ */
+typedef struct
+{
+  __IOM uint32_t CTRL;                   /*!< Offset: 0x000 (R/W)  SysTick Control and Status Register */
+  __IOM uint32_t LOAD;                   /*!< Offset: 0x004 (R/W)  SysTick Reload Value Register */
+  __IOM uint32_t VAL;                    /*!< Offset: 0x008 (R/W)  SysTick Current Value Register */
+  __IM  uint32_t CALIB;                  /*!< Offset: 0x00C (R/ )  SysTick Calibration Register */
+} SysTick_Type;
+
+/* SysTick Control / Status Register Definitions */
+#define SysTick_CTRL_COUNTFLAG_Pos         16U                                            /*!< SysTick CTRL: COUNTFLAG Position */
+#define SysTick_CTRL_COUNTFLAG_Msk         (1UL << SysTick_CTRL_COUNTFLAG_Pos)            /*!< SysTick CTRL: COUNTFLAG Mask */
+
+#define SysTick_CTRL_CLKSOURCE_Pos          2U                                            /*!< SysTick CTRL: CLKSOURCE Position */
+#define SysTick_CTRL_CLKSOURCE_Msk         (1UL << SysTick_CTRL_CLKSOURCE_Pos)            /*!< SysTick CTRL: CLKSOURCE Mask */
+
+#define SysTick_CTRL_TICKINT_Pos            1U                                            /*!< SysTick CTRL: TICKINT Position */
+#define SysTick_CTRL_TICKINT_Msk           (1UL << SysTick_CTRL_TICKINT_Pos)              /*!< SysTick CTRL: TICKINT Mask */
+
+#define SysTick_CTRL_ENABLE_Pos             0U                                            /*!< SysTick CTRL: ENABLE Position */
+#define SysTick_CTRL_ENABLE_Msk            (1UL /*<< SysTick_CTRL_ENABLE_Pos*/)           /*!< SysTick CTRL: ENABLE Mask */
+
+/* SysTick Reload Register Definitions */
+#define SysTick_LOAD_RELOAD_Pos             0U                                            /*!< SysTick LOAD: RELOAD Position */
+#define SysTick_LOAD_RELOAD_Msk            (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/)    /*!< SysTick LOAD: RELOAD Mask */
+
+/* SysTick Current Register Definitions */
+#define SysTick_VAL_CURRENT_Pos             0U                                            /*!< SysTick VAL: CURRENT Position */
+#define SysTick_VAL_CURRENT_Msk            (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/)    /*!< SysTick VAL: CURRENT Mask */
+
+/* SysTick Calibration Register Definitions */
+#define SysTick_CALIB_NOREF_Pos            31U                                            /*!< SysTick CALIB: NOREF Position */
+#define SysTick_CALIB_NOREF_Msk            (1UL << SysTick_CALIB_NOREF_Pos)               /*!< SysTick CALIB: NOREF Mask */
+
+#define SysTick_CALIB_SKEW_Pos             30U                                            /*!< SysTick CALIB: SKEW Position */
+#define SysTick_CALIB_SKEW_Msk             (1UL << SysTick_CALIB_SKEW_Pos)                /*!< SysTick CALIB: SKEW Mask */
+
+#define SysTick_CALIB_TENMS_Pos             0U                                            /*!< SysTick CALIB: TENMS Position */
+#define SysTick_CALIB_TENMS_Msk            (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/)    /*!< SysTick CALIB: TENMS Mask */
+
+/*@} end of group CMSIS_SysTick */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_CoreDebug       Core Debug Registers (CoreDebug)
+  \brief    Cortex-M0 Core Debug Registers (DCB registers, SHCSR, and DFSR) are only accessible over DAP and not via processor.
+            Therefore they are not covered by the Cortex-M0 header file.
+  @{
+ */
+/*@} end of group CMSIS_CoreDebug */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_bitfield     Core register bit field macros
+  \brief      Macros for use with bit field definitions (xxx_Pos, xxx_Msk).
+  @{
+ */
+
+/**
+  \brief   Mask and shift a bit field value for use in a register bit range.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of the bit field. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted value.
+*/
+#define _VAL2FLD(field, value)    (((uint32_t)(value) << field ## _Pos) & field ## _Msk)
+
+/**
+  \brief     Mask and shift a register value to extract a bit filed value.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of register. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted bit field value.
+*/
+#define _FLD2VAL(field, value)    (((uint32_t)(value) & field ## _Msk) >> field ## _Pos)
+
+/*@} end of group CMSIS_core_bitfield */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_base     Core Definitions
+  \brief      Definitions for base addresses, unions, and structures.
+  @{
+ */
+
+/* Memory mapping of Core Hardware */
+#define SCS_BASE            (0xE000E000UL)                            /*!< System Control Space Base Address */
+#define SysTick_BASE        (SCS_BASE +  0x0010UL)                    /*!< SysTick Base Address */
+#define NVIC_BASE           (SCS_BASE +  0x0100UL)                    /*!< NVIC Base Address */
+#define SCB_BASE            (SCS_BASE +  0x0D00UL)                    /*!< System Control Block Base Address */
+
+#define SCB                 ((SCB_Type       *)     SCB_BASE      )   /*!< SCB configuration struct */
+#define SysTick             ((SysTick_Type   *)     SysTick_BASE  )   /*!< SysTick configuration struct */
+#define NVIC                ((NVIC_Type      *)     NVIC_BASE     )   /*!< NVIC configuration struct */
+
+
+/*@} */
+
+
+
+/*******************************************************************************
+ *                Hardware Abstraction Layer
+  Core Function Interface contains:
+  - Core NVIC Functions
+  - Core SysTick Functions
+  - Core Register Access Functions
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference
+*/
+
+
+
+/* ##########################   NVIC functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_NVICFunctions NVIC Functions
+  \brief    Functions that manage interrupts and exceptions via the NVIC.
+  @{
+ */
+
+#ifdef CMSIS_NVIC_VIRTUAL
+  #ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE
+    #define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h"
+  #endif
+  #include CMSIS_NVIC_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetPriorityGrouping    __NVIC_SetPriorityGrouping
+  #define NVIC_GetPriorityGrouping    __NVIC_GetPriorityGrouping
+  #define NVIC_EnableIRQ              __NVIC_EnableIRQ
+  #define NVIC_GetEnableIRQ           __NVIC_GetEnableIRQ
+  #define NVIC_DisableIRQ             __NVIC_DisableIRQ
+  #define NVIC_GetPendingIRQ          __NVIC_GetPendingIRQ
+  #define NVIC_SetPendingIRQ          __NVIC_SetPendingIRQ
+  #define NVIC_ClearPendingIRQ        __NVIC_ClearPendingIRQ
+/*#define NVIC_GetActive              __NVIC_GetActive             not available for Cortex-M0 */
+  #define NVIC_SetPriority            __NVIC_SetPriority
+  #define NVIC_GetPriority            __NVIC_GetPriority
+  #define NVIC_SystemReset            __NVIC_SystemReset
+#endif /* CMSIS_NVIC_VIRTUAL */
+
+#ifdef CMSIS_VECTAB_VIRTUAL
+  #ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+    #define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h"
+  #endif
+  #include CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetVector              __NVIC_SetVector
+  #define NVIC_GetVector              __NVIC_GetVector
+#endif  /* (CMSIS_VECTAB_VIRTUAL) */
+
+#define NVIC_USER_IRQ_OFFSET          16
+
+
+/* The following EXC_RETURN values are saved the LR on exception entry */
+#define EXC_RETURN_HANDLER         (0xFFFFFFF1UL)     /* return to Handler mode, uses MSP after return                               */
+#define EXC_RETURN_THREAD_MSP      (0xFFFFFFF9UL)     /* return to Thread mode, uses MSP after return                                */
+#define EXC_RETURN_THREAD_PSP      (0xFFFFFFFDUL)     /* return to Thread mode, uses PSP after return                                */
+
+
+/* Interrupt Priorities are WORD accessible only under Armv6-M                  */
+/* The following MACROS handle generation of the register offset and byte masks */
+#define _BIT_SHIFT(IRQn)         (  ((((uint32_t)(int32_t)(IRQn))         )      &  0x03UL) * 8UL)
+#define _SHP_IDX(IRQn)           ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >>    2UL)      )
+#define _IP_IDX(IRQn)            (   (((uint32_t)(int32_t)(IRQn))                >>    2UL)      )
+
+#define __NVIC_SetPriorityGrouping(X) (void)(X)
+#define __NVIC_GetPriorityGrouping()  (0U)
+
+/**
+  \brief   Enable Interrupt
+  \details Enables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Enable status
+  \details Returns a device specific interrupt enable status from the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt is not enabled.
+  \return             1  Interrupt is enabled.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Disable Interrupt
+  \details Disables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+    __DSB();
+    __ISB();
+  }
+}
+
+
+/**
+  \brief   Get Pending Interrupt
+  \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt status is not pending.
+  \return             1  Interrupt status is pending.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Set Pending Interrupt
+  \details Sets the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Clear Pending Interrupt
+  \details Clears the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Set Interrupt Priority
+  \details Sets the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]      IRQn  Interrupt number.
+  \param [in]  priority  Priority to set.
+  \note    The priority cannot be set for every processor exception.
+ */
+__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->IP[_IP_IDX(IRQn)]  = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)]  & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+  else
+  {
+    SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Priority
+  \details Reads the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn  Interrupt number.
+  \return             Interrupt Priority.
+                      Value is aligned automatically to the implemented priority bits of the microcontroller.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn)
+{
+
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+  else
+  {
+    return((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+}
+
+
+/**
+  \brief   Encode Priority
+  \details Encodes the priority for an interrupt with the given priority group,
+           preemptive priority value, and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set.
+  \param [in]     PriorityGroup  Used priority group.
+  \param [in]   PreemptPriority  Preemptive priority value (starting from 0).
+  \param [in]       SubPriority  Subpriority value (starting from 0).
+  \return                        Encoded priority. Value can be used in the function \ref NVIC_SetPriority().
+ */
+__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  return (
+           ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) |
+           ((SubPriority     & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL)))
+         );
+}
+
+
+/**
+  \brief   Decode Priority
+  \details Decodes an interrupt priority value with a given priority group to
+           preemptive priority value and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set.
+  \param [in]         Priority   Priority value, which can be retrieved with the function \ref NVIC_GetPriority().
+  \param [in]     PriorityGroup  Used priority group.
+  \param [out] pPreemptPriority  Preemptive priority value (starting from 0).
+  \param [out]     pSubPriority  Subpriority value (starting from 0).
+ */
+__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL);
+  *pSubPriority     = (Priority                   ) & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL);
+}
+
+
+
+/**
+  \brief   Set Interrupt Vector
+  \details Sets an interrupt vector in SRAM based interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+           Address 0 must be mapped to SRAM.
+  \param [in]   IRQn      Interrupt number
+  \param [in]   vector    Address of interrupt handler function
+ */
+__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector;
+}
+
+
+/**
+  \brief   Get Interrupt Vector
+  \details Reads an interrupt vector from interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn      Interrupt number.
+  \return                 Address of interrupt handler function
+ */
+__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET];
+}
+
+
+/**
+  \brief   System Reset
+  \details Initiates a system reset request to reset the MCU.
+ */
+__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void)
+{
+  __DSB();                                                          /* Ensure all outstanding memory accesses included
+                                                                       buffered write are completed before reset */
+  SCB->AIRCR  = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) |
+                 SCB_AIRCR_SYSRESETREQ_Msk);
+  __DSB();                                                          /* Ensure completion of memory access */
+
+  for(;;)                                                           /* wait until reset */
+  {
+    __NOP();
+  }
+}
+
+/*@} end of CMSIS_Core_NVICFunctions */
+
+
+/* ##########################  FPU functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_FpuFunctions FPU Functions
+  \brief    Function that provides FPU type.
+  @{
+ */
+
+/**
+  \brief   get FPU type
+  \details returns the FPU type
+  \returns
+   - \b  0: No FPU
+   - \b  1: Single precision FPU
+   - \b  2: Double + Single precision FPU
+ */
+__STATIC_INLINE uint32_t SCB_GetFPUType(void)
+{
+    return 0U;           /* No FPU */
+}
+
+
+/*@} end of CMSIS_Core_FpuFunctions */
+
+
+
+/* ##################################    SysTick function  ############################################ */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_SysTickFunctions SysTick Functions
+  \brief    Functions that configure the System.
+  @{
+ */
+
+#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U)
+
+/**
+  \brief   System Tick Configuration
+  \details Initializes the System Timer and its interrupt, and starts the System Tick Timer.
+           Counter is in free running mode to generate periodic interrupts.
+  \param [in]  ticks  Number of ticks between two interrupts.
+  \return          0  Function succeeded.
+  \return          1  Function failed.
+  \note    When the variable <b>__Vendor_SysTickConfig</b> is set to 1, then the
+           function <b>SysTick_Config</b> is not included. In this case, the file <b><i>device</i>.h</b>
+           must contain a vendor-specific implementation of this function.
+ */
+__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks)
+{
+  if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk)
+  {
+    return (1UL);                                                   /* Reload value impossible */
+  }
+
+  SysTick->LOAD  = (uint32_t)(ticks - 1UL);                         /* set reload register */
+  NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */
+  SysTick->VAL   = 0UL;                                             /* Load the SysTick Counter Value */
+  SysTick->CTRL  = SysTick_CTRL_CLKSOURCE_Msk |
+                   SysTick_CTRL_TICKINT_Msk   |
+                   SysTick_CTRL_ENABLE_Msk;                         /* Enable SysTick IRQ and SysTick Timer */
+  return (0UL);                                                     /* Function successful */
+}
+
+#endif
+
+/*@} end of CMSIS_Core_SysTickFunctions */
+
+
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM0_H_DEPENDANT */
+
+#endif /* __CMSIS_GENERIC */

fw_hal/Drivers/CMSIS/Include/core_cm1.h

@@ -0,0 +1,976 @@
+/**************************************************************************//**
+ * @file     core_cm1.h
+ * @brief    CMSIS Cortex-M1 Core Peripheral Access Layer Header File
+ * @version  V1.0.0
+ * @date     23. July 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CORE_CM1_H_GENERIC
+#define __CORE_CM1_H_GENERIC
+
+#include <stdint.h>
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/**
+  \page CMSIS_MISRA_Exceptions  MISRA-C:2004 Compliance Exceptions
+  CMSIS violates the following MISRA-C:2004 rules:
+
+   \li Required Rule 8.5, object/function definition in header file.<br>
+     Function definitions in header files are used to allow 'inlining'.
+
+   \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.<br>
+     Unions are used for effective representation of core registers.
+
+   \li Advisory Rule 19.7, Function-like macro defined.<br>
+     Function-like macros are used to allow more efficient code.
+ */
+
+
+/*******************************************************************************
+ *                 CMSIS definitions
+ ******************************************************************************/
+/**
+  \ingroup Cortex_M1
+  @{
+ */
+
+#include "cmsis_version.h"
+ 
+/*  CMSIS CM1 definitions */
+#define __CM1_CMSIS_VERSION_MAIN  (__CM_CMSIS_VERSION_MAIN)              /*!< \deprecated [31:16] CMSIS HAL main version */
+#define __CM1_CMSIS_VERSION_SUB   (__CM_CMSIS_VERSION_SUB)               /*!< \deprecated [15:0]  CMSIS HAL sub version */
+#define __CM1_CMSIS_VERSION       ((__CM1_CMSIS_VERSION_MAIN << 16U) | \
+                                    __CM1_CMSIS_VERSION_SUB           )  /*!< \deprecated CMSIS HAL version number */
+
+#define __CORTEX_M                (1U)                                   /*!< Cortex-M Core */
+
+/** __FPU_USED indicates whether an FPU is used or not.
+    This core does not support an FPU at all
+*/
+#define __FPU_USED       0U
+
+#if defined ( __CC_ARM )
+  #if defined __TARGET_FPU_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #if defined __ARM_PCS_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __GNUC__ )
+  #if defined (__VFP_FP__) && !defined(__SOFTFP__)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __ICCARM__ )
+  #if defined __ARMVFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TI_ARM__ )
+  #if defined __TI_VFP_SUPPORT__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TASKING__ )
+  #if defined __FPU_VFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __CSMC__ )
+  #if ( __CSMC__ & 0x400U)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#endif
+
+#include "cmsis_compiler.h"               /* CMSIS compiler specific defines */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM1_H_GENERIC */
+
+#ifndef __CMSIS_GENERIC
+
+#ifndef __CORE_CM1_H_DEPENDANT
+#define __CORE_CM1_H_DEPENDANT
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* check device defines and use defaults */
+#if defined __CHECK_DEVICE_DEFINES
+  #ifndef __CM1_REV
+    #define __CM1_REV               0x0100U
+    #warning "__CM1_REV not defined in device header file; using default!"
+  #endif
+
+  #ifndef __NVIC_PRIO_BITS
+    #define __NVIC_PRIO_BITS          2U
+    #warning "__NVIC_PRIO_BITS not defined in device header file; using default!"
+  #endif
+
+  #ifndef __Vendor_SysTickConfig
+    #define __Vendor_SysTickConfig    0U
+    #warning "__Vendor_SysTickConfig not defined in device header file; using default!"
+  #endif
+#endif
+
+/* IO definitions (access restrictions to peripheral registers) */
+/**
+    \defgroup CMSIS_glob_defs CMSIS Global Defines
+
+    <strong>IO Type Qualifiers</strong> are used
+    \li to specify the access to peripheral variables.
+    \li for automatic generation of peripheral register debug information.
+*/
+#ifdef __cplusplus
+  #define   __I     volatile             /*!< Defines 'read only' permissions */
+#else
+  #define   __I     volatile const       /*!< Defines 'read only' permissions */
+#endif
+#define     __O     volatile             /*!< Defines 'write only' permissions */
+#define     __IO    volatile             /*!< Defines 'read / write' permissions */
+
+/* following defines should be used for structure members */
+#define     __IM     volatile const      /*! Defines 'read only' structure member permissions */
+#define     __OM     volatile            /*! Defines 'write only' structure member permissions */
+#define     __IOM    volatile            /*! Defines 'read / write' structure member permissions */
+
+/*@} end of group Cortex_M1 */
+
+
+
+/*******************************************************************************
+ *                 Register Abstraction
+  Core Register contain:
+  - Core Register
+  - Core NVIC Register
+  - Core SCB Register
+  - Core SysTick Register
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_core_register Defines and Type Definitions
+  \brief Type definitions and defines for Cortex-M processor based devices.
+*/
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_CORE  Status and Control Registers
+  \brief      Core Register type definitions.
+  @{
+ */
+
+/**
+  \brief  Union type to access the Application Program Status Register (APSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:28;              /*!< bit:  0..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} APSR_Type;
+
+/* APSR Register Definitions */
+#define APSR_N_Pos                         31U                                            /*!< APSR: N Position */
+#define APSR_N_Msk                         (1UL << APSR_N_Pos)                            /*!< APSR: N Mask */
+
+#define APSR_Z_Pos                         30U                                            /*!< APSR: Z Position */
+#define APSR_Z_Msk                         (1UL << APSR_Z_Pos)                            /*!< APSR: Z Mask */
+
+#define APSR_C_Pos                         29U                                            /*!< APSR: C Position */
+#define APSR_C_Msk                         (1UL << APSR_C_Pos)                            /*!< APSR: C Mask */
+
+#define APSR_V_Pos                         28U                                            /*!< APSR: V Position */
+#define APSR_V_Msk                         (1UL << APSR_V_Pos)                            /*!< APSR: V Mask */
+
+
+/**
+  \brief  Union type to access the Interrupt Program Status Register (IPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:23;              /*!< bit:  9..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} IPSR_Type;
+
+/* IPSR Register Definitions */
+#define IPSR_ISR_Pos                        0U                                            /*!< IPSR: ISR Position */
+#define IPSR_ISR_Msk                       (0x1FFUL /*<< IPSR_ISR_Pos*/)                  /*!< IPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Special-Purpose Program Status Registers (xPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:15;              /*!< bit:  9..23  Reserved */
+    uint32_t T:1;                        /*!< bit:     24  Thumb bit        (read 0) */
+    uint32_t _reserved1:3;               /*!< bit: 25..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} xPSR_Type;
+
+/* xPSR Register Definitions */
+#define xPSR_N_Pos                         31U                                            /*!< xPSR: N Position */
+#define xPSR_N_Msk                         (1UL << xPSR_N_Pos)                            /*!< xPSR: N Mask */
+
+#define xPSR_Z_Pos                         30U                                            /*!< xPSR: Z Position */
+#define xPSR_Z_Msk                         (1UL << xPSR_Z_Pos)                            /*!< xPSR: Z Mask */
+
+#define xPSR_C_Pos                         29U                                            /*!< xPSR: C Position */
+#define xPSR_C_Msk                         (1UL << xPSR_C_Pos)                            /*!< xPSR: C Mask */
+
+#define xPSR_V_Pos                         28U                                            /*!< xPSR: V Position */
+#define xPSR_V_Msk                         (1UL << xPSR_V_Pos)                            /*!< xPSR: V Mask */
+
+#define xPSR_T_Pos                         24U                                            /*!< xPSR: T Position */
+#define xPSR_T_Msk                         (1UL << xPSR_T_Pos)                            /*!< xPSR: T Mask */
+
+#define xPSR_ISR_Pos                        0U                                            /*!< xPSR: ISR Position */
+#define xPSR_ISR_Msk                       (0x1FFUL /*<< xPSR_ISR_Pos*/)                  /*!< xPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Control Registers (CONTROL).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:1;               /*!< bit:      0  Reserved */
+    uint32_t SPSEL:1;                    /*!< bit:      1  Stack to be used */
+    uint32_t _reserved1:30;              /*!< bit:  2..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} CONTROL_Type;
+
+/* CONTROL Register Definitions */
+#define CONTROL_SPSEL_Pos                   1U                                            /*!< CONTROL: SPSEL Position */
+#define CONTROL_SPSEL_Msk                  (1UL << CONTROL_SPSEL_Pos)                     /*!< CONTROL: SPSEL Mask */
+
+/*@} end of group CMSIS_CORE */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_NVIC  Nested Vectored Interrupt Controller (NVIC)
+  \brief      Type definitions for the NVIC Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the Nested Vectored Interrupt Controller (NVIC).
+ */
+typedef struct
+{
+  __IOM uint32_t ISER[1U];               /*!< Offset: 0x000 (R/W)  Interrupt Set Enable Register */
+        uint32_t RESERVED0[31U];
+  __IOM uint32_t ICER[1U];               /*!< Offset: 0x080 (R/W)  Interrupt Clear Enable Register */
+        uint32_t RSERVED1[31U];
+  __IOM uint32_t ISPR[1U];               /*!< Offset: 0x100 (R/W)  Interrupt Set Pending Register */
+        uint32_t RESERVED2[31U];
+  __IOM uint32_t ICPR[1U];               /*!< Offset: 0x180 (R/W)  Interrupt Clear Pending Register */
+        uint32_t RESERVED3[31U];
+        uint32_t RESERVED4[64U];
+  __IOM uint32_t IP[8U];                 /*!< Offset: 0x300 (R/W)  Interrupt Priority Register */
+}  NVIC_Type;
+
+/*@} end of group CMSIS_NVIC */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCB     System Control Block (SCB)
+  \brief    Type definitions for the System Control Block Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control Block (SCB).
+ */
+typedef struct
+{
+  __IM  uint32_t CPUID;                  /*!< Offset: 0x000 (R/ )  CPUID Base Register */
+  __IOM uint32_t ICSR;                   /*!< Offset: 0x004 (R/W)  Interrupt Control and State Register */
+        uint32_t RESERVED0;
+  __IOM uint32_t AIRCR;                  /*!< Offset: 0x00C (R/W)  Application Interrupt and Reset Control Register */
+  __IOM uint32_t SCR;                    /*!< Offset: 0x010 (R/W)  System Control Register */
+  __IOM uint32_t CCR;                    /*!< Offset: 0x014 (R/W)  Configuration Control Register */
+        uint32_t RESERVED1;
+  __IOM uint32_t SHP[2U];                /*!< Offset: 0x01C (R/W)  System Handlers Priority Registers. [0] is RESERVED */
+  __IOM uint32_t SHCSR;                  /*!< Offset: 0x024 (R/W)  System Handler Control and State Register */
+} SCB_Type;
+
+/* SCB CPUID Register Definitions */
+#define SCB_CPUID_IMPLEMENTER_Pos          24U                                            /*!< SCB CPUID: IMPLEMENTER Position */
+#define SCB_CPUID_IMPLEMENTER_Msk          (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos)          /*!< SCB CPUID: IMPLEMENTER Mask */
+
+#define SCB_CPUID_VARIANT_Pos              20U                                            /*!< SCB CPUID: VARIANT Position */
+#define SCB_CPUID_VARIANT_Msk              (0xFUL << SCB_CPUID_VARIANT_Pos)               /*!< SCB CPUID: VARIANT Mask */
+
+#define SCB_CPUID_ARCHITECTURE_Pos         16U                                            /*!< SCB CPUID: ARCHITECTURE Position */
+#define SCB_CPUID_ARCHITECTURE_Msk         (0xFUL << SCB_CPUID_ARCHITECTURE_Pos)          /*!< SCB CPUID: ARCHITECTURE Mask */
+
+#define SCB_CPUID_PARTNO_Pos                4U                                            /*!< SCB CPUID: PARTNO Position */
+#define SCB_CPUID_PARTNO_Msk               (0xFFFUL << SCB_CPUID_PARTNO_Pos)              /*!< SCB CPUID: PARTNO Mask */
+
+#define SCB_CPUID_REVISION_Pos              0U                                            /*!< SCB CPUID: REVISION Position */
+#define SCB_CPUID_REVISION_Msk             (0xFUL /*<< SCB_CPUID_REVISION_Pos*/)          /*!< SCB CPUID: REVISION Mask */
+
+/* SCB Interrupt Control State Register Definitions */
+#define SCB_ICSR_NMIPENDSET_Pos            31U                                            /*!< SCB ICSR: NMIPENDSET Position */
+#define SCB_ICSR_NMIPENDSET_Msk            (1UL << SCB_ICSR_NMIPENDSET_Pos)               /*!< SCB ICSR: NMIPENDSET Mask */
+
+#define SCB_ICSR_PENDSVSET_Pos             28U                                            /*!< SCB ICSR: PENDSVSET Position */
+#define SCB_ICSR_PENDSVSET_Msk             (1UL << SCB_ICSR_PENDSVSET_Pos)                /*!< SCB ICSR: PENDSVSET Mask */
+
+#define SCB_ICSR_PENDSVCLR_Pos             27U                                            /*!< SCB ICSR: PENDSVCLR Position */
+#define SCB_ICSR_PENDSVCLR_Msk             (1UL << SCB_ICSR_PENDSVCLR_Pos)                /*!< SCB ICSR: PENDSVCLR Mask */
+
+#define SCB_ICSR_PENDSTSET_Pos             26U                                            /*!< SCB ICSR: PENDSTSET Position */
+#define SCB_ICSR_PENDSTSET_Msk             (1UL << SCB_ICSR_PENDSTSET_Pos)                /*!< SCB ICSR: PENDSTSET Mask */
+
+#define SCB_ICSR_PENDSTCLR_Pos             25U                                            /*!< SCB ICSR: PENDSTCLR Position */
+#define SCB_ICSR_PENDSTCLR_Msk             (1UL << SCB_ICSR_PENDSTCLR_Pos)                /*!< SCB ICSR: PENDSTCLR Mask */
+
+#define SCB_ICSR_ISRPREEMPT_Pos            23U                                            /*!< SCB ICSR: ISRPREEMPT Position */
+#define SCB_ICSR_ISRPREEMPT_Msk            (1UL << SCB_ICSR_ISRPREEMPT_Pos)               /*!< SCB ICSR: ISRPREEMPT Mask */
+
+#define SCB_ICSR_ISRPENDING_Pos            22U                                            /*!< SCB ICSR: ISRPENDING Position */
+#define SCB_ICSR_ISRPENDING_Msk            (1UL << SCB_ICSR_ISRPENDING_Pos)               /*!< SCB ICSR: ISRPENDING Mask */
+
+#define SCB_ICSR_VECTPENDING_Pos           12U                                            /*!< SCB ICSR: VECTPENDING Position */
+#define SCB_ICSR_VECTPENDING_Msk           (0x1FFUL << SCB_ICSR_VECTPENDING_Pos)          /*!< SCB ICSR: VECTPENDING Mask */
+
+#define SCB_ICSR_VECTACTIVE_Pos             0U                                            /*!< SCB ICSR: VECTACTIVE Position */
+#define SCB_ICSR_VECTACTIVE_Msk            (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/)       /*!< SCB ICSR: VECTACTIVE Mask */
+
+/* SCB Application Interrupt and Reset Control Register Definitions */
+#define SCB_AIRCR_VECTKEY_Pos              16U                                            /*!< SCB AIRCR: VECTKEY Position */
+#define SCB_AIRCR_VECTKEY_Msk              (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos)            /*!< SCB AIRCR: VECTKEY Mask */
+
+#define SCB_AIRCR_VECTKEYSTAT_Pos          16U                                            /*!< SCB AIRCR: VECTKEYSTAT Position */
+#define SCB_AIRCR_VECTKEYSTAT_Msk          (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos)        /*!< SCB AIRCR: VECTKEYSTAT Mask */
+
+#define SCB_AIRCR_ENDIANESS_Pos            15U                                            /*!< SCB AIRCR: ENDIANESS Position */
+#define SCB_AIRCR_ENDIANESS_Msk            (1UL << SCB_AIRCR_ENDIANESS_Pos)               /*!< SCB AIRCR: ENDIANESS Mask */
+
+#define SCB_AIRCR_SYSRESETREQ_Pos           2U                                            /*!< SCB AIRCR: SYSRESETREQ Position */
+#define SCB_AIRCR_SYSRESETREQ_Msk          (1UL << SCB_AIRCR_SYSRESETREQ_Pos)             /*!< SCB AIRCR: SYSRESETREQ Mask */
+
+#define SCB_AIRCR_VECTCLRACTIVE_Pos         1U                                            /*!< SCB AIRCR: VECTCLRACTIVE Position */
+#define SCB_AIRCR_VECTCLRACTIVE_Msk        (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos)           /*!< SCB AIRCR: VECTCLRACTIVE Mask */
+
+/* SCB System Control Register Definitions */
+#define SCB_SCR_SEVONPEND_Pos               4U                                            /*!< SCB SCR: SEVONPEND Position */
+#define SCB_SCR_SEVONPEND_Msk              (1UL << SCB_SCR_SEVONPEND_Pos)                 /*!< SCB SCR: SEVONPEND Mask */
+
+#define SCB_SCR_SLEEPDEEP_Pos               2U                                            /*!< SCB SCR: SLEEPDEEP Position */
+#define SCB_SCR_SLEEPDEEP_Msk              (1UL << SCB_SCR_SLEEPDEEP_Pos)                 /*!< SCB SCR: SLEEPDEEP Mask */
+
+#define SCB_SCR_SLEEPONEXIT_Pos             1U                                            /*!< SCB SCR: SLEEPONEXIT Position */
+#define SCB_SCR_SLEEPONEXIT_Msk            (1UL << SCB_SCR_SLEEPONEXIT_Pos)               /*!< SCB SCR: SLEEPONEXIT Mask */
+
+/* SCB Configuration Control Register Definitions */
+#define SCB_CCR_STKALIGN_Pos                9U                                            /*!< SCB CCR: STKALIGN Position */
+#define SCB_CCR_STKALIGN_Msk               (1UL << SCB_CCR_STKALIGN_Pos)                  /*!< SCB CCR: STKALIGN Mask */
+
+#define SCB_CCR_UNALIGN_TRP_Pos             3U                                            /*!< SCB CCR: UNALIGN_TRP Position */
+#define SCB_CCR_UNALIGN_TRP_Msk            (1UL << SCB_CCR_UNALIGN_TRP_Pos)               /*!< SCB CCR: UNALIGN_TRP Mask */
+
+/* SCB System Handler Control and State Register Definitions */
+#define SCB_SHCSR_SVCALLPENDED_Pos         15U                                            /*!< SCB SHCSR: SVCALLPENDED Position */
+#define SCB_SHCSR_SVCALLPENDED_Msk         (1UL << SCB_SHCSR_SVCALLPENDED_Pos)            /*!< SCB SHCSR: SVCALLPENDED Mask */
+
+/*@} end of group CMSIS_SCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCnSCB System Controls not in SCB (SCnSCB)
+  \brief    Type definitions for the System Control and ID Register not in the SCB
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control and ID Register not in the SCB.
+ */
+typedef struct
+{
+        uint32_t RESERVED0[2U];
+  __IOM uint32_t ACTLR;                  /*!< Offset: 0x008 (R/W)  Auxiliary Control Register */
+} SCnSCB_Type;
+
+/* Auxiliary Control Register Definitions */
+#define SCnSCB_ACTLR_ITCMUAEN_Pos            4U                                        /*!< ACTLR: Instruction TCM Upper Alias Enable Position */
+#define SCnSCB_ACTLR_ITCMUAEN_Msk           (1UL << SCnSCB_ACTLR_ITCMUAEN_Pos)         /*!< ACTLR: Instruction TCM Upper Alias Enable Mask */
+
+#define SCnSCB_ACTLR_ITCMLAEN_Pos            3U                                        /*!< ACTLR: Instruction TCM Lower Alias Enable Position */
+#define SCnSCB_ACTLR_ITCMLAEN_Msk           (1UL << SCnSCB_ACTLR_ITCMLAEN_Pos)         /*!< ACTLR: Instruction TCM Lower Alias Enable Mask */
+
+/*@} end of group CMSIS_SCnotSCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SysTick     System Tick Timer (SysTick)
+  \brief    Type definitions for the System Timer Registers.
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Timer (SysTick).
+ */
+typedef struct
+{
+  __IOM uint32_t CTRL;                   /*!< Offset: 0x000 (R/W)  SysTick Control and Status Register */
+  __IOM uint32_t LOAD;                   /*!< Offset: 0x004 (R/W)  SysTick Reload Value Register */
+  __IOM uint32_t VAL;                    /*!< Offset: 0x008 (R/W)  SysTick Current Value Register */
+  __IM  uint32_t CALIB;                  /*!< Offset: 0x00C (R/ )  SysTick Calibration Register */
+} SysTick_Type;
+
+/* SysTick Control / Status Register Definitions */
+#define SysTick_CTRL_COUNTFLAG_Pos         16U                                            /*!< SysTick CTRL: COUNTFLAG Position */
+#define SysTick_CTRL_COUNTFLAG_Msk         (1UL << SysTick_CTRL_COUNTFLAG_Pos)            /*!< SysTick CTRL: COUNTFLAG Mask */
+
+#define SysTick_CTRL_CLKSOURCE_Pos          2U                                            /*!< SysTick CTRL: CLKSOURCE Position */
+#define SysTick_CTRL_CLKSOURCE_Msk         (1UL << SysTick_CTRL_CLKSOURCE_Pos)            /*!< SysTick CTRL: CLKSOURCE Mask */
+
+#define SysTick_CTRL_TICKINT_Pos            1U                                            /*!< SysTick CTRL: TICKINT Position */
+#define SysTick_CTRL_TICKINT_Msk           (1UL << SysTick_CTRL_TICKINT_Pos)              /*!< SysTick CTRL: TICKINT Mask */
+
+#define SysTick_CTRL_ENABLE_Pos             0U                                            /*!< SysTick CTRL: ENABLE Position */
+#define SysTick_CTRL_ENABLE_Msk            (1UL /*<< SysTick_CTRL_ENABLE_Pos*/)           /*!< SysTick CTRL: ENABLE Mask */
+
+/* SysTick Reload Register Definitions */
+#define SysTick_LOAD_RELOAD_Pos             0U                                            /*!< SysTick LOAD: RELOAD Position */
+#define SysTick_LOAD_RELOAD_Msk            (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/)    /*!< SysTick LOAD: RELOAD Mask */
+
+/* SysTick Current Register Definitions */
+#define SysTick_VAL_CURRENT_Pos             0U                                            /*!< SysTick VAL: CURRENT Position */
+#define SysTick_VAL_CURRENT_Msk            (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/)    /*!< SysTick VAL: CURRENT Mask */
+
+/* SysTick Calibration Register Definitions */
+#define SysTick_CALIB_NOREF_Pos            31U                                            /*!< SysTick CALIB: NOREF Position */
+#define SysTick_CALIB_NOREF_Msk            (1UL << SysTick_CALIB_NOREF_Pos)               /*!< SysTick CALIB: NOREF Mask */
+
+#define SysTick_CALIB_SKEW_Pos             30U                                            /*!< SysTick CALIB: SKEW Position */
+#define SysTick_CALIB_SKEW_Msk             (1UL << SysTick_CALIB_SKEW_Pos)                /*!< SysTick CALIB: SKEW Mask */
+
+#define SysTick_CALIB_TENMS_Pos             0U                                            /*!< SysTick CALIB: TENMS Position */
+#define SysTick_CALIB_TENMS_Msk            (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/)    /*!< SysTick CALIB: TENMS Mask */
+
+/*@} end of group CMSIS_SysTick */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_CoreDebug       Core Debug Registers (CoreDebug)
+  \brief    Cortex-M1 Core Debug Registers (DCB registers, SHCSR, and DFSR) are only accessible over DAP and not via processor.
+            Therefore they are not covered by the Cortex-M1 header file.
+  @{
+ */
+/*@} end of group CMSIS_CoreDebug */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_bitfield     Core register bit field macros
+  \brief      Macros for use with bit field definitions (xxx_Pos, xxx_Msk).
+  @{
+ */
+
+/**
+  \brief   Mask and shift a bit field value for use in a register bit range.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of the bit field. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted value.
+*/
+#define _VAL2FLD(field, value)    (((uint32_t)(value) << field ## _Pos) & field ## _Msk)
+
+/**
+  \brief     Mask and shift a register value to extract a bit filed value.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of register. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted bit field value.
+*/
+#define _FLD2VAL(field, value)    (((uint32_t)(value) & field ## _Msk) >> field ## _Pos)
+
+/*@} end of group CMSIS_core_bitfield */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_base     Core Definitions
+  \brief      Definitions for base addresses, unions, and structures.
+  @{
+ */
+
+/* Memory mapping of Core Hardware */
+#define SCS_BASE            (0xE000E000UL)                            /*!< System Control Space Base Address */
+#define SysTick_BASE        (SCS_BASE +  0x0010UL)                    /*!< SysTick Base Address */
+#define NVIC_BASE           (SCS_BASE +  0x0100UL)                    /*!< NVIC Base Address */
+#define SCB_BASE            (SCS_BASE +  0x0D00UL)                    /*!< System Control Block Base Address */
+
+#define SCnSCB              ((SCnSCB_Type    *)     SCS_BASE      )   /*!< System control Register not in SCB */
+#define SCB                 ((SCB_Type       *)     SCB_BASE      )   /*!< SCB configuration struct */
+#define SysTick             ((SysTick_Type   *)     SysTick_BASE  )   /*!< SysTick configuration struct */
+#define NVIC                ((NVIC_Type      *)     NVIC_BASE     )   /*!< NVIC configuration struct */
+
+
+/*@} */
+
+
+
+/*******************************************************************************
+ *                Hardware Abstraction Layer
+  Core Function Interface contains:
+  - Core NVIC Functions
+  - Core SysTick Functions
+  - Core Register Access Functions
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference
+*/
+
+
+
+/* ##########################   NVIC functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_NVICFunctions NVIC Functions
+  \brief    Functions that manage interrupts and exceptions via the NVIC.
+  @{
+ */
+
+#ifdef CMSIS_NVIC_VIRTUAL
+  #ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE
+    #define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h"
+  #endif
+  #include CMSIS_NVIC_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetPriorityGrouping    __NVIC_SetPriorityGrouping
+  #define NVIC_GetPriorityGrouping    __NVIC_GetPriorityGrouping
+  #define NVIC_EnableIRQ              __NVIC_EnableIRQ
+  #define NVIC_GetEnableIRQ           __NVIC_GetEnableIRQ
+  #define NVIC_DisableIRQ             __NVIC_DisableIRQ
+  #define NVIC_GetPendingIRQ          __NVIC_GetPendingIRQ
+  #define NVIC_SetPendingIRQ          __NVIC_SetPendingIRQ
+  #define NVIC_ClearPendingIRQ        __NVIC_ClearPendingIRQ
+/*#define NVIC_GetActive              __NVIC_GetActive             not available for Cortex-M1 */
+  #define NVIC_SetPriority            __NVIC_SetPriority
+  #define NVIC_GetPriority            __NVIC_GetPriority
+  #define NVIC_SystemReset            __NVIC_SystemReset
+#endif /* CMSIS_NVIC_VIRTUAL */
+
+#ifdef CMSIS_VECTAB_VIRTUAL
+  #ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+    #define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h"
+  #endif
+  #include CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetVector              __NVIC_SetVector
+  #define NVIC_GetVector              __NVIC_GetVector
+#endif  /* (CMSIS_VECTAB_VIRTUAL) */
+
+#define NVIC_USER_IRQ_OFFSET          16
+
+
+/* The following EXC_RETURN values are saved the LR on exception entry */
+#define EXC_RETURN_HANDLER         (0xFFFFFFF1UL)     /* return to Handler mode, uses MSP after return                               */
+#define EXC_RETURN_THREAD_MSP      (0xFFFFFFF9UL)     /* return to Thread mode, uses MSP after return                                */
+#define EXC_RETURN_THREAD_PSP      (0xFFFFFFFDUL)     /* return to Thread mode, uses PSP after return                                */
+
+
+/* Interrupt Priorities are WORD accessible only under Armv6-M                  */
+/* The following MACROS handle generation of the register offset and byte masks */
+#define _BIT_SHIFT(IRQn)         (  ((((uint32_t)(int32_t)(IRQn))         )      &  0x03UL) * 8UL)
+#define _SHP_IDX(IRQn)           ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >>    2UL)      )
+#define _IP_IDX(IRQn)            (   (((uint32_t)(int32_t)(IRQn))                >>    2UL)      )
+
+#define __NVIC_SetPriorityGrouping(X) (void)(X)
+#define __NVIC_GetPriorityGrouping()  (0U)
+
+/**
+  \brief   Enable Interrupt
+  \details Enables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Enable status
+  \details Returns a device specific interrupt enable status from the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt is not enabled.
+  \return             1  Interrupt is enabled.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Disable Interrupt
+  \details Disables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+    __DSB();
+    __ISB();
+  }
+}
+
+
+/**
+  \brief   Get Pending Interrupt
+  \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt status is not pending.
+  \return             1  Interrupt status is pending.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Set Pending Interrupt
+  \details Sets the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Clear Pending Interrupt
+  \details Clears the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Set Interrupt Priority
+  \details Sets the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]      IRQn  Interrupt number.
+  \param [in]  priority  Priority to set.
+  \note    The priority cannot be set for every processor exception.
+ */
+__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->IP[_IP_IDX(IRQn)]  = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)]  & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+  else
+  {
+    SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Priority
+  \details Reads the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn  Interrupt number.
+  \return             Interrupt Priority.
+                      Value is aligned automatically to the implemented priority bits of the microcontroller.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn)
+{
+
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+  else
+  {
+    return((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+}
+
+
+/**
+  \brief   Encode Priority
+  \details Encodes the priority for an interrupt with the given priority group,
+           preemptive priority value, and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set.
+  \param [in]     PriorityGroup  Used priority group.
+  \param [in]   PreemptPriority  Preemptive priority value (starting from 0).
+  \param [in]       SubPriority  Subpriority value (starting from 0).
+  \return                        Encoded priority. Value can be used in the function \ref NVIC_SetPriority().
+ */
+__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  return (
+           ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) |
+           ((SubPriority     & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL)))
+         );
+}
+
+
+/**
+  \brief   Decode Priority
+  \details Decodes an interrupt priority value with a given priority group to
+           preemptive priority value and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set.
+  \param [in]         Priority   Priority value, which can be retrieved with the function \ref NVIC_GetPriority().
+  \param [in]     PriorityGroup  Used priority group.
+  \param [out] pPreemptPriority  Preemptive priority value (starting from 0).
+  \param [out]     pSubPriority  Subpriority value (starting from 0).
+ */
+__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL);
+  *pSubPriority     = (Priority                   ) & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL);
+}
+
+
+
+/**
+  \brief   Set Interrupt Vector
+  \details Sets an interrupt vector in SRAM based interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+           Address 0 must be mapped to SRAM.
+  \param [in]   IRQn      Interrupt number
+  \param [in]   vector    Address of interrupt handler function
+ */
+__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector;
+}
+
+
+/**
+  \brief   Get Interrupt Vector
+  \details Reads an interrupt vector from interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn      Interrupt number.
+  \return                 Address of interrupt handler function
+ */
+__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET];
+}
+
+
+/**
+  \brief   System Reset
+  \details Initiates a system reset request to reset the MCU.
+ */
+__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void)
+{
+  __DSB();                                                          /* Ensure all outstanding memory accesses included
+                                                                       buffered write are completed before reset */
+  SCB->AIRCR  = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) |
+                 SCB_AIRCR_SYSRESETREQ_Msk);
+  __DSB();                                                          /* Ensure completion of memory access */
+
+  for(;;)                                                           /* wait until reset */
+  {
+    __NOP();
+  }
+}
+
+/*@} end of CMSIS_Core_NVICFunctions */
+
+
+/* ##########################  FPU functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_FpuFunctions FPU Functions
+  \brief    Function that provides FPU type.
+  @{
+ */
+
+/**
+  \brief   get FPU type
+  \details returns the FPU type
+  \returns
+   - \b  0: No FPU
+   - \b  1: Single precision FPU
+   - \b  2: Double + Single precision FPU
+ */
+__STATIC_INLINE uint32_t SCB_GetFPUType(void)
+{
+    return 0U;           /* No FPU */
+}
+
+
+/*@} end of CMSIS_Core_FpuFunctions */
+
+
+
+/* ##################################    SysTick function  ############################################ */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_SysTickFunctions SysTick Functions
+  \brief    Functions that configure the System.
+  @{
+ */
+
+#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U)
+
+/**
+  \brief   System Tick Configuration
+  \details Initializes the System Timer and its interrupt, and starts the System Tick Timer.
+           Counter is in free running mode to generate periodic interrupts.
+  \param [in]  ticks  Number of ticks between two interrupts.
+  \return          0  Function succeeded.
+  \return          1  Function failed.
+  \note    When the variable <b>__Vendor_SysTickConfig</b> is set to 1, then the
+           function <b>SysTick_Config</b> is not included. In this case, the file <b><i>device</i>.h</b>
+           must contain a vendor-specific implementation of this function.
+ */
+__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks)
+{
+  if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk)
+  {
+    return (1UL);                                                   /* Reload value impossible */
+  }
+
+  SysTick->LOAD  = (uint32_t)(ticks - 1UL);                         /* set reload register */
+  NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */
+  SysTick->VAL   = 0UL;                                             /* Load the SysTick Counter Value */
+  SysTick->CTRL  = SysTick_CTRL_CLKSOURCE_Msk |
+                   SysTick_CTRL_TICKINT_Msk   |
+                   SysTick_CTRL_ENABLE_Msk;                         /* Enable SysTick IRQ and SysTick Timer */
+  return (0UL);                                                     /* Function successful */
+}
+
+#endif
+
+/*@} end of CMSIS_Core_SysTickFunctions */
+
+
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM1_H_DEPENDANT */
+
+#endif /* __CMSIS_GENERIC */

fw_hal/Drivers/CMSIS/Include/mpu_armv7.h

@@ -0,0 +1,270 @@
+/******************************************************************************
+ * @file     mpu_armv7.h
+ * @brief    CMSIS MPU API for Armv7-M MPU
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+ 
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header    /* treat file as system include file */
+#endif
+ 
+#ifndef ARM_MPU_ARMV7_H
+#define ARM_MPU_ARMV7_H
+
+#define ARM_MPU_REGION_SIZE_32B      ((uint8_t)0x04U) ///!< MPU Region Size 32 Bytes
+#define ARM_MPU_REGION_SIZE_64B      ((uint8_t)0x05U) ///!< MPU Region Size 64 Bytes
+#define ARM_MPU_REGION_SIZE_128B     ((uint8_t)0x06U) ///!< MPU Region Size 128 Bytes
+#define ARM_MPU_REGION_SIZE_256B     ((uint8_t)0x07U) ///!< MPU Region Size 256 Bytes
+#define ARM_MPU_REGION_SIZE_512B     ((uint8_t)0x08U) ///!< MPU Region Size 512 Bytes
+#define ARM_MPU_REGION_SIZE_1KB      ((uint8_t)0x09U) ///!< MPU Region Size 1 KByte
+#define ARM_MPU_REGION_SIZE_2KB      ((uint8_t)0x0AU) ///!< MPU Region Size 2 KBytes
+#define ARM_MPU_REGION_SIZE_4KB      ((uint8_t)0x0BU) ///!< MPU Region Size 4 KBytes
+#define ARM_MPU_REGION_SIZE_8KB      ((uint8_t)0x0CU) ///!< MPU Region Size 8 KBytes
+#define ARM_MPU_REGION_SIZE_16KB     ((uint8_t)0x0DU) ///!< MPU Region Size 16 KBytes
+#define ARM_MPU_REGION_SIZE_32KB     ((uint8_t)0x0EU) ///!< MPU Region Size 32 KBytes
+#define ARM_MPU_REGION_SIZE_64KB     ((uint8_t)0x0FU) ///!< MPU Region Size 64 KBytes
+#define ARM_MPU_REGION_SIZE_128KB    ((uint8_t)0x10U) ///!< MPU Region Size 128 KBytes
+#define ARM_MPU_REGION_SIZE_256KB    ((uint8_t)0x11U) ///!< MPU Region Size 256 KBytes
+#define ARM_MPU_REGION_SIZE_512KB    ((uint8_t)0x12U) ///!< MPU Region Size 512 KBytes
+#define ARM_MPU_REGION_SIZE_1MB      ((uint8_t)0x13U) ///!< MPU Region Size 1 MByte
+#define ARM_MPU_REGION_SIZE_2MB      ((uint8_t)0x14U) ///!< MPU Region Size 2 MBytes
+#define ARM_MPU_REGION_SIZE_4MB      ((uint8_t)0x15U) ///!< MPU Region Size 4 MBytes
+#define ARM_MPU_REGION_SIZE_8MB      ((uint8_t)0x16U) ///!< MPU Region Size 8 MBytes
+#define ARM_MPU_REGION_SIZE_16MB     ((uint8_t)0x17U) ///!< MPU Region Size 16 MBytes
+#define ARM_MPU_REGION_SIZE_32MB     ((uint8_t)0x18U) ///!< MPU Region Size 32 MBytes
+#define ARM_MPU_REGION_SIZE_64MB     ((uint8_t)0x19U) ///!< MPU Region Size 64 MBytes
+#define ARM_MPU_REGION_SIZE_128MB    ((uint8_t)0x1AU) ///!< MPU Region Size 128 MBytes
+#define ARM_MPU_REGION_SIZE_256MB    ((uint8_t)0x1BU) ///!< MPU Region Size 256 MBytes
+#define ARM_MPU_REGION_SIZE_512MB    ((uint8_t)0x1CU) ///!< MPU Region Size 512 MBytes
+#define ARM_MPU_REGION_SIZE_1GB      ((uint8_t)0x1DU) ///!< MPU Region Size 1 GByte
+#define ARM_MPU_REGION_SIZE_2GB      ((uint8_t)0x1EU) ///!< MPU Region Size 2 GBytes
+#define ARM_MPU_REGION_SIZE_4GB      ((uint8_t)0x1FU) ///!< MPU Region Size 4 GBytes
+
+#define ARM_MPU_AP_NONE 0U ///!< MPU Access Permission no access
+#define ARM_MPU_AP_PRIV 1U ///!< MPU Access Permission privileged access only
+#define ARM_MPU_AP_URO  2U ///!< MPU Access Permission unprivileged access read-only
+#define ARM_MPU_AP_FULL 3U ///!< MPU Access Permission full access
+#define ARM_MPU_AP_PRO  5U ///!< MPU Access Permission privileged access read-only
+#define ARM_MPU_AP_RO   6U ///!< MPU Access Permission read-only access
+
+/** MPU Region Base Address Register Value
+*
+* \param Region The region to be configured, number 0 to 15.
+* \param BaseAddress The base address for the region.
+*/
+#define ARM_MPU_RBAR(Region, BaseAddress) \
+  (((BaseAddress) & MPU_RBAR_ADDR_Msk) |  \
+   ((Region) & MPU_RBAR_REGION_Msk)    |  \
+   (MPU_RBAR_VALID_Msk))
+
+/**
+* MPU Memory Access Attributes
+* 
+* \param TypeExtField      Type extension field, allows you to configure memory access type, for example strongly ordered, peripheral.
+* \param IsShareable       Region is shareable between multiple bus masters.
+* \param IsCacheable       Region is cacheable, i.e. its value may be kept in cache.
+* \param IsBufferable      Region is bufferable, i.e. using write-back caching. Cacheable but non-bufferable regions use write-through policy.
+*/  
+#define ARM_MPU_ACCESS_(TypeExtField, IsShareable, IsCacheable, IsBufferable)   \
+  ((((TypeExtField ) << MPU_RASR_TEX_Pos) & MPU_RASR_TEX_Msk)                 | \
+   (((IsShareable ) << MPU_RASR_S_Pos) & MPU_RASR_S_Msk)                      | \
+   (((IsCacheable ) << MPU_RASR_C_Pos) & MPU_RASR_C_Msk)                      | \
+   (((IsBufferable ) << MPU_RASR_B_Pos) & MPU_RASR_B_Msk))
+
+/**
+* MPU Region Attribute and Size Register Value
+* 
+* \param DisableExec       Instruction access disable bit, 1= disable instruction fetches.
+* \param AccessPermission  Data access permissions, allows you to configure read/write access for User and Privileged mode.
+* \param AccessAttributes  Memory access attribution, see \ref ARM_MPU_ACCESS_.
+* \param SubRegionDisable  Sub-region disable field.
+* \param Size              Region size of the region to be configured, for example 4K, 8K.
+*/
+#define ARM_MPU_RASR_EX(DisableExec, AccessPermission, AccessAttributes, SubRegionDisable, Size)      \
+  ((((DisableExec ) << MPU_RASR_XN_Pos) & MPU_RASR_XN_Msk)                                          | \
+   (((AccessPermission) << MPU_RASR_AP_Pos) & MPU_RASR_AP_Msk)                                      | \
+   (((AccessAttributes) ) & (MPU_RASR_TEX_Msk | MPU_RASR_S_Msk | MPU_RASR_C_Msk | MPU_RASR_B_Msk)))
+  
+/**
+* MPU Region Attribute and Size Register Value
+* 
+* \param DisableExec       Instruction access disable bit, 1= disable instruction fetches.
+* \param AccessPermission  Data access permissions, allows you to configure read/write access for User and Privileged mode.
+* \param TypeExtField      Type extension field, allows you to configure memory access type, for example strongly ordered, peripheral.
+* \param IsShareable       Region is shareable between multiple bus masters.
+* \param IsCacheable       Region is cacheable, i.e. its value may be kept in cache.
+* \param IsBufferable      Region is bufferable, i.e. using write-back caching. Cacheable but non-bufferable regions use write-through policy.
+* \param SubRegionDisable  Sub-region disable field.
+* \param Size              Region size of the region to be configured, for example 4K, 8K.
+*/                         
+#define ARM_MPU_RASR(DisableExec, AccessPermission, TypeExtField, IsShareable, IsCacheable, IsBufferable, SubRegionDisable, Size) \
+  ARM_MPU_RASR_EX(DisableExec, AccessPermission, ARM_MPU_ACCESS_(TypeExtField, IsShareable, IsCacheable, IsBufferable), SubRegionDisable, Size)
+
+/**
+* MPU Memory Access Attribute for strongly ordered memory.
+*  - TEX: 000b
+*  - Shareable
+*  - Non-cacheable
+*  - Non-bufferable
+*/ 
+#define ARM_MPU_ACCESS_ORDERED ARM_MPU_ACCESS_(0U, 1U, 0U, 0U)
+
+/**
+* MPU Memory Access Attribute for device memory.
+*  - TEX: 000b (if non-shareable) or 010b (if shareable)
+*  - Shareable or non-shareable
+*  - Non-cacheable
+*  - Bufferable (if shareable) or non-bufferable (if non-shareable)
+*
+* \param IsShareable Configures the device memory as shareable or non-shareable.
+*/ 
+#define ARM_MPU_ACCESS_DEVICE(IsShareable) ((IsShareable) ? ARM_MPU_ACCESS_(0U, 1U, 0U, 1U) : ARM_MPU_ACCESS_(2U, 0U, 0U, 0U))
+
+/**
+* MPU Memory Access Attribute for normal memory.
+*  - TEX: 1BBb (reflecting outer cacheability rules)
+*  - Shareable or non-shareable
+*  - Cacheable or non-cacheable (reflecting inner cacheability rules)
+*  - Bufferable or non-bufferable (reflecting inner cacheability rules)
+*
+* \param OuterCp Configures the outer cache policy.
+* \param InnerCp Configures the inner cache policy.
+* \param IsShareable Configures the memory as shareable or non-shareable.
+*/ 
+#define ARM_MPU_ACCESS_NORMAL(OuterCp, InnerCp, IsShareable) ARM_MPU_ACCESS_((4U | (OuterCp)), IsShareable, ((InnerCp) & 2U), ((InnerCp) & 1U))
+
+/**
+* MPU Memory Access Attribute non-cacheable policy.
+*/
+#define ARM_MPU_CACHEP_NOCACHE 0U
+
+/**
+* MPU Memory Access Attribute write-back, write and read allocate policy.
+*/
+#define ARM_MPU_CACHEP_WB_WRA 1U
+
+/**
+* MPU Memory Access Attribute write-through, no write allocate policy.
+*/
+#define ARM_MPU_CACHEP_WT_NWA 2U
+
+/**
+* MPU Memory Access Attribute write-back, no write allocate policy.
+*/
+#define ARM_MPU_CACHEP_WB_NWA 3U
+
+
+/**
+* Struct for a single MPU Region
+*/
+typedef struct {
+  uint32_t RBAR; //!< The region base address register value (RBAR)
+  uint32_t RASR; //!< The region attribute and size register value (RASR) \ref MPU_RASR
+} ARM_MPU_Region_t;
+    
+/** Enable the MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+
+/** Clear and disable the given MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion(uint32_t rnr)
+{
+  MPU->RNR = rnr;
+  MPU->RASR = 0U;
+}
+
+/** Configure an MPU region.
+* \param rbar Value for RBAR register.
+* \param rsar Value for RSAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion(uint32_t rbar, uint32_t rasr)
+{
+  MPU->RBAR = rbar;
+  MPU->RASR = rasr;
+}
+
+/** Configure the given MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rsar Value for RSAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegionEx(uint32_t rnr, uint32_t rbar, uint32_t rasr)
+{
+  MPU->RNR = rnr;
+  MPU->RBAR = rbar;
+  MPU->RASR = rasr;
+}
+
+/** Memcopy with strictly ordered memory access, e.g. for register targets.
+* \param dst Destination data is copied to.
+* \param src Source data is copied from.
+* \param len Amount of data words to be copied.
+*/
+__STATIC_INLINE void orderedCpy(volatile uint32_t* dst, const uint32_t* __RESTRICT src, uint32_t len)
+{
+  uint32_t i;
+  for (i = 0U; i < len; ++i) 
+  {
+    dst[i] = src[i];
+  }
+}
+
+/** Load the given number of MPU regions from a table.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load(ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  const uint32_t rowWordSize = sizeof(ARM_MPU_Region_t)/4U;
+  while (cnt > MPU_TYPE_RALIASES) {
+    orderedCpy(&(MPU->RBAR), &(table->RBAR), MPU_TYPE_RALIASES*rowWordSize);
+    table += MPU_TYPE_RALIASES;
+    cnt -= MPU_TYPE_RALIASES;
+  }
+  orderedCpy(&(MPU->RBAR), &(table->RBAR), cnt*rowWordSize);
+}
+
+#endif

fw_hal/Drivers/CMSIS/Include/mpu_armv8.h

@@ -0,0 +1,333 @@
+/******************************************************************************
+ * @file     mpu_armv8.h
+ * @brief    CMSIS MPU API for Armv8-M MPU
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header    /* treat file as system include file */
+#endif
+
+#ifndef ARM_MPU_ARMV8_H
+#define ARM_MPU_ARMV8_H
+
+/** \brief Attribute for device memory (outer only) */
+#define ARM_MPU_ATTR_DEVICE                           ( 0U )
+
+/** \brief Attribute for non-cacheable, normal memory */
+#define ARM_MPU_ATTR_NON_CACHEABLE                    ( 4U )
+
+/** \brief Attribute for normal memory (outer and inner)
+* \param NT Non-Transient: Set to 1 for non-transient data.
+* \param WB Write-Back: Set to 1 to use write-back update policy.
+* \param RA Read Allocation: Set to 1 to use cache allocation on read miss.
+* \param WA Write Allocation: Set to 1 to use cache allocation on write miss.
+*/
+#define ARM_MPU_ATTR_MEMORY_(NT, WB, RA, WA) \
+  (((NT & 1U) << 3U) | ((WB & 1U) << 2U) | ((RA & 1U) << 1U) | (WA & 1U))
+
+/** \brief Device memory type non Gathering, non Re-ordering, non Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGnRnE (0U)
+
+/** \brief Device memory type non Gathering, non Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGnRE  (1U)
+
+/** \brief Device memory type non Gathering, Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGRE   (2U)
+
+/** \brief Device memory type Gathering, Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_GRE    (3U)
+
+/** \brief Memory Attribute
+* \param O Outer memory attributes
+* \param I O == ARM_MPU_ATTR_DEVICE: Device memory attributes, else: Inner memory attributes
+*/
+#define ARM_MPU_ATTR(O, I) (((O & 0xFU) << 4U) | (((O & 0xFU) != 0U) ? (I & 0xFU) : ((I & 0x3U) << 2U)))
+
+/** \brief Normal memory non-shareable  */
+#define ARM_MPU_SH_NON   (0U)
+
+/** \brief Normal memory outer shareable  */
+#define ARM_MPU_SH_OUTER (2U)
+
+/** \brief Normal memory inner shareable  */
+#define ARM_MPU_SH_INNER (3U)
+
+/** \brief Memory access permissions
+* \param RO Read-Only: Set to 1 for read-only memory.
+* \param NP Non-Privileged: Set to 1 for non-privileged memory.
+*/
+#define ARM_MPU_AP_(RO, NP) (((RO & 1U) << 1U) | (NP & 1U))
+
+/** \brief Region Base Address Register value
+* \param BASE The base address bits [31:5] of a memory region. The value is zero extended. Effective address gets 32 byte aligned.
+* \param SH Defines the Shareability domain for this memory region.
+* \param RO Read-Only: Set to 1 for a read-only memory region.
+* \param NP Non-Privileged: Set to 1 for a non-privileged memory region.
+* \oaram XN eXecute Never: Set to 1 for a non-executable memory region.
+*/
+#define ARM_MPU_RBAR(BASE, SH, RO, NP, XN) \
+  ((BASE & MPU_RBAR_BASE_Msk) | \
+  ((SH << MPU_RBAR_SH_Pos) & MPU_RBAR_SH_Msk) | \
+  ((ARM_MPU_AP_(RO, NP) << MPU_RBAR_AP_Pos) & MPU_RBAR_AP_Msk) | \
+  ((XN << MPU_RBAR_XN_Pos) & MPU_RBAR_XN_Msk))
+
+/** \brief Region Limit Address Register value
+* \param LIMIT The limit address bits [31:5] for this memory region. The value is one extended.
+* \param IDX The attribute index to be associated with this memory region.
+*/
+#define ARM_MPU_RLAR(LIMIT, IDX) \
+  ((LIMIT & MPU_RLAR_LIMIT_Msk) | \
+  ((IDX << MPU_RLAR_AttrIndx_Pos) & MPU_RLAR_AttrIndx_Msk) | \
+  (MPU_RLAR_EN_Msk))
+
+/**
+* Struct for a single MPU Region
+*/
+typedef struct {
+  uint32_t RBAR;                   /*!< Region Base Address Register value */
+  uint32_t RLAR;                   /*!< Region Limit Address Register value */
+} ARM_MPU_Region_t;
+    
+/** Enable the MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+
+#ifdef MPU_NS
+/** Enable the Non-secure MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable_NS(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU_NS->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB_NS->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the Non-secure MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable_NS(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB_NS->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU_NS->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+#endif
+
+/** Set the memory attribute encoding to the given MPU.
+* \param mpu Pointer to the MPU to be configured.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttrEx(MPU_Type* mpu, uint8_t idx, uint8_t attr)
+{
+  const uint8_t reg = idx / 4U;
+  const uint32_t pos = ((idx % 4U) * 8U);
+  const uint32_t mask = 0xFFU << pos;
+  
+  if (reg >= (sizeof(mpu->MAIR) / sizeof(mpu->MAIR[0]))) {
+    return; // invalid index
+  }
+  
+  mpu->MAIR[reg] = ((mpu->MAIR[reg] & ~mask) | ((attr << pos) & mask));
+}
+
+/** Set the memory attribute encoding.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttr(uint8_t idx, uint8_t attr)
+{
+  ARM_MPU_SetMemAttrEx(MPU, idx, attr);
+}
+
+#ifdef MPU_NS
+/** Set the memory attribute encoding to the Non-secure MPU.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttr_NS(uint8_t idx, uint8_t attr)
+{
+  ARM_MPU_SetMemAttrEx(MPU_NS, idx, attr);
+}
+#endif
+
+/** Clear and disable the given MPU region of the given MPU.
+* \param mpu Pointer to MPU to be used.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegionEx(MPU_Type* mpu, uint32_t rnr)
+{
+  mpu->RNR = rnr;
+  mpu->RLAR = 0U;
+}
+
+/** Clear and disable the given MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion(uint32_t rnr)
+{
+  ARM_MPU_ClrRegionEx(MPU, rnr);
+}
+
+#ifdef MPU_NS
+/** Clear and disable the given Non-secure MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion_NS(uint32_t rnr)
+{  
+  ARM_MPU_ClrRegionEx(MPU_NS, rnr);
+}
+#endif
+
+/** Configure the given MPU region of the given MPU.
+* \param mpu Pointer to MPU to be used.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegionEx(MPU_Type* mpu, uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  mpu->RNR = rnr;
+  mpu->RBAR = rbar;
+  mpu->RLAR = rlar;
+}
+
+/** Configure the given MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion(uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  ARM_MPU_SetRegionEx(MPU, rnr, rbar, rlar);
+}
+
+#ifdef MPU_NS
+/** Configure the given Non-secure MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion_NS(uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  ARM_MPU_SetRegionEx(MPU_NS, rnr, rbar, rlar);  
+}
+#endif
+
+/** Memcopy with strictly ordered memory access, e.g. for register targets.
+* \param dst Destination data is copied to.
+* \param src Source data is copied from.
+* \param len Amount of data words to be copied.
+*/
+__STATIC_INLINE void orderedCpy(volatile uint32_t* dst, const uint32_t* __RESTRICT src, uint32_t len)
+{
+  uint32_t i;
+  for (i = 0U; i < len; ++i) 
+  {
+    dst[i] = src[i];
+  }
+}
+
+/** Load the given number of MPU regions from a table to the given MPU.
+* \param mpu Pointer to the MPU registers to be used.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_LoadEx(MPU_Type* mpu, uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  const uint32_t rowWordSize = sizeof(ARM_MPU_Region_t)/4U;
+  if (cnt == 1U) {
+    mpu->RNR = rnr;
+    orderedCpy(&(mpu->RBAR), &(table->RBAR), rowWordSize);
+  } else {
+    uint32_t rnrBase   = rnr & ~(MPU_TYPE_RALIASES-1U);
+    uint32_t rnrOffset = rnr % MPU_TYPE_RALIASES;
+    
+    mpu->RNR = rnrBase;
+    while ((rnrOffset + cnt) > MPU_TYPE_RALIASES) {
+      uint32_t c = MPU_TYPE_RALIASES - rnrOffset;
+      orderedCpy(&(mpu->RBAR)+(rnrOffset*2U), &(table->RBAR), c*rowWordSize);
+      table += c;
+      cnt -= c;
+      rnrOffset = 0U;
+      rnrBase += MPU_TYPE_RALIASES;
+      mpu->RNR = rnrBase;
+    }
+    
+    orderedCpy(&(mpu->RBAR)+(rnrOffset*2U), &(table->RBAR), cnt*rowWordSize);
+  }
+}
+
+/** Load the given number of MPU regions from a table.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load(uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  ARM_MPU_LoadEx(MPU, rnr, table, cnt);
+}
+
+#ifdef MPU_NS
+/** Load the given number of MPU regions from a table to the Non-secure MPU.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load_NS(uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  ARM_MPU_LoadEx(MPU_NS, rnr, table, cnt);
+}
+#endif
+
+#endif
+

fw_hal/Drivers/CMSIS/Include/tz_context.h

@@ -0,0 +1,70 @@
+/******************************************************************************
+ * @file     tz_context.h
+ * @brief    Context Management for Armv8-M TrustZone
+ * @version  V1.0.1
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef TZ_CONTEXT_H
+#define TZ_CONTEXT_H
+ 
+#include <stdint.h>
+ 
+#ifndef TZ_MODULEID_T
+#define TZ_MODULEID_T
+/// \details Data type that identifies secure software modules called by a process.
+typedef uint32_t TZ_ModuleId_t;
+#endif
+ 
+/// \details TZ Memory ID identifies an allocated memory slot.
+typedef uint32_t TZ_MemoryId_t;
+  
+/// Initialize secure context memory system
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_InitContextSystem_S (void);
+ 
+/// Allocate context memory for calling secure software modules in TrustZone
+/// \param[in]  module   identifies software modules called from non-secure mode
+/// \return value != 0 id TrustZone memory slot identifier
+/// \return value 0    no memory available or internal error
+TZ_MemoryId_t TZ_AllocModuleContext_S (TZ_ModuleId_t module);
+ 
+/// Free context memory that was previously allocated with \ref TZ_AllocModuleContext_S
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_FreeModuleContext_S (TZ_MemoryId_t id);
+ 
+/// Load secure context (called on RTOS thread context switch)
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_LoadContext_S (TZ_MemoryId_t id);
+ 
+/// Store secure context (called on RTOS thread context switch)
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_StoreContext_S (TZ_MemoryId_t id);
+ 
+#endif  // TZ_CONTEXT_H

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal.h

@@ -0,0 +1,487 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal.h
+  * @author  MCD Application Team
+  * @brief   This file contains all the functions prototypes for the HAL
+  *          module driver.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_H
+#define __STM32L0xx_HAL_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_conf.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup HAL HAL
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup HAL_Exported_Constants HAL Exported Constants
+  * @{
+  */
+
+/** @defgroup HAL_TICK_FREQ Tick Frequency
+  * @{
+  */
+typedef enum
+{
+  HAL_TICK_FREQ_10HZ         = 100U,
+  HAL_TICK_FREQ_100HZ        = 10U,
+  HAL_TICK_FREQ_1KHZ         = 1U,
+  HAL_TICK_FREQ_DEFAULT      = HAL_TICK_FREQ_1KHZ
+} HAL_TickFreqTypeDef;
+/**
+  * @}
+  */
+
+/** @defgroup SYSCFG_BootMode Boot Mode
+  * @{
+  */
+#define SYSCFG_BOOT_MAINFLASH          (0x00000000U)
+#define SYSCFG_BOOT_SYSTEMFLASH        SYSCFG_CFGR1_BOOT_MODE_0
+#define SYSCFG_BOOT_SRAM               SYSCFG_CFGR1_BOOT_MODE
+
+/**
+  * @}
+  */
+
+/** @defgroup DBGMCU_Low_Power_Config DBGMCU Low Power Configuration
+  * @{
+  */
+#define DBGMCU_SLEEP                 DBGMCU_CR_DBG_SLEEP
+#define DBGMCU_STOP                  DBGMCU_CR_DBG_STOP
+#define DBGMCU_STANDBY               DBGMCU_CR_DBG_STANDBY
+#define IS_DBGMCU_PERIPH(__PERIPH__) ((((__PERIPH__) & (~(DBGMCU_CR_DBG))) == 0x00U) && ((__PERIPH__) != 0x00U))
+
+
+/**
+  * @}
+  */
+
+#if defined (LCD_BASE) /* STM32L0x3xx only */
+/** @defgroup SYSCFG_LCD_EXT_CAPA SYSCFG LCD External Capacitors
+  * @{
+  */
+#define SYSCFG_LCD_EXT_CAPA             SYSCFG_CFGR2_CAPA /*!< Connection of internal Vlcd rail to external capacitors */
+#define SYSCFG_VLCD_PB2_EXT_CAPA_ON     SYSCFG_CFGR2_CAPA_0  /*!< Connection on PB2   */
+#define SYSCFG_VLCD_PB12_EXT_CAPA_ON    SYSCFG_CFGR2_CAPA_1  /*!< Connection on PB12  */
+#define SYSCFG_VLCD_PB0_EXT_CAPA_ON     SYSCFG_CFGR2_CAPA_2  /*!< Connection on PB0   */
+#if defined (SYSCFG_CFGR2_CAPA_3)
+#define SYSCFG_VLCD_PE11_EXT_CAPA_ON    SYSCFG_CFGR2_CAPA_3  /*!< Connection on PE11  */
+#endif
+#if defined (SYSCFG_CFGR2_CAPA_4)
+#define SYSCFG_VLCD_PE12_EXT_CAPA_ON    SYSCFG_CFGR2_CAPA_4  /*!< Connection on PE12  */
+#endif
+
+/**
+  * @}
+  */
+#endif
+
+/** @defgroup SYSCFG_VREFINT_OUT_SELECT SYSCFG VREFINT Out Selection
+  * @{
+  */
+#define SYSCFG_VREFINT_OUT_NONE          (0x00000000U)           /* no pad connected */
+#define SYSCFG_VREFINT_OUT_PB0           SYSCFG_CFGR3_VREF_OUT_0 /* Selects PBO as output for the Vrefint */
+#define SYSCFG_VREFINT_OUT_PB1           SYSCFG_CFGR3_VREF_OUT_1 /* Selects PB1 as output for the Vrefint */
+#define SYSCFG_VREFINT_OUT_PB0_PB1       SYSCFG_CFGR3_VREF_OUT   /* Selects PBO and PB1 as output for the Vrefint */
+
+#define IS_SYSCFG_VREFINT_OUT_SELECT(OUTPUT)   (((OUTPUT) == SYSCFG_VREFINT_OUT_NONE)  || \
+                                                ((OUTPUT) == SYSCFG_VREFINT_OUT_PB0)  || \
+                                                ((OUTPUT) == SYSCFG_VREFINT_OUT_PB1)  || \
+                                                ((OUTPUT) == SYSCFG_VREFINT_OUT_PB0_PB1))
+/**
+  * @}
+  */
+
+/** @defgroup SYSCFG_flags_definition SYSCFG Flags Definition
+  * @{
+  */
+#define SYSCFG_FLAG_VREFINT_READY      SYSCFG_CFGR3_VREFINT_RDYF
+
+#define IS_SYSCFG_FLAG(FLAG)           ((FLAG) == SYSCFG_FLAG_VREFINT_READY))
+
+/**
+  * @}
+  */
+
+/** @defgroup SYSCFG_FastModePlus_GPIO Fast Mode Plus on GPIO
+  * @{
+  */
+/** @brief  Fast mode Plus driving capability on a specific GPIO
+  */
+#if defined (SYSCFG_CFGR2_I2C_PB6_FMP)
+#define SYSCFG_FASTMODEPLUS_PB6       SYSCFG_CFGR2_I2C_PB6_FMP  /* Enable Fast Mode Plus on PB6 */
+#endif
+#if defined (SYSCFG_CFGR2_I2C_PB7_FMP)
+#define SYSCFG_FASTMODEPLUS_PB7       SYSCFG_CFGR2_I2C_PB7_FMP  /* Enable Fast Mode Plus on PB7 */
+#endif
+#if defined (SYSCFG_CFGR2_I2C_PB8_FMP)
+#define SYSCFG_FASTMODEPLUS_PB8       SYSCFG_CFGR2_I2C_PB8_FMP  /* Enable Fast Mode Plus on PB8 */
+#endif
+#if defined (SYSCFG_CFGR2_I2C_PB9_FMP)
+#define SYSCFG_FASTMODEPLUS_PB9       SYSCFG_CFGR2_I2C_PB9_FMP  /* Enable Fast Mode Plus on PB9 */
+#endif
+
+#define IS_SYSCFG_FASTMODEPLUS(PIN) ((((PIN) & (SYSCFG_FASTMODEPLUS_PB6)) == SYSCFG_FASTMODEPLUS_PB6)  || \
+                                     (((PIN) & (SYSCFG_FASTMODEPLUS_PB7)) == SYSCFG_FASTMODEPLUS_PB7)  || \
+                                     (((PIN) & (SYSCFG_FASTMODEPLUS_PB8)) == SYSCFG_FASTMODEPLUS_PB8)  || \
+                                     (((PIN) & (SYSCFG_FASTMODEPLUS_PB9)) == SYSCFG_FASTMODEPLUS_PB9)  )
+/**
+ * @}
+ */
+ /**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup HAL_Exported_Macros HAL Exported Macros
+  * @{
+  */
+
+/** @brief  Freeze/Unfreeze Peripherals in Debug mode
+  */
+#if defined (DBGMCU_APB1_FZ_DBG_TIM2_STOP)
+/**
+  * @brief  TIM2 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM2()     SET_BIT(DBGMCU->APB1FZ,DBGMCU_APB1_FZ_DBG_TIM2_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM2()   CLEAR_BIT(DBGMCU->APB1FZ,DBGMCU_APB1_FZ_DBG_TIM2_STOP)
+#endif
+
+#if defined (DBGMCU_APB1_FZ_DBG_TIM3_STOP)
+/**
+  * @brief  TIM3 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM3()     SET_BIT(DBGMCU->APB1FZ,DBGMCU_APB1_FZ_DBG_TIM3_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM3()   CLEAR_BIT(DBGMCU->APB1FZ,DBGMCU_APB1_FZ_DBG_TIM3_STOP)
+#endif
+
+#if defined (DBGMCU_APB1_FZ_DBG_TIM6_STOP)
+/**
+  * @brief  TIM6 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM6()     SET_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_TIM6_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM6()   CLEAR_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_TIM6_STOP)
+#endif
+
+#if defined (DBGMCU_APB1_FZ_DBG_TIM7_STOP)
+/**
+  * @brief  TIM7 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM7()     SET_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_TIM7_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM7()   CLEAR_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_TIM7_STOP)
+#endif
+
+#if defined (DBGMCU_APB1_FZ_DBG_RTC_STOP)
+/**
+  * @brief  RTC Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_RTC()      SET_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_RTC_STOP)
+#define __HAL_DBGMCU_UNFREEZE_RTC()    CLEAR_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_RTC_STOP)
+#endif
+
+#if defined (DBGMCU_APB1_FZ_DBG_WWDG_STOP)
+/**
+  * @brief  WWDG Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_WWDG()     SET_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_WWDG_STOP)
+#define __HAL_DBGMCU_UNFREEZE_WWDG()   CLEAR_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_WWDG_STOP)
+#endif
+
+#if defined (DBGMCU_APB1_FZ_DBG_IWDG_STOP)
+/**
+  * @brief  IWDG Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_IWDG()     SET_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_IWDG_STOP)
+#define __HAL_DBGMCU_UNFREEZE_IWDG()   CLEAR_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_IWDG_STOP)
+#endif
+
+#if defined (DBGMCU_APB1_FZ_DBG_I2C1_STOP)
+/**
+  * @brief  I2C1 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_I2C1_TIMEOUT()   SET_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_I2C1_STOP)
+#define __HAL_DBGMCU_UNFREEZE_I2C1_TIMEOUT_DBGMCU() CLEAR_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_I2C1_STOP)
+#endif
+
+#if defined (DBGMCU_APB1_FZ_DBG_I2C2_STOP)
+/**
+  * @brief  I2C2 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_I2C2_TIMEOUT_DBGMCU()   SET_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_I2C2_STOP)
+#define __HAL_DBGMCU_UNFREEZE_I2C2_TIMEOUT_DBGMCU() CLEAR_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_I2C2_STOP)
+#endif
+
+#if defined (DBGMCU_APB1_FZ_DBG_I2C3_STOP)
+/**
+  * @brief  I2C3 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_I2C3_TIMEOUT()   SET_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_I2C3_STOP)
+#define __HAL_DBGMCU_UNFREEZE_I2C3_TIMEOUT() CLEAR_BIT(DBGMCU->APB1FZ, DBGMCU_APB1_FZ_DBG_I2C3_STOP)
+#endif
+
+#if defined (DBGMCU_APB1_FZ_DBG_LPTIMER_STOP)
+/**
+  * @brief  LPTIMER Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_LPTIMER()        SET_BIT(DBGMCU->APB1FZ ,DBGMCU_APB1_FZ_DBG_LPTIMER_STOP)
+#define __HAL_DBGMCU_UNFREEZE_LPTIMER()      CLEAR_BIT(DBGMCU->APB1FZ ,DBGMCU_APB1_FZ_DBG_LPTIMER_STOP)
+#endif
+
+#if defined (DBGMCU_APB2_FZ_DBG_TIM22_STOP)
+/**
+  * @brief  TIM22 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM22()          SET_BIT(DBGMCU->APB2FZ, DBGMCU_APB2_FZ_DBG_TIM22_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM22()        CLEAR_BIT(DBGMCU->APB2FZ, DBGMCU_APB2_FZ_DBG_TIM22_STOP)
+#endif
+
+#if defined (DBGMCU_APB2_FZ_DBG_TIM21_STOP)
+/**
+  * @brief  TIM21 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM21()          SET_BIT(DBGMCU->APB2FZ, DBGMCU_APB2_FZ_DBG_TIM21_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM21()        CLEAR_BIT(DBGMCU->APB2FZ, DBGMCU_APB2_FZ_DBG_TIM21_STOP)
+#endif
+
+/** @brief  Main Flash memory mapped at 0x00000000
+  */
+#define __HAL_SYSCFG_REMAPMEMORY_FLASH()     CLEAR_BIT(SYSCFG->CFGR1, SYSCFG_CFGR1_MEM_MODE)
+
+/** @brief  System Flash memory mapped at 0x00000000
+  */
+#define __HAL_SYSCFG_REMAPMEMORY_SYSTEMFLASH()      MODIFY_REG(SYSCFG->CFGR1, SYSCFG_CFGR1_MEM_MODE, SYSCFG_CFGR1_MEM_MODE_0)
+
+
+/** @brief  Embedded SRAM mapped at 0x00000000
+  */
+#define __HAL_SYSCFG_REMAPMEMORY_SRAM()             MODIFY_REG(SYSCFG->CFGR1, SYSCFG_CFGR1_MEM_MODE, SYSCFG_CFGR1_MEM_MODE_0 | SYSCFG_CFGR1_MEM_MODE_1)
+
+/** @brief  Configuration of the DBG Low Power mode.
+  * @param  __DBGLPMODE__ bit field to indicate in wich Low Power mode DBG is still active.
+  *         This parameter can be a value of
+  *         - DBGMCU_SLEEP
+  *         - DBGMCU_STOP
+  *         - DBGMCU_STANDBY
+  */
+#define __HAL_SYSCFG_DBG_LP_CONFIG(__DBGLPMODE__)    do {assert_param(IS_DBGMCU_PERIPH(__DBGLPMODE__)); \
+                                                       MODIFY_REG(DBGMCU->CR, DBGMCU_CR_DBG, (__DBGLPMODE__)); \
+                                                     } while (0)
+
+#if defined (LCD_BASE) /* STM32L0x3xx only */
+
+/** @brief  Macro to configure the VLCD Decoupling capacitance connection.
+  *
+  * @param  __SYSCFG_VLCD_CAPA__ specifies the decoupling of LCD capacitance for rails connection on GPIO.
+  *          This parameter can be a combination of following values (when available):
+  *            @arg SYSCFG_VLCD_PB2_EXT_CAPA_ON:  Connection on PB2
+  *            @arg SYSCFG_VLCD_PB12_EXT_CAPA_ON: Connection on PB12
+  *            @arg SYSCFG_VLCD_PB0_EXT_CAPA_ON:  Connection on PB0
+  *            @arg SYSCFG_VLCD_PE11_EXT_CAPA_ON: Connection on PE11
+  *            @arg SYSCFG_VLCD_PE12_EXT_CAPA_ON: Connection on PE12
+  * @retval None
+  */
+#define __HAL_SYSCFG_VLCD_CAPA_CONFIG(__SYSCFG_VLCD_CAPA__) \
+                  MODIFY_REG(SYSCFG->CFGR2, SYSCFG_LCD_EXT_CAPA, (uint32_t)(__SYSCFG_VLCD_CAPA__))
+
+/**
+  * @brief  Returns the decoupling of LCD capacitance configured by user.
+  * @retval The LCD capacitance connection as configured by user. The returned can be a combination of :
+  *            SYSCFG_VLCD_PB2_EXT_CAPA_ON:  Connection on PB2
+  *            SYSCFG_VLCD_PB12_EXT_CAPA_ON: Connection on PB12
+  *            SYSCFG_VLCD_PB0_EXT_CAPA_ON:  Connection on PB0
+  *            SYSCFG_VLCD_PE11_EXT_CAPA_ON: Connection on PE11
+  *            SYSCFG_VLCD_PE12_EXT_CAPA_ON: Connection on PE12
+  */
+#define __HAL_SYSCFG_GET_VLCD_CAPA_CONFIG()          READ_BIT(SYSCFG->CFGR2, SYSCFG_LCD_EXT_CAPA)
+
+#endif
+
+/**
+  * @brief  Returns the boot mode as configured by user.
+  * @retval The boot mode as configured by user. The returned can be a value of :
+  *     - SYSCFG_BOOT_MAINFLASH
+  *     - SYSCFG_BOOT_SYSTEMFLASH
+  *     - SYSCFG_BOOT_SRAM
+  */
+#define __HAL_SYSCFG_GET_BOOT_MODE()          READ_BIT(SYSCFG->CFGR1, SYSCFG_CFGR1_BOOT_MODE)
+
+
+/** @brief  Check whether the specified SYSCFG flag is set or not.
+  * @param  __FLAG__ specifies the flag to check.
+  *         The only parameter supported is SYSCFG_FLAG_VREFINT_READY
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_SYSCFG_GET_FLAG(__FLAG__) (((SYSCFG->CFGR3) & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Fast mode Plus driving capability enable macro
+  * @param __FASTMODEPLUS__ This parameter can be a value of :
+  *     @arg SYSCFG_FASTMODEPLUS_PB6
+  *     @arg SYSCFG_FASTMODEPLUS_PB7
+  *     @arg SYSCFG_FASTMODEPLUS_PB8
+  *     @arg SYSCFG_FASTMODEPLUS_PB9
+  */
+#define __HAL_SYSCFG_FASTMODEPLUS_ENABLE(__FASTMODEPLUS__)  do {assert_param(IS_SYSCFG_FASTMODEPLUS((__FASTMODEPLUS__))); \
+                                                                SET_BIT(SYSCFG->CFGR2, (__FASTMODEPLUS__));                 \
+                                                               }while(0)
+/** @brief  Fast mode Plus driving capability disable macro
+  * @param __FASTMODEPLUS__ This parameter can be a value of :
+  *     @arg SYSCFG_FASTMODEPLUS_PB6
+  *     @arg SYSCFG_FASTMODEPLUS_PB7
+  *     @arg SYSCFG_FASTMODEPLUS_PB8
+  *     @arg SYSCFG_FASTMODEPLUS_PB9
+  */
+#define __HAL_SYSCFG_FASTMODEPLUS_DISABLE(__FASTMODEPLUS__) do {assert_param(IS_SYSCFG_FASTMODEPLUS((__FASTMODEPLUS__))); \
+                                                                CLEAR_BIT(SYSCFG->CFGR2, (__FASTMODEPLUS__));               \
+                                                               }while(0)
+
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_Private_Macros HAL Private Macros
+  * @{
+  */
+#define IS_TICKFREQ(FREQ) (((FREQ) == HAL_TICK_FREQ_10HZ)  || \
+                           ((FREQ) == HAL_TICK_FREQ_100HZ) || \
+                           ((FREQ) == HAL_TICK_FREQ_1KHZ))
+/**
+  * @}
+  */
+
+/* Exported variables --------------------------------------------------------*/
+/** @defgroup HAL_Exported_Variables HAL Exported Variables
+  * @{
+  */
+extern __IO uint32_t uwTick;
+extern uint32_t uwTickPrio;
+extern HAL_TickFreqTypeDef uwTickFreq;
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup HAL_Exported_Functions HAL Exported Functions
+  * @{
+  */
+/** @defgroup HAL_Exported_Functions_Group1 Initialization and de-initialization functions
+ *  @brief    Initialization and de-initialization functions
+ * @{
+  */
+HAL_StatusTypeDef HAL_Init(void);
+HAL_StatusTypeDef HAL_DeInit(void);
+void HAL_MspInit(void);
+void HAL_MspDeInit(void);
+HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority);
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_Exported_Functions_Group2 Peripheral Control functions
+  * @brief    Peripheral Control functions
+  * @{
+  */
+void HAL_IncTick(void);
+void HAL_Delay(uint32_t Delay);
+uint32_t HAL_GetTick(void);
+uint32_t HAL_GetTickPrio(void);
+HAL_StatusTypeDef HAL_SetTickFreq(HAL_TickFreqTypeDef Freq);
+HAL_TickFreqTypeDef HAL_GetTickFreq(void);
+void HAL_SuspendTick(void);
+void HAL_ResumeTick(void);
+uint32_t HAL_GetHalVersion(void);
+uint32_t HAL_GetREVID(void);
+uint32_t HAL_GetDEVID(void);
+uint32_t HAL_GetUIDw0(void);
+uint32_t HAL_GetUIDw1(void);
+uint32_t HAL_GetUIDw2(void);
+/**
+  * @}
+  */
+
+/** @defgroup HAL_Exported_Functions_Group3 DBGMCU Peripheral Control functions
+  * @brief    DBGMCU Peripheral Control functions
+  * @{
+  */
+void HAL_DBGMCU_EnableDBGSleepMode(void);
+void HAL_DBGMCU_DisableDBGSleepMode(void);
+void HAL_DBGMCU_EnableDBGStopMode(void);
+void HAL_DBGMCU_DisableDBGStopMode(void);
+void HAL_DBGMCU_EnableDBGStandbyMode(void);
+void HAL_DBGMCU_DisableDBGStandbyMode(void);
+void HAL_DBGMCU_DBG_EnableLowPowerConfig(uint32_t Periph);
+void HAL_DBGMCU_DBG_DisableLowPowerConfig(uint32_t Periph);
+/**
+  * @}
+  */
+
+/** @defgroup HAL_Exported_Functions_Group4 SYSCFG Peripheral Control functions
+  * @brief    SYSCFG Peripheral Control functions
+  * @{
+  */
+uint32_t  HAL_SYSCFG_GetBootMode(void);
+void HAL_SYSCFG_Enable_Lock_VREFINT(void);
+void HAL_SYSCFG_Disable_Lock_VREFINT(void);
+void HAL_SYSCFG_VREFINT_OutputSelect(uint32_t SYSCFG_Vrefint_OUTPUT);
+/**
+  * @}
+  */
+/**
+  * @}
+  */
+
+/* Define the private group ***********************************/
+/**************************************************************/
+/** @defgroup HAL_Private HAL Private
+  * @{
+  */
+/**
+  * @}
+  */
+/**************************************************************/
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L0xx_HAL_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_cortex.h

@@ -0,0 +1,365 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_cortex.h
+  * @author  MCD Application Team
+  * @brief   Header file of CORTEX HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */ 
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_CORTEX_H
+#define __STM32L0xx_HAL_CORTEX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup CORTEX CORTEX
+  * @{
+  */ 
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup CORTEX_Exported_Types CORTEX Exported Types
+  * @{
+  */
+
+#if (__MPU_PRESENT == 1)
+/** @defgroup CORTEX_MPU_Region_Initialization_Structure_definition MPU Region Initialization Structure Definition
+  * @{
+  */
+typedef struct
+{
+  uint32_t               BaseAddress;           /*!< Specifies the base address of the region to protect.                           */
+
+  uint8_t                Enable;                /*!< Specifies the status of the region.
+                                                     This parameter can be a value of @ref CORTEX_MPU_Region_Enable                 */
+  uint8_t                Number;                /*!< Specifies the number of the region to protect.
+                                                     This parameter can be a value of @ref CORTEX_MPU_Region_Number                 */
+
+  uint8_t                Size;                  /*!< Specifies the size of the region to protect.
+                                                     This parameter can be a value of @ref CORTEX_MPU_Region_Size                   */
+  uint8_t                SubRegionDisable;      /*!< Specifies the number of the subregion protection to disable.
+                                                     This parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFF    */
+  uint8_t                TypeExtField;          /*!< This parameter is NOT used but is kept to keep API unified through all families*/
+
+  uint8_t                AccessPermission;      /*!< Specifies the region access permission type.
+                                                     This parameter can be a value of @ref CORTEX_MPU_Region_Permission_Attributes  */
+  uint8_t                DisableExec;           /*!< Specifies the instruction access status.
+                                                     This parameter can be a value of @ref CORTEX_MPU_Instruction_Access            */
+  uint8_t                IsShareable;           /*!< Specifies the shareability status of the protected region.
+                                                     This parameter can be a value of @ref CORTEX_MPU_Access_Shareable              */
+  uint8_t                IsCacheable;           /*!< Specifies the cacheable status of the region protected.
+                                                     This parameter can be a value of @ref CORTEX_MPU_Access_Cacheable              */
+  uint8_t                IsBufferable;          /*!< Specifies the bufferable status of the protected region.
+                                                     This parameter can be a value of @ref CORTEX_MPU_Access_Bufferable             */
+}MPU_Region_InitTypeDef;
+/**
+  * @}
+  */
+#endif /* __MPU_PRESENT */
+
+/**
+  * @}
+  */
+
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup CORTEX_Exported_Constants CORTEx Exported Constants
+  * @{
+  */
+
+
+#define IS_NVIC_PREEMPTION_PRIORITY(__PRIORITY__)  ((__PRIORITY__) < 0x10U)
+
+#define IS_NVIC_DEVICE_IRQ(IRQ)                ((IRQ) >= 0x0)
+
+/** @defgroup CORTEX_SysTick_clock_source CORTEX SysTick Clock Source
+  * @{
+  */
+#define SYSTICK_CLKSOURCE_HCLK_DIV8    (0x00000000U)
+#define SYSTICK_CLKSOURCE_HCLK         (0x00000004U)
+#define IS_SYSTICK_CLK_SOURCE(__SOURCE__) (((__SOURCE__) == SYSTICK_CLKSOURCE_HCLK) || \
+                                       ((__SOURCE__) == SYSTICK_CLKSOURCE_HCLK_DIV8))
+/**
+  * @}
+  */
+
+#if (__MPU_PRESENT == 1)
+/** @defgroup CORTEX_MPU_HFNMI_PRIVDEF_Control CORTEX MPU HFNMI and PRIVILEGED Access control
+  * @{
+  */
+#define  MPU_HFNMI_PRIVDEF_NONE      (0x00000000U)
+#define  MPU_HARDFAULT_NMI           (0x00000002U)
+#define  MPU_PRIVILEGED_DEFAULT      (0x00000004U)
+#define  MPU_HFNMI_PRIVDEF           (0x00000006U)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Region_Enable CORTEX MPU Region Enable
+  * @{
+  */
+#define  MPU_REGION_ENABLE           ((uint8_t)0x01)
+#define  MPU_REGION_DISABLE          ((uint8_t)0x00)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Instruction_Access CORTEX MPU Instruction Access
+  * @{
+  */
+#define  MPU_INSTRUCTION_ACCESS_ENABLE      ((uint8_t)0x00)
+#define  MPU_INSTRUCTION_ACCESS_DISABLE     ((uint8_t)0x01)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Access_Shareable CORTEX MPU Instruction Access Shareable
+  * @{
+  */
+#define  MPU_ACCESS_SHAREABLE        ((uint8_t)0x01)
+#define  MPU_ACCESS_NOT_SHAREABLE    ((uint8_t)0x00)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Access_Cacheable CORTEX MPU Instruction Access Cacheable
+  * @{
+  */
+#define  MPU_ACCESS_CACHEABLE        ((uint8_t)0x01)
+#define  MPU_ACCESS_NOT_CACHEABLE    ((uint8_t)0x00)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Access_Bufferable CORTEX MPU Instruction Access Bufferable
+  * @{
+  */
+#define  MPU_ACCESS_BUFFERABLE       ((uint8_t)0x01)
+#define  MPU_ACCESS_NOT_BUFFERABLE   ((uint8_t)0x00)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Region_Size CORTEX MPU Region Size
+  * @{
+  */
+#define   MPU_REGION_SIZE_32B        ((uint8_t)0x04)
+#define   MPU_REGION_SIZE_64B        ((uint8_t)0x05)
+#define   MPU_REGION_SIZE_128B       ((uint8_t)0x06)
+#define   MPU_REGION_SIZE_256B       ((uint8_t)0x07)
+#define   MPU_REGION_SIZE_512B       ((uint8_t)0x08)
+#define   MPU_REGION_SIZE_1KB        ((uint8_t)0x09)
+#define   MPU_REGION_SIZE_2KB        ((uint8_t)0x0A)
+#define   MPU_REGION_SIZE_4KB        ((uint8_t)0x0B)
+#define   MPU_REGION_SIZE_8KB        ((uint8_t)0x0C)
+#define   MPU_REGION_SIZE_16KB       ((uint8_t)0x0D)
+#define   MPU_REGION_SIZE_32KB       ((uint8_t)0x0E)
+#define   MPU_REGION_SIZE_64KB       ((uint8_t)0x0F)
+#define   MPU_REGION_SIZE_128KB      ((uint8_t)0x10)
+#define   MPU_REGION_SIZE_256KB      ((uint8_t)0x11)
+#define   MPU_REGION_SIZE_512KB      ((uint8_t)0x12)
+#define   MPU_REGION_SIZE_1MB        ((uint8_t)0x13)
+#define   MPU_REGION_SIZE_2MB        ((uint8_t)0x14)
+#define   MPU_REGION_SIZE_4MB        ((uint8_t)0x15)
+#define   MPU_REGION_SIZE_8MB        ((uint8_t)0x16)
+#define   MPU_REGION_SIZE_16MB       ((uint8_t)0x17)
+#define   MPU_REGION_SIZE_32MB       ((uint8_t)0x18)
+#define   MPU_REGION_SIZE_64MB       ((uint8_t)0x19)
+#define   MPU_REGION_SIZE_128MB      ((uint8_t)0x1A)
+#define   MPU_REGION_SIZE_256MB      ((uint8_t)0x1B)
+#define   MPU_REGION_SIZE_512MB      ((uint8_t)0x1C)
+#define   MPU_REGION_SIZE_1GB        ((uint8_t)0x1D)
+#define   MPU_REGION_SIZE_2GB        ((uint8_t)0x1E)
+#define   MPU_REGION_SIZE_4GB        ((uint8_t)0x1F)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Region_Permission_Attributes CORTEX MPU Region Permission Attributes
+  * @{
+  */
+#define  MPU_REGION_NO_ACCESS        ((uint8_t)0x00)
+#define  MPU_REGION_PRIV_RW          ((uint8_t)0x01)
+#define  MPU_REGION_PRIV_RW_URO      ((uint8_t)0x02)
+#define  MPU_REGION_FULL_ACCESS      ((uint8_t)0x03)
+#define  MPU_REGION_PRIV_RO          ((uint8_t)0x05)
+#define  MPU_REGION_PRIV_RO_URO      ((uint8_t)0x06)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Region_Number CORTEX MPU Region Number
+  * @{
+  */
+#define  MPU_REGION_NUMBER0          ((uint8_t)0x00)
+#define  MPU_REGION_NUMBER1          ((uint8_t)0x01)
+#define  MPU_REGION_NUMBER2          ((uint8_t)0x02)
+#define  MPU_REGION_NUMBER3          ((uint8_t)0x03)
+#define  MPU_REGION_NUMBER4          ((uint8_t)0x04)
+#define  MPU_REGION_NUMBER5          ((uint8_t)0x05)
+#define  MPU_REGION_NUMBER6          ((uint8_t)0x06)
+#define  MPU_REGION_NUMBER7          ((uint8_t)0x07)
+/**
+  * @}
+  */
+#endif /* __MPU_PRESENT */
+
+
+/**
+  * @}
+  */  
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup CORTEX_Exported_Functions CORTEX Exported Functions
+  * @{
+  */
+  
+/** @defgroup CORTEX_Exported_Functions_Group1 Initialization and Configuration functions 
+ *  @brief    Initialization and Configuration functions
+ * @{
+  */
+void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority);
+void HAL_NVIC_EnableIRQ(IRQn_Type IRQn);
+void HAL_NVIC_DisableIRQ(IRQn_Type IRQn);
+void HAL_NVIC_SystemReset(void);
+uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb);
+/**
+  * @}
+  */
+  
+/** @defgroup CORTEX_Exported_Functions_Group2 Peripheral Control functions
+ *  @brief   Cortex control functions
+ * @{
+ */
+ 
+uint32_t HAL_NVIC_GetPriority(IRQn_Type IRQn);
+uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn);
+void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn);
+void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn);
+void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource);
+void HAL_SYSTICK_IRQHandler(void);
+void HAL_SYSTICK_Callback(void);
+#if (__MPU_PRESENT == 1U)
+void HAL_MPU_Enable(uint32_t MPU_Control);
+void HAL_MPU_Disable(void);
+void HAL_MPU_ConfigRegion(MPU_Region_InitTypeDef *MPU_Init);
+#endif /* __MPU_PRESENT */
+/**
+  * @}
+  */
+  
+  /**
+  * @}
+  */
+
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup CORTEX_Private_Macros CORTEX Private Macros
+  * @{
+  */
+
+#if (__MPU_PRESENT == 1)
+#define IS_MPU_REGION_ENABLE(STATE) (((STATE) == MPU_REGION_ENABLE) || \
+                                     ((STATE) == MPU_REGION_DISABLE))
+
+#define IS_MPU_INSTRUCTION_ACCESS(STATE) (((STATE) == MPU_INSTRUCTION_ACCESS_ENABLE) || \
+                                          ((STATE) == MPU_INSTRUCTION_ACCESS_DISABLE))
+
+#define IS_MPU_ACCESS_SHAREABLE(STATE)   (((STATE) == MPU_ACCESS_SHAREABLE) || \
+                                          ((STATE) == MPU_ACCESS_NOT_SHAREABLE))
+
+#define IS_MPU_ACCESS_CACHEABLE(STATE)   (((STATE) == MPU_ACCESS_CACHEABLE) || \
+                                          ((STATE) == MPU_ACCESS_NOT_CACHEABLE))
+
+#define IS_MPU_ACCESS_BUFFERABLE(STATE)   (((STATE) == MPU_ACCESS_BUFFERABLE) || \
+                                          ((STATE) == MPU_ACCESS_NOT_BUFFERABLE))
+
+#define IS_MPU_REGION_PERMISSION_ATTRIBUTE(TYPE) (((TYPE) == MPU_REGION_NO_ACCESS)   || \
+                                                  ((TYPE) == MPU_REGION_PRIV_RW)     || \
+                                                  ((TYPE) == MPU_REGION_PRIV_RW_URO) || \
+                                                  ((TYPE) == MPU_REGION_FULL_ACCESS) || \
+                                                  ((TYPE) == MPU_REGION_PRIV_RO)     || \
+                                                  ((TYPE) == MPU_REGION_PRIV_RO_URO))
+
+#define IS_MPU_REGION_NUMBER(NUMBER)    (((NUMBER) == MPU_REGION_NUMBER0) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER1) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER2) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER3) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER4) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER5) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER6) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER7))
+
+#define IS_MPU_REGION_SIZE(SIZE)    (((SIZE) == MPU_REGION_SIZE_256B)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_512B)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_1KB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_2KB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_4KB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_8KB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_16KB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_32KB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_64KB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_128KB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_256KB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_512KB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_1MB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_2MB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_4MB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_8MB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_16MB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_32MB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_64MB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_128MB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_256MB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_512MB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_1GB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_2GB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_4GB))
+
+#define IS_MPU_SUB_REGION_DISABLE(SUBREGION)  ((SUBREGION) < (uint16_t)0x00FFU)
+#endif /* __MPU_PRESENT */
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+  
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L0xx_HAL_CORTEX_H */
+ 
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_def.h

@@ -0,0 +1,204 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_def.h
+  * @author  MCD Application Team
+  * @brief   This file contains HAL common defines, enumeration, macros and
+  *          structures definitions.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_DEF
+#define __STM32L0xx_HAL_DEF
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx.h"
+#include "Legacy/stm32_hal_legacy.h"
+#include <stddef.h>
+
+/* Exported types ------------------------------------------------------------*/
+
+/**
+  * @brief  HAL Status structures definition
+  */
+typedef enum
+{
+  HAL_OK       = 0x00U,
+  HAL_ERROR    = 0x01U,
+  HAL_BUSY     = 0x02U,
+  HAL_TIMEOUT  = 0x03U
+} HAL_StatusTypeDef;
+
+/**
+  * @brief  HAL Lock structures definition
+  */
+typedef enum
+{
+  HAL_UNLOCKED = 0x00U,
+  HAL_LOCKED   = 0x01U
+} HAL_LockTypeDef;
+
+/* Exported macro ------------------------------------------------------------*/
+
+#define UNUSED(X) (void)X      /* To avoid gcc/g++ warnings */
+
+#define HAL_MAX_DELAY      0xFFFFFFFFU
+
+#define HAL_IS_BIT_SET(REG, BIT)         (((REG) & (BIT)) == (BIT))
+#define HAL_IS_BIT_CLR(REG, BIT)         (((REG) & (BIT)) == 0U)
+
+#define __HAL_LINKDMA(__HANDLE__, __PPP_DMA_FIELD__, __DMA_HANDLE__)             \
+                        do{                                                    \
+                            (__HANDLE__)->__PPP_DMA_FIELD__ = &(__DMA_HANDLE__); \
+                            (__DMA_HANDLE__).Parent = (__HANDLE__);             \
+                          } while(0)
+
+/** @brief Reset the Handle's State field.
+  * @param __HANDLE__: specifies the Peripheral Handle.
+  * @note  This macro can be used for the following purpose:
+  *          - When the Handle is declared as local variable; before passing it as parameter
+  *            to HAL_PPP_Init() for the first time, it is mandatory to use this macro
+  *            to set to 0 the Handle's "State" field.
+  *            Otherwise, "State" field may have any random value and the first time the function
+  *            HAL_PPP_Init() is called, the low level hardware initialization will be missed
+  *            (i.e. HAL_PPP_MspInit() will not be executed).
+  *          - When there is a need to reconfigure the low level hardware: instead of calling
+  *            HAL_PPP_DeInit() then HAL_PPP_Init(), user can make a call to this macro then HAL_PPP_Init().
+  *            In this later function, when the Handle's "State" field is set to 0, it will execute the function
+  *            HAL_PPP_MspInit() which will reconfigure the low level hardware.
+  * @retval None
+  */
+#define __HAL_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = 0U)
+
+#if (USE_RTOS == 1)
+
+  /* Reserved for future use */
+  #error "USE_RTOS should be 0 in the current HAL release"
+
+#else
+  #define __HAL_LOCK(__HANDLE__)                                               \
+                                do{                                            \
+                                    if((__HANDLE__)->Lock == HAL_LOCKED)       \
+                                    {                                          \
+                                       return HAL_BUSY;                        \
+                                    }                                          \
+                                    else                                       \
+                                    {                                          \
+                                       (__HANDLE__)->Lock = HAL_LOCKED;        \
+                                    }                                          \
+                                  }while (0)
+
+  #define __HAL_UNLOCK(__HANDLE__)                                             \
+                                  do{                                          \
+                                      (__HANDLE__)->Lock = HAL_UNLOCKED;       \
+                                    }while (0)
+#endif /* USE_RTOS */
+
+#if defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) /* ARM Compiler V6 */
+  #ifndef __weak
+    #define __weak  __attribute__((weak))
+  #endif
+  #ifndef __packed
+    #define __packed  __attribute__((packed))
+  #endif
+#elif defined ( __GNUC__ ) && !defined (__CC_ARM) /* GNU Compiler */
+  #ifndef __weak
+    #define __weak   __attribute__((weak))
+  #endif /* __weak */
+  #ifndef __packed
+    #define __packed __attribute__((__packed__))
+  #endif /* __packed */
+
+  #define __NOINLINE __attribute__ ( (noinline) )
+
+#endif /* __GNUC__ */
+
+
+/* Macro to get variable aligned on 4-bytes, for __ICCARM__ the directive "#pragma data_alignment=4" must be used instead */
+#if defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) /* ARM Compiler V6 */
+  #ifndef __ALIGN_BEGIN
+    #define __ALIGN_BEGIN
+  #endif
+  #ifndef __ALIGN_END
+    #define __ALIGN_END      __attribute__ ((aligned (4)))
+  #endif
+#elif defined ( __GNUC__ ) && !defined (__CC_ARM) /* GNU Compiler */
+  #ifndef __ALIGN_END
+    #define __ALIGN_END    __attribute__ ((aligned (4)))
+  #endif /* __ALIGN_END */
+  #ifndef __ALIGN_BEGIN
+    #define __ALIGN_BEGIN
+  #endif /* __ALIGN_BEGIN */
+#else
+  #ifndef __ALIGN_END
+    #define __ALIGN_END
+  #endif /* __ALIGN_END */
+  #ifndef __ALIGN_BEGIN
+    #if defined   (__CC_ARM)      /* ARM Compiler V5*/
+      #define __ALIGN_BEGIN    __align(4)
+    #elif defined (__ICCARM__)    /* IAR Compiler */
+      #define __ALIGN_BEGIN
+    #endif /* __CC_ARM */
+  #endif /* __ALIGN_BEGIN */
+#endif /* __GNUC__ */
+
+/**
+  * @brief  __RAM_FUNC definition
+  */
+#if defined ( __CC_ARM   ) || (defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050))
+/* ARM Compiler V4/V5 and V6
+   --------------------------
+   RAM functions are defined using the toolchain options.
+   Functions that are executed in RAM should reside in a separate source module.
+   Using the 'Options for File' dialog you can simply change the 'Code / Const'
+   area of a module to a memory space in physical RAM.
+   Available memory areas are declared in the 'Target' tab of the 'Options for Target'
+   dialog.
+*/
+#define __RAM_FUNC
+
+#define __NOINLINE __attribute__ ( (noinline) )
+
+
+#elif defined ( __ICCARM__ )
+/* ICCARM Compiler
+   ---------------
+   RAM functions are defined using a specific toolchain keyword "__ramfunc".
+*/
+#define __RAM_FUNC __ramfunc
+
+#define __NOINLINE _Pragma("optimize = no_inline")
+
+#elif defined   (  __GNUC__  )
+/* GNU Compiler
+   ------------
+  RAM functions are defined using a specific toolchain attribute
+   "__attribute__((section(".RamFunc")))".
+*/
+#define __RAM_FUNC  __attribute__((section(".RamFunc")))
+
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* ___STM32L0xx_HAL_DEF */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_dma.h

@@ -0,0 +1,675 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_dma.h
+  * @author  MCD Application Team
+  * @brief   Header file of DMA HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32L0xx_HAL_DMA_H
+#define STM32L0xx_HAL_DMA_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup DMA
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup DMA_Exported_Types DMA Exported Types
+  * @{
+  */
+
+/**
+  * @brief  DMA Configuration Structure definition
+  */
+typedef struct
+{
+  uint32_t Request;                   /*!< Specifies the request selected for the specified channel.
+                                           This parameter can be a value of @ref DMA_request */
+
+  uint32_t Direction;                 /*!< Specifies if the data will be transferred from memory to peripheral,
+                                           from memory to memory or from peripheral to memory.
+                                           This parameter can be a value of @ref DMA_Data_transfer_direction */
+
+  uint32_t PeriphInc;                 /*!< Specifies whether the Peripheral address register should be incremented or not.
+                                           This parameter can be a value of @ref DMA_Peripheral_incremented_mode */
+
+  uint32_t MemInc;                    /*!< Specifies whether the memory address register should be incremented or not.
+                                           This parameter can be a value of @ref DMA_Memory_incremented_mode */
+
+  uint32_t PeriphDataAlignment;       /*!< Specifies the Peripheral data width.
+                                           This parameter can be a value of @ref DMA_Peripheral_data_size */
+
+  uint32_t MemDataAlignment;          /*!< Specifies the Memory data width.
+                                           This parameter can be a value of @ref DMA_Memory_data_size */
+
+  uint32_t Mode;                      /*!< Specifies the operation mode of the DMAy Channelx.
+                                           This parameter can be a value of @ref DMA_mode
+                                           @note The circular buffer mode cannot be used if the memory-to-memory
+                                                 data transfer is configured on the selected Channel */
+
+  uint32_t Priority;                  /*!< Specifies the software priority for the DMAy Channelx.
+                                           This parameter can be a value of @ref DMA_Priority_level */
+} DMA_InitTypeDef;
+
+/**
+  * @brief  HAL DMA State structures definition
+  */
+typedef enum
+{
+  HAL_DMA_STATE_RESET             = 0x00U,  /*!< DMA not yet initialized or disabled    */
+  HAL_DMA_STATE_READY             = 0x01U,  /*!< DMA initialized and ready for use      */
+  HAL_DMA_STATE_BUSY              = 0x02U,  /*!< DMA process is ongoing                 */
+  HAL_DMA_STATE_TIMEOUT           = 0x03U,  /*!< DMA timeout state                      */
+}HAL_DMA_StateTypeDef;
+
+/**
+  * @brief  HAL DMA Error Code structure definition
+  */
+typedef enum
+{
+  HAL_DMA_FULL_TRANSFER      = 0x00U,    /*!< Full transfer     */
+  HAL_DMA_HALF_TRANSFER      = 0x01U     /*!< Half Transfer     */
+}HAL_DMA_LevelCompleteTypeDef;
+
+
+/**
+  * @brief  HAL DMA Callback ID structure definition
+  */
+typedef enum
+{
+  HAL_DMA_XFER_CPLT_CB_ID          = 0x00U,    /*!< Full transfer     */
+  HAL_DMA_XFER_HALFCPLT_CB_ID      = 0x01U,    /*!< Half transfer     */
+  HAL_DMA_XFER_ERROR_CB_ID         = 0x02U,    /*!< Error             */
+  HAL_DMA_XFER_ABORT_CB_ID         = 0x03U,    /*!< Abort             */
+  HAL_DMA_XFER_ALL_CB_ID           = 0x04U     /*!< All               */
+}HAL_DMA_CallbackIDTypeDef;
+
+/**
+  * @brief  DMA handle Structure definition
+  */
+typedef struct __DMA_HandleTypeDef
+{
+  DMA_Channel_TypeDef    *Instance;                                                  /*!< Register base address                */
+
+  DMA_InitTypeDef       Init;                                                        /*!< DMA communication parameters         */
+
+  HAL_LockTypeDef       Lock;                                                        /*!< DMA locking object                   */
+
+  __IO HAL_DMA_StateTypeDef  State;                                                  /*!< DMA transfer state                   */
+
+  void                  *Parent;                                                     /*!< Parent object state                  */
+
+  void                  (* XferCpltCallback)(struct __DMA_HandleTypeDef * hdma);     /*!< DMA transfer complete callback       */
+
+  void                  (* XferHalfCpltCallback)(struct __DMA_HandleTypeDef * hdma); /*!< DMA Half transfer complete callback  */
+
+  void                  (* XferErrorCallback)(struct __DMA_HandleTypeDef * hdma);    /*!< DMA transfer error callback          */
+
+  void                  (* XferAbortCallback)( struct __DMA_HandleTypeDef * hdma);   /*!< DMA transfer abort callback          */
+
+  __IO uint32_t          ErrorCode;                                                  /*!< DMA Error code                       */
+
+  DMA_TypeDef            *DmaBaseAddress;                                            /*!< DMA Channel Base Address             */
+
+  uint32_t               ChannelIndex;                                               /*!< DMA Channel Index                    */
+
+}DMA_HandleTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup DMA_Exported_Constants DMA Exported Constants
+  * @{
+  */
+
+/** @defgroup DMA_Error_Code DMA Error Code
+  * @{
+  */
+#define HAL_DMA_ERROR_NONE                 0x00000000U    /*!< No error                                */
+#define HAL_DMA_ERROR_TE                   0x00000001U    /*!< Transfer error                          */
+#define HAL_DMA_ERROR_NO_XFER              0x00000004U    /*!< Abort requested with no Xfer ongoing    */
+#define HAL_DMA_ERROR_TIMEOUT              0x00000020U    /*!< Timeout error                           */
+#define HAL_DMA_ERROR_NOT_SUPPORTED        0x00000100U    /*!< Not supported mode                      */
+
+/**
+  * @}
+  */
+
+/** @defgroup DMA_request DMA request
+  * @{
+  */
+
+#if defined (STM32L010x4) || defined (STM32L010x6) || defined (STM32L010x8) || defined (STM32L010xC)
+
+#define DMA_REQUEST_0                     0U
+#define DMA_REQUEST_1                     1U
+#define DMA_REQUEST_4                     4U
+#define DMA_REQUEST_5                     5U
+#define DMA_REQUEST_6                     6U
+#define DMA_REQUEST_8                     8U
+
+#define IS_DMA_ALL_REQUEST(REQUEST) (((REQUEST) == DMA_REQUEST_0) || \
+                                     ((REQUEST) == DMA_REQUEST_1) || \
+                                     ((REQUEST) == DMA_REQUEST_4) || \
+                                     ((REQUEST) == DMA_REQUEST_5) || \
+                                     ((REQUEST) == DMA_REQUEST_6) || \
+                                     ((REQUEST) == DMA_REQUEST_8))
+
+/* STM32L010x4 || STM32L010x6 || STM32L010x8 || STM32L010xC */
+
+#elif defined (STM32L021xx) || defined (STM32L041xx) || defined (STM32L062xx) || defined (STM32L063xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+
+#define DMA_REQUEST_0                     0U
+#define DMA_REQUEST_1                     1U
+#define DMA_REQUEST_2                     2U
+#define DMA_REQUEST_3                     3U
+#define DMA_REQUEST_4                     4U
+#define DMA_REQUEST_5                     5U
+#define DMA_REQUEST_6                     6U
+#define DMA_REQUEST_7                     7U
+#define DMA_REQUEST_8                     8U
+#define DMA_REQUEST_9                     9U
+#define DMA_REQUEST_10                   10U
+#define DMA_REQUEST_11                   11U  /* AES product only */
+#define DMA_REQUEST_12                   12U
+#define DMA_REQUEST_13                   13U
+#define DMA_REQUEST_14                   14U
+#define DMA_REQUEST_15                   15U
+
+#define IS_DMA_ALL_REQUEST(REQUEST) (((REQUEST) == DMA_REQUEST_0) || \
+                                     ((REQUEST) == DMA_REQUEST_1) || \
+                                     ((REQUEST) == DMA_REQUEST_2) || \
+                                     ((REQUEST) == DMA_REQUEST_3) || \
+                                     ((REQUEST) == DMA_REQUEST_4) || \
+                                     ((REQUEST) == DMA_REQUEST_5) || \
+                                     ((REQUEST) == DMA_REQUEST_6) || \
+                                     ((REQUEST) == DMA_REQUEST_7) || \
+                                     ((REQUEST) == DMA_REQUEST_8) || \
+                                     ((REQUEST) == DMA_REQUEST_9) || \
+                                     ((REQUEST) == DMA_REQUEST_10) || \
+                                     ((REQUEST) == DMA_REQUEST_11) || \
+                                     ((REQUEST) == DMA_REQUEST_12) || \
+                                     ((REQUEST) == DMA_REQUEST_13) || \
+                                     ((REQUEST) == DMA_REQUEST_14) || \
+                                     ((REQUEST) == DMA_REQUEST_15))
+
+/* (STM32L021xx) || (STM32L041xx) || (STM32L062xx) || (STM32L063xx) || (STM32L081xx) || (STM32L082xx) || (STM32L083xx) */
+
+#else
+
+#define DMA_REQUEST_0                     0U
+#define DMA_REQUEST_1                     1U
+#define DMA_REQUEST_2                     2U
+#define DMA_REQUEST_3                     3U
+#define DMA_REQUEST_4                     4U
+#define DMA_REQUEST_5                     5U
+#define DMA_REQUEST_6                     6U
+#define DMA_REQUEST_7                     7U
+#define DMA_REQUEST_8                     8U
+#define DMA_REQUEST_9                     9U
+#define DMA_REQUEST_10                   10U
+#define DMA_REQUEST_12                   12U
+#define DMA_REQUEST_13                   13U
+#define DMA_REQUEST_14                   14U
+#define DMA_REQUEST_15                   15U
+
+#define IS_DMA_ALL_REQUEST(REQUEST) (((REQUEST) == DMA_REQUEST_0) || \
+                                     ((REQUEST) == DMA_REQUEST_1) || \
+                                     ((REQUEST) == DMA_REQUEST_2) || \
+                                     ((REQUEST) == DMA_REQUEST_3) || \
+                                     ((REQUEST) == DMA_REQUEST_4) || \
+                                     ((REQUEST) == DMA_REQUEST_5) || \
+                                     ((REQUEST) == DMA_REQUEST_6) || \
+                                     ((REQUEST) == DMA_REQUEST_7) || \
+                                     ((REQUEST) == DMA_REQUEST_8) || \
+                                     ((REQUEST) == DMA_REQUEST_9) || \
+                                     ((REQUEST) == DMA_REQUEST_10) || \
+                                     ((REQUEST) == DMA_REQUEST_12) || \
+                                     ((REQUEST) == DMA_REQUEST_13) || \
+                                     ((REQUEST) == DMA_REQUEST_14) || \
+                                     ((REQUEST) == DMA_REQUEST_15))
+
+#endif /* (STM32L031xx) || (STM32L051xx) || (STM32L052xx) || (STM32L053xx) || (STM32L071xx) || (STM32L072xx) || (STM32L073xx) */
+
+
+
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Data_transfer_direction DMA Data transfer direction
+  * @{
+  */
+#define DMA_PERIPH_TO_MEMORY         0x00000000U        /*!< Peripheral to memory direction */
+#define DMA_MEMORY_TO_PERIPH         DMA_CCR_DIR        /*!< Memory to peripheral direction */
+#define DMA_MEMORY_TO_MEMORY         DMA_CCR_MEM2MEM    /*!< Memory to memory direction     */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Peripheral_incremented_mode DMA Peripheral incremented mode
+  * @{
+  */
+#define DMA_PINC_ENABLE              DMA_CCR_PINC  /*!< Peripheral increment mode Enable */
+#define DMA_PINC_DISABLE             0x00000000U   /*!< Peripheral increment mode Disable */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Memory_incremented_mode DMA Memory incremented mode
+  * @{
+  */
+#define DMA_MINC_ENABLE              DMA_CCR_MINC   /*!< Memory increment mode Enable  */
+#define DMA_MINC_DISABLE             0x00000000U    /*!< Memory increment mode Disable */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Peripheral_data_size DMA Peripheral data size
+  * @{
+  */
+#define DMA_PDATAALIGN_BYTE          0x00000000U     /*!< Peripheral data alignment : Byte     */
+#define DMA_PDATAALIGN_HALFWORD      DMA_CCR_PSIZE_0 /*!< Peripheral data alignment : HalfWord */
+#define DMA_PDATAALIGN_WORD          DMA_CCR_PSIZE_1 /*!< Peripheral data alignment : Word     */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Memory_data_size DMA Memory data size
+  * @{
+  */
+#define DMA_MDATAALIGN_BYTE          0x00000000U     /*!< Memory data alignment : Byte     */
+#define DMA_MDATAALIGN_HALFWORD      DMA_CCR_MSIZE_0 /*!< Memory data alignment : HalfWord */
+#define DMA_MDATAALIGN_WORD          DMA_CCR_MSIZE_1 /*!< Memory data alignment : Word     */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_mode DMA mode
+  * @{
+  */
+#define DMA_NORMAL                   0x00000000U     /*!< Normal mode                  */
+#define DMA_CIRCULAR                 DMA_CCR_CIRC    /*!< Circular mode                */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Priority_level DMA Priority level
+  * @{
+  */
+#define DMA_PRIORITY_LOW             0x00000000U      /*!< Priority level : Low       */
+#define DMA_PRIORITY_MEDIUM          DMA_CCR_PL_0     /*!< Priority level : Medium    */
+#define DMA_PRIORITY_HIGH            DMA_CCR_PL_1     /*!< Priority level : High      */
+#define DMA_PRIORITY_VERY_HIGH       DMA_CCR_PL       /*!< Priority level : Very_High */
+/**
+  * @}
+  */
+
+
+/** @defgroup DMA_interrupt_enable_definitions DMA interrupt enable definitions
+  * @{
+  */
+#define DMA_IT_TC                         DMA_CCR_TCIE
+#define DMA_IT_HT                         DMA_CCR_HTIE
+#define DMA_IT_TE                         DMA_CCR_TEIE
+/**
+  * @}
+  */
+
+/** @defgroup DMA_flag_definitions DMA flag definitions
+  * @{
+  */
+#define DMA_FLAG_GL1                      DMA_ISR_GIF1
+#define DMA_FLAG_TC1                      DMA_ISR_TCIF1
+#define DMA_FLAG_HT1                      DMA_ISR_HTIF1
+#define DMA_FLAG_TE1                      DMA_ISR_TEIF1
+#define DMA_FLAG_GL2                      DMA_ISR_GIF2
+#define DMA_FLAG_TC2                      DMA_ISR_TCIF2
+#define DMA_FLAG_HT2                      DMA_ISR_HTIF2
+#define DMA_FLAG_TE2                      DMA_ISR_TEIF2
+#define DMA_FLAG_GL3                      DMA_ISR_GIF3
+#define DMA_FLAG_TC3                      DMA_ISR_TCIF3
+#define DMA_FLAG_HT3                      DMA_ISR_HTIF3
+#define DMA_FLAG_TE3                      DMA_ISR_TEIF3
+#define DMA_FLAG_GL4                      DMA_ISR_GIF4
+#define DMA_FLAG_TC4                      DMA_ISR_TCIF4
+#define DMA_FLAG_HT4                      DMA_ISR_HTIF4
+#define DMA_FLAG_TE4                      DMA_ISR_TEIF4
+#define DMA_FLAG_GL5                      DMA_ISR_GIF5
+#define DMA_FLAG_TC5                      DMA_ISR_TCIF5
+#define DMA_FLAG_HT5                      DMA_ISR_HTIF5
+#define DMA_FLAG_TE5                      DMA_ISR_TEIF5
+#define DMA_FLAG_GL6                      DMA_ISR_GIF6
+#define DMA_FLAG_TC6                      DMA_ISR_TCIF6
+#define DMA_FLAG_HT6                      DMA_ISR_HTIF6
+#define DMA_FLAG_TE6                      DMA_ISR_TEIF6
+#define DMA_FLAG_GL7                      DMA_ISR_GIF7
+#define DMA_FLAG_TC7                      DMA_ISR_TCIF7
+#define DMA_FLAG_HT7                      DMA_ISR_HTIF7
+#define DMA_FLAG_TE7                      DMA_ISR_TEIF7
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup DMA_Exported_Macros DMA Exported Macros
+  * @{
+  */
+
+/** @brief  Reset DMA handle state
+  * @param  __HANDLE__ DMA handle
+  * @retval None
+  */
+#define __HAL_DMA_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_DMA_STATE_RESET)
+
+/**
+  * @brief  Enable the specified DMA Channel.
+  * @param  __HANDLE__ DMA handle
+  * @retval None
+  */
+#define __HAL_DMA_ENABLE(__HANDLE__)        ((__HANDLE__)->Instance->CCR |=  DMA_CCR_EN)
+
+/**
+  * @brief  Disable the specified DMA Channel.
+  * @param  __HANDLE__ DMA handle
+  * @retval None
+  */
+#define __HAL_DMA_DISABLE(__HANDLE__)       ((__HANDLE__)->Instance->CCR &=  ~DMA_CCR_EN)
+
+
+/* Interrupt & Flag management */
+
+/**
+  * @brief  Return the current DMA Channel transfer complete flag.
+  * @param  __HANDLE__: DMA handle
+  * @retval The specified transfer complete flag index.
+  */
+
+#if defined (STM32L010x4) || defined (STM32L011xx) || defined (STM32L021xx)
+#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TC1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TC2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TC3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TC4 :\
+ DMA_FLAG_TC5)
+#else
+#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TC1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TC2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TC3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TC4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TC5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TC6 :\
+   DMA_FLAG_TC7)
+#endif
+/**
+  * @brief  Return the current DMA Channel half transfer complete flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified half transfer complete flag index.
+  */
+#if defined (STM32L010x4) || defined (STM32L011xx) || defined (STM32L021xx)
+#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_HT1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_HT2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_HT3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_HT4 :\
+ DMA_FLAG_HT5)
+#else
+#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_HT1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_HT2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_HT3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_HT4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_HT5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_HT6 :\
+   DMA_FLAG_HT7)
+#endif
+/**
+  * @brief  Returns the current DMA Channel transfer error flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#if defined (STM32L010x4) || defined (STM32L011xx) || defined (STM32L021xx)
+#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TE1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TE2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TE3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TE4 :\
+ DMA_FLAG_TE5)
+#else
+#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TE1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TE2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TE3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TE4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TE5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TE6 :\
+   DMA_FLAG_TE7)
+#endif
+/**
+  * @brief  Returns the current DMA Channel Global interrupt flag.
+  * @param  __HANDLE__ DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#if defined (STM32L010x4) || defined (STM32L011xx) || defined (STM32L021xx)
+#define __HAL_DMA_GET_GI_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_ISR_GIF1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_ISR_GIF2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_ISR_GIF3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_ISR_GIF4 :\
+   DMA_ISR_GIF5)
+#else
+#define __HAL_DMA_GET_GI_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_ISR_GIF1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_ISR_GIF2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_ISR_GIF3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_ISR_GIF4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_ISR_GIF5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_ISR_GIF6 :\
+   DMA_ISR_GIF7)
+#endif
+/**
+  * @brief  Get the DMA Channel pending flags.
+  * @param  __HANDLE__ DMA handle
+  * @param  __FLAG__ Get the specified flag.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCIFx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTIFx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEIFx:  Transfer error flag
+  *            @arg DMA_ISR_GIFx: Global interrupt flag
+  *         Where x can be 0_4, 1_5, 2_6 or 3_7 to select the DMA Channel flag.
+  * @retval The state of FLAG (SET or RESET).
+  */
+#define __HAL_DMA_GET_FLAG(__HANDLE__, __FLAG__) (DMA1->ISR & (__FLAG__))
+
+/**
+  * @brief  Clears the DMA Channel pending flags.
+  * @param  __HANDLE__ DMA handle
+  * @param  __FLAG__ specifies the flag to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *            @arg DMA_FLAG_GLx:  Global interrupt flag
+  *         Where x can be 0_4, 1_5, 2_6 or 3_7 to select the DMA Channel flag.
+  * @retval None
+  */
+#define __HAL_DMA_CLEAR_FLAG(__HANDLE__, __FLAG__) (DMA1->IFCR = (__FLAG__))
+
+/**
+  * @brief  Enable the specified DMA Channel interrupts.
+  * @param  __HANDLE__ DMA handle
+  * @param __INTERRUPT__: specifies the DMA interrupt sources to be enabled or disabled.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_IT_TC:  Transfer complete interrupt mask
+  *            @arg DMA_IT_HT:  Half transfer complete interrupt mask
+  *            @arg DMA_IT_TE:  Transfer error interrupt mask
+  * @retval None
+  */
+#define __HAL_DMA_ENABLE_IT(__HANDLE__, __INTERRUPT__)   ((__HANDLE__)->Instance->CCR |= (__INTERRUPT__))
+
+/**
+  * @brief  Disable the specified DMA Channel interrupts.
+  * @param  __HANDLE__ DMA handle
+  * @param  __INTERRUPT__ specifies the DMA interrupt sources to be enabled or disabled. 
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_IT_TC:  Transfer complete interrupt mask
+  *            @arg DMA_IT_HT:  Half transfer complete interrupt mask
+  *            @arg DMA_IT_TE:  Transfer error interrupt mask
+  * @retval None
+  */
+#define __HAL_DMA_DISABLE_IT(__HANDLE__, __INTERRUPT__)  ((__HANDLE__)->Instance->CCR &= ~(__INTERRUPT__))
+
+/**
+  * @brief  Check whether the specified DMA Channel interrupt is enabled or not.
+  * @param  __HANDLE__ DMA handle
+  * @param  __INTERRUPT__ specifies the DMA interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg DMA_IT_TC:  Transfer complete interrupt mask
+  *            @arg DMA_IT_HT:  Half transfer complete interrupt mask
+  *            @arg DMA_IT_TE:  Transfer error interrupt mask
+  * @retval The state of DMA_IT (SET or RESET).
+  */
+#define __HAL_DMA_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)  (((__HANDLE__)->Instance->CCR & (__INTERRUPT__)))
+
+/**
+  * @brief  Return the number of remaining data units in the current DMA Channel transfer.
+  * @param  __HANDLE__ DMA handle
+  * @retval The number of remaining data units in the current DMA Channel transfer.
+  */
+#define __HAL_DMA_GET_COUNTER(__HANDLE__) ((__HANDLE__)->Instance->CNDTR)
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup DMA_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup DMA_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization and de-initialization functions *****************************/
+HAL_StatusTypeDef HAL_DMA_Init(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_DeInit (DMA_HandleTypeDef *hdma);
+/**
+  * @}
+  */
+
+/** @addtogroup DMA_Exported_Functions_Group2
+  * @{
+  */
+/* IO operation functions *****************************************************/
+HAL_StatusTypeDef HAL_DMA_Start (DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
+HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
+HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_Abort_IT(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, HAL_DMA_LevelCompleteTypeDef CompleteLevel, uint32_t Timeout);
+void HAL_DMA_IRQHandler(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_RegisterCallback(DMA_HandleTypeDef *hdma, HAL_DMA_CallbackIDTypeDef CallbackID, void (* pCallback)( DMA_HandleTypeDef * _hdma));
+HAL_StatusTypeDef HAL_DMA_UnRegisterCallback(DMA_HandleTypeDef *hdma, HAL_DMA_CallbackIDTypeDef CallbackID);
+
+/**
+  * @}
+  */
+
+/** @addtogroup DMA_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral State and Error functions ***************************************/
+HAL_DMA_StateTypeDef HAL_DMA_GetState(DMA_HandleTypeDef *hdma);
+uint32_t             HAL_DMA_GetError(DMA_HandleTypeDef *hdma);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Define the private group ***********************************/
+/**************************************************************/
+/** @defgroup DMA_Private DMA Private
+  * @{
+  */
+
+#define IS_DMA_DIRECTION(DIRECTION) (((DIRECTION) == DMA_PERIPH_TO_MEMORY ) || \
+                                     ((DIRECTION) == DMA_MEMORY_TO_PERIPH)  || \
+                                     ((DIRECTION) == DMA_MEMORY_TO_MEMORY))
+
+#define IS_DMA_BUFFER_SIZE(SIZE) (((SIZE) >= 0x1U) && ((SIZE) < 0x10000U))
+
+#define IS_DMA_PERIPHERAL_INC_STATE(STATE) (((STATE) == DMA_PINC_ENABLE) || \
+                                            ((STATE) == DMA_PINC_DISABLE))
+
+#define IS_DMA_MEMORY_INC_STATE(STATE) (((STATE) == DMA_MINC_ENABLE)  || \
+                                        ((STATE) == DMA_MINC_DISABLE))
+
+#define IS_DMA_PERIPHERAL_DATA_SIZE(SIZE) (((SIZE) == DMA_PDATAALIGN_BYTE)     || \
+                                           ((SIZE) == DMA_PDATAALIGN_HALFWORD) || \
+                                           ((SIZE) == DMA_PDATAALIGN_WORD))
+
+#define IS_DMA_MEMORY_DATA_SIZE(SIZE) (((SIZE) == DMA_MDATAALIGN_BYTE)     || \
+                                       ((SIZE) == DMA_MDATAALIGN_HALFWORD) || \
+                                       ((SIZE) == DMA_MDATAALIGN_WORD ))
+
+#define IS_DMA_MODE(MODE) (((MODE) == DMA_NORMAL )  || \
+                           ((MODE) == DMA_CIRCULAR))
+
+#define IS_DMA_PRIORITY(PRIORITY) (((PRIORITY) == DMA_PRIORITY_LOW )   || \
+                                   ((PRIORITY) == DMA_PRIORITY_MEDIUM) || \
+                                   ((PRIORITY) == DMA_PRIORITY_HIGH)   || \
+                                   ((PRIORITY) == DMA_PRIORITY_VERY_HIGH))
+
+/**
+  * @}
+  */
+/**************************************************************/
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32L0xx_HAL_DMA_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_exti.h

@@ -0,0 +1,342 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_ll_exti.h
+  * @author  MCD Application Team
+  * @brief   Header file of EXTI LL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2020 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_EXTI_H
+#define __STM32L0xx_HAL_EXTI_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup EXTI EXTI
+  * @brief EXTI HAL module driver
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup EXTI_Exported_Types EXTI Exported Types
+  * @{
+  */
+typedef enum
+{
+  HAL_EXTI_COMMON_CB_ID          = 0x00U,
+  HAL_EXTI_RISING_CB_ID          = 0x01U,
+  HAL_EXTI_FALLING_CB_ID         = 0x02U,
+} EXTI_CallbackIDTypeDef;
+
+
+/**
+  * @brief  EXTI Handle structure definition
+  */
+typedef struct
+{
+  uint32_t Line;                    /*!<  Exti line number */
+  void (* PendingCallback)(void);   /*!<  Exti pending callback */
+} EXTI_HandleTypeDef;
+
+/**
+  * @brief  EXTI Configuration structure definition
+  */
+typedef struct
+{
+  uint32_t Line;      /*!< The Exti line to be configured. This parameter
+                           can be a value of @ref EXTI_Line */
+  uint32_t Mode;      /*!< The Exit Mode to be configured for a core.
+                           This parameter can be a combination of @ref EXTI_Mode */
+  uint32_t Trigger;   /*!< The Exti Trigger to be configured. This parameter
+                           can be a value of @ref EXTI_Trigger */
+  uint32_t GPIOSel;   /*!< The Exti GPIO multiplexer selection to be configured.
+                           This parameter is only possible for line 0 to 15. It
+                           can be a value of @ref EXTI_GPIOSel */
+} EXTI_ConfigTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup EXTI_Exported_Constants EXTI Exported Constants
+  * @{
+  */
+
+/** @defgroup EXTI_Line  EXTI Line
+  * @{
+  */
+
+
+#define EXTI_LINE_0                        (EXTI_GPIO       | 0x00u)    /*!< External interrupt line 0 */
+#define EXTI_LINE_1                        (EXTI_GPIO       | 0x01u)    /*!< External interrupt line 1 */
+#define EXTI_LINE_2                        (EXTI_GPIO       | 0x02u)    /*!< External interrupt line 2 */
+#define EXTI_LINE_3                        (EXTI_GPIO       | 0x03u)    /*!< External interrupt line 3 */
+#define EXTI_LINE_4                        (EXTI_GPIO       | 0x04u)    /*!< External interrupt line 4 */
+#define EXTI_LINE_5                        (EXTI_GPIO       | 0x05u)    /*!< External interrupt line 5 */
+#define EXTI_LINE_6                        (EXTI_GPIO       | 0x06u)    /*!< External interrupt line 6 */
+#define EXTI_LINE_7                        (EXTI_GPIO       | 0x07u)    /*!< External interrupt line 7 */
+#define EXTI_LINE_8                        (EXTI_GPIO       | 0x08u)    /*!< External interrupt line 8 */
+#define EXTI_LINE_9                        (EXTI_GPIO       | 0x09u)    /*!< External interrupt line 9 */
+#define EXTI_LINE_10                       (EXTI_GPIO       | 0x0Au)    /*!< External interrupt line 10 */
+#define EXTI_LINE_11                       (EXTI_GPIO       | 0x0Bu)    /*!< External interrupt line 11 */
+#define EXTI_LINE_12                       (EXTI_GPIO       | 0x0Cu)    /*!< External interrupt line 12 */
+#define EXTI_LINE_13                       (EXTI_GPIO       | 0x0Du)    /*!< External interrupt line 13 */
+#define EXTI_LINE_14                       (EXTI_GPIO       | 0x0Eu)    /*!< External interrupt line 14 */
+#define EXTI_LINE_15                       (EXTI_GPIO       | 0x0Fu)    /*!< External interrupt line 15 */
+#if defined(EXTI_IMR_IM16)
+#define EXTI_LINE_16                       (EXTI_CONFIG     | 0x10u)    /*!< External interrupt line 16 Connected to the PVD Output */
+#else
+#define EXTI_LINE_16                       (EXTI_RESERVED   | 0x10u)    /*!< No interrupt supported in this line */
+#endif /* EXTI_IMR_IM16 */
+#define EXTI_LINE_17                       (EXTI_CONFIG     | 0x11u)    /*!< External interrupt line 17 Connected to the RTC Alarm event */
+#if defined(EXTI_IMR_IM18)
+#define EXTI_LINE_18                       (EXTI_DIRECT     | 0x12u)    /*!< External interrupt line 18 Connected to the USB Wakeup from suspend event */
+#else
+#define EXTI_LINE_18                       (EXTI_RESERVED   | 0x12u)    /*!< No interrupt supported in this line */
+#endif /* EXTI_IMR_IM18 */
+#define EXTI_LINE_19                       (EXTI_CONFIG     | 0x13u)    /*!< External interrupt line 19 Connected to the RTC Tamper and Time Stamp events or CSS_LSE */
+#define EXTI_LINE_20                       (EXTI_CONFIG     | 0x14u)    /*!< External interrupt line 20 Connected to the RTC wakeup timer */
+#if defined(EXTI_IMR_IM21)
+#define EXTI_LINE_21                       (EXTI_CONFIG     | 0x15u)    /*!< External interrupt line 21 Connected to the Comparator 1 output */
+#else
+#define EXTI_LINE_21                       (EXTI_RESERVED   | 0x15u)    /*!< No interrupt supported in this line */
+#endif /* EXTI_IMR_IM21 */
+#if defined(EXTI_IMR_IM22)
+#define EXTI_LINE_22                       (EXTI_CONFIG     | 0x16u)    /*!< External interrupt line 22 Connected to the Comparator 2 output */
+#else
+#define EXTI_LINE_22                       (EXTI_RESERVED   | 0x16u)    /*!< No interrupt supported in this line */
+#endif /* EXTI_IMR_IM22 */
+#define EXTI_LINE_23                       (EXTI_DIRECT     | 0x17u)    /*!< External interrupt line 23 Connected to the internal I2C1 wakeup event */
+#if defined(EXTI_IMR_IM24)
+#define EXTI_LINE_24                       (EXTI_DIRECT     | 0x18u)    /*!< External interrupt line 24 Connected to the internal I2C3 wakeup event */
+#else
+#define EXTI_LINE_24                       (EXTI_RESERVED   | 0x18u)    /*!< No interrupt supported in this line */
+#endif /* EXTI_IMR_IM24 */
+#if defined(EXTI_IMR_IM25)
+#define EXTI_LINE_25                       (EXTI_DIRECT     | 0x19u)    /*!< External interrupt line 25 Connected to the internal USART1 wakeup event */
+#else
+#define EXTI_LINE_25                       (EXTI_RESERVED   | 0x19u)    /*!< No interrupt supported in this line */
+#endif /* EXTI_IMR_IM25 */
+#define EXTI_LINE_26                       (EXTI_DIRECT     | 0x1Au)    /*!< External interrupt line 26 Connected to the internal USART2 wakeup event */
+#define EXTI_LINE_27                       (EXTI_RESERVED   | 0x1Bu)    /*!< No interrupt supported in this line */
+#define EXTI_LINE_28                       (EXTI_DIRECT     | 0x1Cu)    /*!< External interrupt line 28 Connected to the LPUART1 Wakeup event */
+#define EXTI_LINE_29                       (EXTI_DIRECT     | 0x1Du)    /*!< External interrupt line 29 Connected to the LPTIM1 Wakeup event */
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Mode  EXTI Mode
+  * @{
+  */
+#define EXTI_MODE_NONE                      0x00000000u
+#define EXTI_MODE_INTERRUPT                 0x00000001u
+#define EXTI_MODE_EVENT                     0x00000002u
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Trigger  EXTI Trigger
+  * @{
+  */
+#define EXTI_TRIGGER_NONE                   0x00000000u
+#define EXTI_TRIGGER_RISING                 0x00000001u
+#define EXTI_TRIGGER_FALLING                0x00000002u
+#define EXTI_TRIGGER_RISING_FALLING         (EXTI_TRIGGER_RISING | EXTI_TRIGGER_FALLING)
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_GPIOSel  EXTI GPIOSel
+  * @brief
+  * @{
+  */
+#define EXTI_GPIOA                          0x00000000u
+#define EXTI_GPIOB                          0x00000001u
+#define EXTI_GPIOC                          0x00000002u
+#if defined (GPIOD)
+#define EXTI_GPIOD                          0x00000003u
+#endif /* GPIOD*/
+#if defined (GPIOE)
+#define EXTI_GPIOE                          0x00000004u
+#endif /* GPIOE*/
+#if defined (GPIOH)
+#define EXTI_GPIOH                          0x00000007u
+#endif /* GPIOH*/
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup EXTI_Exported_Macros EXTI Exported Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private constants --------------------------------------------------------*/
+/** @defgroup EXTI_Private_Constants EXTI Private Constants
+  * @{
+  */
+/**
+  * @brief  EXTI Line property definition
+  */
+#define EXTI_PROPERTY_SHIFT                  24u
+#define EXTI_DIRECT                         (0x01uL << EXTI_PROPERTY_SHIFT)
+#define EXTI_CONFIG                         (0x02uL << EXTI_PROPERTY_SHIFT)
+#define EXTI_GPIO                           ((0x04uL << EXTI_PROPERTY_SHIFT) | EXTI_CONFIG)
+#define EXTI_RESERVED                       (0x08uL << EXTI_PROPERTY_SHIFT)
+#define EXTI_PROPERTY_MASK                  (EXTI_DIRECT | EXTI_CONFIG | EXTI_GPIO)
+
+/**
+  * @brief  EXTI bit usage
+  */
+#define EXTI_PIN_MASK                       0x0000001Fu
+
+/**
+  * @brief  EXTI Mask for interrupt & event mode
+  */
+#define EXTI_MODE_MASK                      (EXTI_MODE_EVENT | EXTI_MODE_INTERRUPT)
+
+/**
+  * @brief  EXTI Mask for trigger possibilities
+  */
+#define EXTI_TRIGGER_MASK                   (EXTI_TRIGGER_RISING | EXTI_TRIGGER_FALLING)
+
+/**
+  * @brief  EXTI Line number
+  */
+#define EXTI_LINE_NB                        30u
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup EXTI_Private_Macros EXTI Private Macros
+  * @{
+  */
+#define IS_EXTI_LINE(__EXTI_LINE__)          ((((__EXTI_LINE__) & ~(EXTI_PROPERTY_MASK | EXTI_PIN_MASK)) == 0x00u) && \
+                                             ((((__EXTI_LINE__) & EXTI_PROPERTY_MASK) == EXTI_CONFIG)              || \
+                                              (((__EXTI_LINE__) & EXTI_PROPERTY_MASK) == EXTI_GPIO))               && \
+                                              (((__EXTI_LINE__) & EXTI_PIN_MASK) < EXTI_LINE_NB))
+
+#define IS_EXTI_MODE(__EXTI_LINE__)          ((((__EXTI_LINE__) & EXTI_MODE_MASK) != 0x00u) && \
+                                              (((__EXTI_LINE__) & ~EXTI_MODE_MASK) == 0x00u))
+
+#define IS_EXTI_TRIGGER(__EXTI_LINE__)       (((__EXTI_LINE__)  & ~EXTI_TRIGGER_MASK) == 0x00u)
+
+#define IS_EXTI_PENDING_EDGE(__EXTI_LINE__)  ((__EXTI_LINE__) == EXTI_TRIGGER_RISING_FALLING)
+
+#define IS_EXTI_CONFIG_LINE(__EXTI_LINE__)   (((__EXTI_LINE__) & EXTI_CONFIG) != 0x00u)
+
+#if !defined (GPIOH)
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC))
+#elif !defined (GPIOD)
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC) || \
+                                         ((__PORT__) == EXTI_GPIOH))
+#elif !defined (GPIOE)
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC) || \
+                                         ((__PORT__) == EXTI_GPIOD) || \
+                                         ((__PORT__) == EXTI_GPIOH))
+#else
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC) || \
+                                         ((__PORT__) == EXTI_GPIOD) || \
+                                         ((__PORT__) == EXTI_GPIOE) || \
+                                         ((__PORT__) == EXTI_GPIOH))
+#endif /* GPIOH */
+
+#define IS_EXTI_GPIO_PIN(__PIN__)       ((__PIN__) < 16u)
+/**
+  * @}
+  */
+
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup EXTI_Exported_Functions EXTI Exported Functions
+  * @brief    EXTI Exported Functions
+  * @{
+  */
+
+/** @defgroup EXTI_Exported_Functions_Group1 Configuration functions
+  * @brief    Configuration functions
+  * @{
+  */
+/* Configuration functions ****************************************************/
+HAL_StatusTypeDef HAL_EXTI_SetConfigLine(EXTI_HandleTypeDef *hexti, EXTI_ConfigTypeDef *pExtiConfig);
+HAL_StatusTypeDef HAL_EXTI_GetConfigLine(EXTI_HandleTypeDef *hexti, EXTI_ConfigTypeDef *pExtiConfig);
+HAL_StatusTypeDef HAL_EXTI_ClearConfigLine(EXTI_HandleTypeDef *hexti);
+HAL_StatusTypeDef HAL_EXTI_RegisterCallback(EXTI_HandleTypeDef *hexti, EXTI_CallbackIDTypeDef CallbackID, void (*pPendingCbfn)(void));
+HAL_StatusTypeDef HAL_EXTI_GetHandle(EXTI_HandleTypeDef *hexti, uint32_t ExtiLine);
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Exported_Functions_Group2 IO operation functions
+  * @brief    IO operation functions
+  * @{
+  */
+/* IO operation functions *****************************************************/
+void              HAL_EXTI_IRQHandler(EXTI_HandleTypeDef *hexti);
+uint32_t          HAL_EXTI_GetPending(EXTI_HandleTypeDef *hexti, uint32_t Edge);
+void              HAL_EXTI_ClearPending(EXTI_HandleTypeDef *hexti, uint32_t Edge);
+void              HAL_EXTI_GenerateSWI(EXTI_HandleTypeDef *hexti);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32L0xx_HAL_EXTI_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_flash.h

@@ -0,0 +1,378 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_flash.h
+  * @author  MCD Application Team
+  * @brief   Header file of Flash HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_FLASH_H
+#define __STM32L0xx_HAL_FLASH_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup FLASH
+  * @{
+  */
+
+/** @addtogroup FLASH_Private_Constants
+  * @{
+  */
+#define FLASH_TIMEOUT_VALUE      (50000U) /* 50 s */
+#define FLASH_SIZE_DATA_REGISTER FLASHSIZE_BASE
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Private_Macros
+  * @{
+  */
+
+#define IS_FLASH_TYPEPROGRAM(_VALUE_)   ((_VALUE_) == FLASH_TYPEPROGRAM_WORD)
+
+#define IS_FLASH_LATENCY(__LATENCY__) (((__LATENCY__) == FLASH_LATENCY_0) || \
+                                       ((__LATENCY__) == FLASH_LATENCY_1))
+
+/**
+  * @}
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup FLASH_Exported_Types FLASH Exported Types
+  * @{
+  */
+
+/**
+  * @brief  FLASH Procedure structure definition
+  */
+typedef enum
+{
+  FLASH_PROC_NONE              = 0,
+  FLASH_PROC_PAGEERASE         = 1,
+  FLASH_PROC_PROGRAM           = 2,
+} FLASH_ProcedureTypeDef;
+
+/**
+  * @brief  FLASH handle Structure definition
+  */
+typedef struct
+{
+  __IO FLASH_ProcedureTypeDef ProcedureOnGoing; /*!< Internal variable to indicate which procedure is ongoing or not in IT context */
+
+  __IO uint32_t               NbPagesToErase;   /*!< Internal variable to save the remaining sectors to erase in IT context*/
+
+  __IO uint32_t               Address;          /*!< Internal variable to save address selected for program or erase */
+
+  __IO uint32_t               Page;             /*!< Internal variable to define the current page which is erasing */
+
+  HAL_LockTypeDef             Lock;             /*!< FLASH locking object                */
+
+  __IO uint32_t               ErrorCode;        /*!< FLASH error code
+                                                     This parameter can be a value of @ref FLASH_Error_Codes  */
+} FLASH_ProcessTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup FLASH_Exported_Constants FLASH Exported Constants
+  * @{
+  */
+
+/** @defgroup FLASH_Error_Codes FLASH Error Codes
+  * @{
+  */
+
+#define HAL_FLASH_ERROR_NONE      0x00U  /*!< No error */
+#define HAL_FLASH_ERROR_PGA       0x01U  /*!< Programming alignment error */
+#define HAL_FLASH_ERROR_WRP       0x02U  /*!< Write protection error */
+#define HAL_FLASH_ERROR_OPTV      0x04U  /*!< Option validity error */
+#define HAL_FLASH_ERROR_SIZE      0x08U  /*!<  */
+#define HAL_FLASH_ERROR_RD        0x10U  /*!< Read protected error */
+#define HAL_FLASH_ERROR_FWWERR    0x20U  /*!< FLASH Write or Erase operation aborted */
+#define HAL_FLASH_ERROR_NOTZERO   0x40U  /*!< FLASH Write operation is done in a not-erased region */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Page_Size FLASH size information
+  * @{
+  */
+
+#define FLASH_SIZE                (uint32_t)((*((uint32_t *)FLASHSIZE_BASE)&0xFFFF) * 1024U)
+#define FLASH_PAGE_SIZE           (128U)  /*!< FLASH Page Size in bytes */
+
+#define FLASH_END                 (FLASH_BASE + FLASH_SIZE - 1)    /*!< FLASH end address in the alias region */
+
+#if defined (STM32L071xx) || defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+#define FLASH_BANK2_BASE          (FLASH_BASE + (FLASH_SIZE >> 1)) /*!< FLASH BANK2 base address in the alias region */
+#define FLASH_BANK1_END           (FLASH_BANK2_BASE - 1)           /*!< Program end FLASH BANK1 address */
+#define FLASH_BANK2_END           (FLASH_END)                      /*!< Program end FLASH BANK2 address */
+#endif
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Type_Program FLASH Type Program
+  * @{
+  */
+#define FLASH_TYPEPROGRAM_WORD       (0x02U)  /*!<Program a word (32-bit) at a specified address.*/
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Latency FLASH Latency
+  * @{
+  */
+#define FLASH_LATENCY_0            (0x00000000U)    /*!< FLASH Zero Latency cycle */
+#define FLASH_LATENCY_1            FLASH_ACR_LATENCY         /*!< FLASH One Latency cycle */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Interrupts FLASH Interrupts
+  * @{
+  */
+
+#define FLASH_IT_EOP               FLASH_PECR_EOPIE  /*!< End of programming interrupt source */
+#define FLASH_IT_ERR               FLASH_PECR_ERRIE  /*!< Error interrupt source */
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Flags FLASH Flags
+  * @{
+  */
+
+#define FLASH_FLAG_BSY             FLASH_SR_BSY        /*!< FLASH Busy flag */
+#define FLASH_FLAG_EOP             FLASH_SR_EOP        /*!< FLASH End of Programming flag */
+#define FLASH_FLAG_ENDHV           FLASH_SR_HVOFF      /*!< FLASH End of High Voltage flag */
+#define FLASH_FLAG_READY           FLASH_SR_READY      /*!< FLASH Ready flag after low power mode */
+#define FLASH_FLAG_WRPERR          FLASH_SR_WRPERR     /*!< FLASH Write protected error flag */
+#define FLASH_FLAG_PGAERR          FLASH_SR_PGAERR     /*!< FLASH Programming Alignment error flag */
+#define FLASH_FLAG_SIZERR          FLASH_SR_SIZERR     /*!< FLASH Size error flag  */
+#define FLASH_FLAG_OPTVERR         FLASH_SR_OPTVERR    /*!< FLASH Option Validity error flag  */
+#define FLASH_FLAG_RDERR           FLASH_SR_RDERR      /*!< FLASH Read protected error flag */
+#define FLASH_FLAG_FWWERR          FLASH_SR_FWWERR     /*!< FLASH Write or Errase operation aborted */
+#define FLASH_FLAG_NOTZEROERR      FLASH_SR_NOTZEROERR /*!< FLASH Read protected error flag */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Keys FLASH Keys
+  * @{
+  */
+
+#define FLASH_PDKEY1               (0x04152637U) /*!< Flash power down key1 */
+#define FLASH_PDKEY2               (0xFAFBFCFDU) /*!< Flash power down key2: used with FLASH_PDKEY1
+                                                    to unlock the RUN_PD bit in FLASH_ACR */
+
+#define FLASH_PEKEY1               (0x89ABCDEFU) /*!< Flash program erase key1 */
+#define FLASH_PEKEY2               (0x02030405U) /*!< Flash program erase key: used with FLASH_PEKEY2
+                                                     to unlock the write access to the FLASH_PECR register and
+                                                     data EEPROM */
+
+#define FLASH_PRGKEY1              (0x8C9DAEBFU) /*!< Flash program memory key1 */
+#define FLASH_PRGKEY2              (0x13141516U) /*!< Flash program memory key2: used with FLASH_PRGKEY2
+                                                     to unlock the program memory */
+
+#define FLASH_OPTKEY1              (0xFBEAD9C8U) /*!< Flash option key1 */
+#define FLASH_OPTKEY2              (0x24252627U) /*!< Flash option key2: used with FLASH_OPTKEY1 to
+                                                              unlock the write access to the option byte block */
+/**
+  * @}
+  */
+
+/* CMSIS_Legacy */
+
+#if defined ( __ICCARM__ )
+#define InterruptType_ACTLR_DISMCYCINT_Msk         IntType_ACTLR_DISMCYCINT_Msk
+#endif
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+
+/** @defgroup FLASH_Exported_Macros FLASH Exported Macros
+ *  @brief macros to control FLASH features
+ *  @{
+ */
+
+
+/** @defgroup FLASH_Interrupt FLASH Interrupts
+ *  @brief macros to handle FLASH interrupts
+ * @{
+ */
+
+/**
+  * @brief  Enable the specified FLASH interrupt.
+  * @param  __INTERRUPT__  FLASH interrupt
+  *         This parameter can be any combination of the following values:
+  *     @arg @ref FLASH_IT_EOP End of FLASH Operation Interrupt
+  *     @arg @ref FLASH_IT_ERR Error Interrupt
+  * @retval none
+  */
+#define __HAL_FLASH_ENABLE_IT(__INTERRUPT__)  SET_BIT((FLASH->PECR), (__INTERRUPT__))
+
+/**
+  * @brief  Disable the specified FLASH interrupt.
+  * @param  __INTERRUPT__  FLASH interrupt
+  *         This parameter can be any combination of the following values:
+  *     @arg @ref FLASH_IT_EOP End of FLASH Operation Interrupt
+  *     @arg @ref FLASH_IT_ERR Error Interrupt
+  * @retval none
+  */
+#define __HAL_FLASH_DISABLE_IT(__INTERRUPT__)  CLEAR_BIT((FLASH->PECR), (uint32_t)(__INTERRUPT__))
+
+/**
+  * @brief  Get the specified FLASH flag status.
+  * @param  __FLAG__ specifies the FLASH flag to check.
+  *          This parameter can be one of the following values:
+  *            @arg @ref FLASH_FLAG_BSY         FLASH Busy flag
+  *            @arg @ref FLASH_FLAG_EOP         FLASH End of Operation flag
+  *            @arg @ref FLASH_FLAG_ENDHV       FLASH End of High Voltage flag
+  *            @arg @ref FLASH_FLAG_READY       FLASH Ready flag after low power mode
+  *            @arg @ref FLASH_FLAG_PGAERR      FLASH Programming Alignment error flag
+  *            @arg @ref FLASH_FLAG_SIZERR      FLASH Size error flag
+  *            @arg @ref FLASH_FLAG_OPTVERR     FLASH Option validity error flag (not valid with STM32L031xx/STM32L041xx)
+  *            @arg @ref FLASH_FLAG_RDERR       FLASH Read protected error flag
+  *            @arg @ref FLASH_FLAG_WRPERR      FLASH Write protected error flag
+  *            @arg @ref FLASH_FLAG_FWWERR      FLASH Fetch While Write Error flag
+  *            @arg @ref FLASH_FLAG_NOTZEROERR  Not Zero area error flag
+  * @retval The new state of __FLAG__ (SET or RESET).
+  */
+#define __HAL_FLASH_GET_FLAG(__FLAG__)   (((FLASH->SR) & (__FLAG__)) == (__FLAG__))
+
+/**
+  * @brief  Clear the specified FLASH flag.
+  * @param  __FLAG__ specifies the FLASH flags to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg @ref FLASH_FLAG_EOP         FLASH End of Operation flag
+  *            @arg @ref FLASH_FLAG_PGAERR      FLASH Programming Alignment error flag
+  *            @arg @ref FLASH_FLAG_SIZERR      FLASH Size error flag
+  *            @arg @ref FLASH_FLAG_OPTVERR     FLASH Option validity error flag (not valid with STM32L031xx/STM32L041xx)
+  *            @arg @ref FLASH_FLAG_RDERR       FLASH Read protected error flag
+  *            @arg @ref FLASH_FLAG_WRPERR      FLASH Write protected error flag
+  *            @arg @ref FLASH_FLAG_FWWERR      FLASH Fetch While Write Error flag
+  *            @arg @ref FLASH_FLAG_NOTZEROERR  Not Zero area error flag
+  * @retval none
+  */
+#define __HAL_FLASH_CLEAR_FLAG(__FLAG__)   ((FLASH->SR) = (__FLAG__))
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Include FLASH HAL Extended module */
+#include "stm32l0xx_hal_flash_ex.h"
+#include "stm32l0xx_hal_flash_ramfunc.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup FLASH_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup FLASH_Exported_Functions_Group1
+  * @{
+  */
+/* IO operation functions *****************************************************/
+HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint32_t Data);
+HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint32_t Data);
+
+/* FLASH IRQ handler function */
+void       HAL_FLASH_IRQHandler(void);
+/* Callbacks in non blocking modes */
+void       HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue);
+void       HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue);
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Exported_Functions_Group2
+  * @{
+  */
+/* Peripheral Control functions ***********************************************/
+HAL_StatusTypeDef HAL_FLASH_Unlock(void);
+HAL_StatusTypeDef HAL_FLASH_Lock(void);
+HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void);
+HAL_StatusTypeDef HAL_FLASH_OB_Lock(void);
+HAL_StatusTypeDef HAL_FLASH_OB_Launch(void);
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral State and Error functions ***************************************/
+uint32_t HAL_FLASH_GetError(void);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private function -------------------------------------------------*/
+/** @addtogroup FLASH_Private_Functions
+ * @{
+ */
+HAL_StatusTypeDef       FLASH_WaitForLastOperation(uint32_t Timeout);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L0xx_HAL_FLASH_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_flash_ex.h

@@ -0,0 +1,811 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_flash_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of Flash HAL Extended module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_FLASH_EX_H
+#define __STM32L0xx_HAL_FLASH_EX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup FLASHEx
+  * @{
+  */
+
+/** @addtogroup FLASHEx_Private_Constants
+  * @{
+  */
+#define FLASH_SIZE_DATA_REGISTER   FLASHSIZE_BASE
+
+#define FLASH_NBPAGES_MAX (FLASH_SIZE / FLASH_PAGE_SIZE)
+
+#define WRP_MASK_LOW                 (0x0000FFFFU)
+#define WRP_MASK_HIGH                (0xFFFF0000U)
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASHEx_Private_Macros
+  * @{
+  */
+
+#define IS_FLASH_TYPEERASE(__VALUE__)   (((__VALUE__) == FLASH_TYPEERASE_PAGES))
+
+#define IS_OPTIONBYTE(__VALUE__) (((__VALUE__) <= (OPTIONBYTE_WRP  | OPTIONBYTE_RDP | \
+                                                  OPTIONBYTE_USER | OPTIONBYTE_BOR | OPTIONBYTE_BOOT_BIT1)))
+
+#define IS_WRPSTATE(__VALUE__)          (((__VALUE__) == OB_WRPSTATE_DISABLE) || \
+                                         ((__VALUE__) == OB_WRPSTATE_ENABLE))
+
+#define IS_OB_WRP(__PAGE__)             (((__PAGE__) != 0x0000000U))
+
+#define IS_OB_RDP(__LEVEL__)            (((__LEVEL__) == OB_RDP_LEVEL_0) ||\
+                                         ((__LEVEL__) == OB_RDP_LEVEL_1) ||\
+                                         ((__LEVEL__) == OB_RDP_LEVEL_2))
+
+#define IS_OB_BOR_LEVEL(__LEVEL__)      (((__LEVEL__) == OB_BOR_OFF)     || \
+                                         ((__LEVEL__) == OB_BOR_LEVEL1)  || \
+                                         ((__LEVEL__) == OB_BOR_LEVEL2)  || \
+                                         ((__LEVEL__) == OB_BOR_LEVEL3)  || \
+                                         ((__LEVEL__) == OB_BOR_LEVEL4)  || \
+                                         ((__LEVEL__) == OB_BOR_LEVEL5))
+
+#define IS_OB_IWDG_SOURCE(__SOURCE__)   (((__SOURCE__) == OB_IWDG_SW) || ((__SOURCE__) == OB_IWDG_HW))
+
+#define IS_OB_STOP_SOURCE(__SOURCE__)   (((__SOURCE__) == OB_STOP_NORST) || ((__SOURCE__) == OB_STOP_RST))
+
+#define IS_OB_STDBY_SOURCE(__SOURCE__)  (((__SOURCE__) == OB_STDBY_NORST) || ((__SOURCE__) == OB_STDBY_RST))
+
+#if defined(FLASH_OPTR_WPRMOD) && defined(FLASH_OPTR_BFB2)
+
+#define IS_OBEX(__VALUE__)              (((__VALUE__) <= (OPTIONBYTE_PCROP | OPTIONBYTE_BOOTCONFIG)) && ((__VALUE__) != 0U))
+
+#elif defined(FLASH_OPTR_WPRMOD) && !defined(FLASH_OPTR_BFB2)
+
+#define IS_OBEX(__VALUE__)              ((__VALUE__) == OPTIONBYTE_PCROP)
+
+#elif !defined(FLASH_OPTR_WPRMOD) && defined(FLASH_OPTR_BFB2)
+
+#define IS_OBEX(__VALUE__)              ((__VALUE__) == OPTIONBYTE_BOOTCONFIG)
+
+#endif /* FLASH_OPTR_WPRMOD && FLASH_OPTR_BFB2 */
+
+#if defined(FLASH_OPTR_WPRMOD)
+
+#define IS_PCROPSTATE(__VALUE__)        (((__VALUE__) == OB_PCROP_STATE_DISABLE) || \
+                                         ((__VALUE__) == OB_PCROP_STATE_ENABLE))
+
+#define IS_OB_PCROP(__PAGE__)           (((__PAGE__) != 0x0000000U))
+#endif /* FLASH_OPTR_WPRMOD */
+
+#if defined(FLASH_OPTR_BFB2)
+
+#define IS_OB_BOOT_BANK(__BANK__)     (((__BANK__) == OB_BOOT_BANK2) || ((__BANK__) == OB_BOOT_BANK1))
+
+#endif /* FLASH_OPTR_BFB2 */
+
+#define IS_OB_BOOT1(__BOOT_BIT1__)  (((__BOOT_BIT1__) == OB_BOOT_BIT1_RESET) || ((__BOOT_BIT1__) == OB_BOOT_BIT1_SET))
+#define IS_TYPEPROGRAMDATA(__VALUE__)   (((__VALUE__) == FLASH_TYPEPROGRAMDATA_BYTE)     || \
+                                         ((__VALUE__) == FLASH_TYPEPROGRAMDATA_HALFWORD) || \
+                                         ((__VALUE__) == FLASH_TYPEPROGRAMDATA_WORD))
+
+
+/** @defgroup FLASHEx_Address FLASHEx Address
+  * @{
+  */
+
+#if defined (STM32L071xx) || defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+
+#define IS_FLASH_DATA_ADDRESS(__ADDRESS__)          (((__ADDRESS__) >= DATA_EEPROM_BASE) && ((__ADDRESS__) <= DATA_EEPROM_BANK2_END))
+#define IS_FLASH_DATA_BANK1_ADDRESS(__ADDRESS__)    (((__ADDRESS__) >= DATA_EEPROM_BASE) && ((__ADDRESS__) <= DATA_EEPROM_BANK1_END))
+#define IS_FLASH_DATA_BANK2_ADDRESS(__ADDRESS__)    (((__ADDRESS__) >= DATA_EEPROM_BANK2_BASE) && ((__ADDRESS__) <= DATA_EEPROM_BANK2_END))
+#define IS_FLASH_PROGRAM_ADDRESS(__ADDRESS__)       (((__ADDRESS__) >= FLASH_BASE)       && ((__ADDRESS__) <  (FLASH_BASE + FLASH_SIZE)))
+#define IS_FLASH_PROGRAM_BANK1_ADDRESS(__ADDRESS__) (((__ADDRESS__) >= FLASH_BASE)       && ((__ADDRESS__) <  (FLASH_BASE + (FLASH_SIZE >> 1))))
+#define IS_FLASH_PROGRAM_BANK2_ADDRESS(__ADDRESS__) (((__ADDRESS__) >= FLASH_BANK2_BASE) && ((__ADDRESS__) <  (FLASH_BASE + FLASH_SIZE)))
+#else
+#define IS_FLASH_DATA_ADDRESS(__ADDRESS__)          (((__ADDRESS__) >= DATA_EEPROM_BASE) && ((__ADDRESS__) <= DATA_EEPROM_END))
+#define IS_FLASH_PROGRAM_ADDRESS(__ADDRESS__)       (((__ADDRESS__) >= FLASH_BASE)       && ((__ADDRESS__) <  (FLASH_BASE + FLASH_SIZE)))
+#endif
+
+#define IS_NBPAGES(__PAGES__) (((__PAGES__) >= 1) && ((__PAGES__) <= FLASH_NBPAGES_MAX))
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup FLASHEx_Exported_Types FLASHEx Exported Types
+  * @{
+  */
+
+/**
+  * @brief  FLASH Erase structure definition
+  */
+typedef struct
+{
+  uint32_t TypeErase;   /*!< TypeErase: Page Erase only.
+                             This parameter can be a value of @ref FLASHEx_Type_Erase */
+
+  uint32_t PageAddress; /*!< PageAddress: Initial FLASH address to be erased
+                             This parameter must be a value belonging to FLASH Programm address (depending on the devices)  */
+
+  uint32_t NbPages;     /*!< NbPages: Number of pages to be erased.
+                             This parameter must be a value between 1 and (max number of pages - value of Initial page)*/
+
+} FLASH_EraseInitTypeDef;
+
+/**
+  * @brief  FLASH Option Bytes PROGRAM structure definition
+  */
+typedef struct
+{
+  uint32_t  OptionType;       /*!< OptionType: Option byte to be configured.
+                                   This parameter can be a value of @ref FLASHEx_Option_Type */
+
+  uint32_t  WRPState;         /*!< WRPState: Write protection activation or deactivation.
+                                   This parameter can be a value of @ref FLASHEx_WRP_State */
+
+  uint32_t WRPSector;         /*!< WRPSector: This bitfield specifies the sector (s) which are write protected.
+                                   This parameter can be a combination of @ref FLASHEx_Option_Bytes_Write_Protection */
+
+#if defined(STM32L071xx) || defined(STM32L072xx) || defined(STM32L073xx) || defined(STM32L081xx) || defined(STM32L082xx) || defined(STM32L083xx)
+  uint32_t WRPSector2;        /*!< WRPSector2 : This bitfield specifies the sector(s) upper Sector31 which are write protected.
+                                   This parameter can be a combination of @ref FLASHEx_Option_Bytes_Write_Protection2 */
+#endif
+
+  uint8_t   RDPLevel;         /*!< RDPLevel: Set the read protection level.
+                                   This parameter can be a value of @ref FLASHEx_Option_Bytes_Read_Protection */
+
+  uint8_t   BORLevel;         /*!< BORLevel: Set the BOR Level.
+                                   This parameter can be a value of @ref FLASHEx_Option_Bytes_BOR_Level */
+
+  uint8_t   USERConfig;       /*!< USERConfig: Program the FLASH User Option Byte: IWDG_SW / RST_STOP / RST_STDBY.
+                                   This parameter can be a combination of @ref FLASHEx_Option_Bytes_IWatchdog,
+                                   @ref FLASHEx_Option_Bytes_nRST_STOP and @ref FLASHEx_Option_Bytes_nRST_STDBY*/
+
+  uint8_t BOOTBit1Config;     /*!< BOOT1Config: Together with input pad Boot0, this bit selects the boot source, flash, ram or system memory
+                                   This parameter can be a value of @ref FLASHEx_Option_Bytes_BOOTBit1 */
+} FLASH_OBProgramInitTypeDef;
+
+#if defined(FLASH_OPTR_WPRMOD) || defined(FLASH_OPTR_BFB2)
+/**
+  * @brief  FLASH Advanced Option Bytes Program structure definition
+  */
+typedef struct
+{
+  uint32_t OptionType;          /*!< OptionType: Option byte to be configured for extension .
+                                     This parameter can be a value of @ref FLASHEx_OptionAdv_Type */
+
+#if defined(FLASH_OPTR_WPRMOD)
+  uint32_t PCROPState;          /*!< PCROPState: PCROP activation or deactivation.
+                                     This parameter can be a value of @ref FLASHEx_PCROP_State */
+
+  uint32_t PCROPSector;        /*!< PCROPSector : This bitfield specifies the sector(s) which are read/write protected.
+                                    This parameter can be a combination of @ref FLASHEx_Option_Bytes_PC_ReadWrite_Protection */
+
+#if defined (STM32L071xx) || defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+  uint32_t PCROPSector2;       /*!< PCROPSector : This bitfield specifies the sector(s) upper Sector31 which are read/write protected.
+                                    This parameter can be a combination of @ref FLASHEx_Option_Bytes_PC_ReadWrite_Protection2 */
+#endif /* STM32L071xx || STM32L072xx || STM32L073xx || STM32L081xx || STM32L082xx || STM32L083xx */
+#endif /* FLASH_OPTR_WPRMOD */
+
+#if defined(FLASH_OPTR_BFB2)
+  uint16_t BootConfig;          /*!< BootConfig: specifies Option bytes for boot config
+                                     This parameter can be a value of @ref FLASHEx_Option_Bytes_BOOT */
+#endif /* FLASH_OPTR_BFB2*/
+} FLASH_AdvOBProgramInitTypeDef;
+
+/**
+  * @}
+  */
+#endif /* FLASH_OPTR_WPRMOD || FLASH_OPTR_BFB2 */
+
+/* Exported constants --------------------------------------------------------*/
+
+
+/** @defgroup FLASHEx_Exported_Constants FLASHEx Exported Constants
+  * @{
+  */
+
+/** @defgroup FLASHEx_Type_Erase FLASHEx_Type_Erase
+  * @{
+  */
+#define FLASH_TYPEERASE_PAGES           (0x00U)  /*!<Page erase only*/
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Option_Type FLASHEx Option Type
+  * @{
+  */
+#define OPTIONBYTE_WRP            (0x01U)  /*!<WRP option byte configuration*/
+#define OPTIONBYTE_RDP            (0x02U)  /*!<RDP option byte configuration*/
+#define OPTIONBYTE_USER           (0x04U)  /*!<USER option byte configuration*/
+#define OPTIONBYTE_BOR            (0x08U)  /*!<BOR option byte configuration*/
+#define OPTIONBYTE_BOOT_BIT1      (0x10U)  /*!< BOOT PIN1 option byte configuration*/
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_WRP_State FLASHEx WRP State
+  * @{
+  */
+#define OB_WRPSTATE_DISABLE        (0x00U)  /*!<Disable the write protection of the desired sectors*/
+#define OB_WRPSTATE_ENABLE         (0x01U)  /*!<Enable the write protection of the desired sectors*/
+
+/**
+  * @}
+  */
+
+#if defined (STM32L011xx) || defined (STM32L021xx) || defined (STM32L031xx) || defined (STM32L041xx)
+/** @defgroup FLASHEx_Option_Bytes_Write_Protection FLASH Option Bytes Write Protection
+  * @{
+  */
+#define OB_WRP_Pages0to31          (0x00000001U) /* Write protection of Sector0 */
+#define OB_WRP_Pages32to63         (0x00000002U) /* Write protection of Sector1 */
+#define OB_WRP_Pages64to95         (0x00000004U) /* Write protection of Sector2 */
+#define OB_WRP_Pages96to127        (0x00000008U) /* Write protection of Sector3 */
+#define OB_WRP_Pages128to159       (0x00000010U) /* Write protection of Sector4 */
+#define OB_WRP_Pages160to191       (0x00000020U) /* Write protection of Sector5 */
+#define OB_WRP_Pages192to223       (0x00000040U) /* Write protection of Sector6 */
+#define OB_WRP_Pages224to255       (0x00000080U) /* Write protection of Sector7 */
+#define OB_WRP_AllPages            (0x000000FFU) /*!< Write protection of all Sectors */
+/**
+  * @}
+  */
+#elif defined (STM32L051xx) || defined (STM32L052xx) || defined (STM32L053xx) || defined (STM32L062xx) || defined (STM32L063xx)
+/** @defgroup FLASHEx_Option_Bytes_Write_Protection FLASH Option Bytes Write Protection
+  * @{
+  */
+#define OB_WRP_Pages0to31          (0x00000001U) /* Write protection of Sector0 */
+#define OB_WRP_Pages32to63         (0x00000002U) /* Write protection of Sector1 */
+#define OB_WRP_Pages64to95         (0x00000004U) /* Write protection of Sector2 */
+#define OB_WRP_Pages96to127        (0x00000008U) /* Write protection of Sector3 */
+#define OB_WRP_Pages128to159       (0x00000010U) /* Write protection of Sector4 */
+#define OB_WRP_Pages160to191       (0x00000020U) /* Write protection of Sector5 */
+#define OB_WRP_Pages192to223       (0x00000040U) /* Write protection of Sector6 */
+#define OB_WRP_Pages224to255       (0x00000080U) /* Write protection of Sector7 */
+#define OB_WRP_Pages256to287       (0x00000100U) /* Write protection of Sector8 */
+#define OB_WRP_Pages288to319       (0x00000200U) /* Write protection of Sector9 */
+#define OB_WRP_Pages320to351       (0x00000400U) /* Write protection of Sector10 */
+#define OB_WRP_Pages352to383       (0x00000800U) /* Write protection of Sector11 */
+#define OB_WRP_Pages384to415       (0x00001000U) /* Write protection of Sector12 */
+#define OB_WRP_Pages416to447       (0x00002000U) /* Write protection of Sector13 */
+#define OB_WRP_Pages448to479       (0x00004000U) /* Write protection of Sector14 */
+#define OB_WRP_Pages480to511       (0x00008000U) /* Write protection of Sector15 */
+#define OB_WRP_AllPages            (0x0000FFFFU) /*!< Write protection of all Sectors */
+/**
+  * @}
+  */
+
+#elif defined (STM32L071xx) || defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+/** @defgroup FLASHEx_Option_Bytes_Write_Protection FLASH Option Bytes Write ProtectionP
+  * @{
+  */
+#define OB_WRP_Pages0to31          (0x00000001U) /* Write protection of Sector0 */
+#define OB_WRP_Pages32to63         (0x00000002U) /* Write protection of Sector1 */
+#define OB_WRP_Pages64to95         (0x00000004U) /* Write protection of Sector2 */
+#define OB_WRP_Pages96to127        (0x00000008U) /* Write protection of Sector3 */
+#define OB_WRP_Pages128to159       (0x00000010U) /* Write protection of Sector4 */
+#define OB_WRP_Pages160to191       (0x00000020U) /* Write protection of Sector5 */
+#define OB_WRP_Pages192to223       (0x00000040U) /* Write protection of Sector6 */
+#define OB_WRP_Pages224to255       (0x00000080U) /* Write protection of Sector7 */
+#define OB_WRP_Pages256to287       (0x00000100U) /* Write protection of Sector8 */
+#define OB_WRP_Pages288to319       (0x00000200U) /* Write protection of Sector9 */
+#define OB_WRP_Pages320to351       (0x00000400U) /* Write protection of Sector10 */
+#define OB_WRP_Pages352to383       (0x00000800U) /* Write protection of Sector11 */
+#define OB_WRP_Pages384to415       (0x00001000U) /* Write protection of Sector12 */
+#define OB_WRP_Pages416to447       (0x00002000U) /* Write protection of Sector13 */
+#define OB_WRP_Pages448to479       (0x00004000U) /* Write protection of Sector14 */
+#define OB_WRP_Pages480to511       (0x00008000U) /* Write protection of Sector15 */
+#define OB_WRP_Pages512to543       (0x00010000U) /* Write protection of Sector16 */
+#define OB_WRP_Pages544to575       (0x00020000U) /* Write protection of Sector17 */
+#define OB_WRP_Pages576to607       (0x00040000U) /* Write protection of Sector18 */
+#define OB_WRP_Pages608to639       (0x00080000U) /* Write protection of Sector19 */
+#define OB_WRP_Pages640to671       (0x00100000U) /* Write protection of Sector20 */
+#define OB_WRP_Pages672to703       (0x00200000U) /* Write protection of Sector21 */
+#define OB_WRP_Pages704to735       (0x00400000U) /* Write protection of Sector22 */
+#define OB_WRP_Pages736to767       (0x00800000U) /* Write protection of Sector23 */
+#define OB_WRP_Pages768to799       (0x01000000U) /* Write protection of Sector24 */
+#define OB_WRP_Pages800to831       (0x02000000U) /* Write protection of Sector25 */
+#define OB_WRP_Pages832to863       (0x04000000U) /* Write protection of Sector26 */
+#define OB_WRP_Pages864to895       (0x08000000U) /* Write protection of Sector27 */
+#define OB_WRP_Pages896to927       (0x10000000U) /* Write protection of Sector28 */
+#define OB_WRP_Pages928to959       (0x20000000U) /* Write protection of Sector29 */
+#define OB_WRP_Pages960to991       (0x40000000U) /* Write protection of Sector30 */
+#define OB_WRP_Pages992to1023      (0x80000000U) /* Write protection of Sector31 */
+#define OB_WRP_AllPages            (0xFFFFFFFFU) /*!<Write  protection of all Sectors */
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Option_Bytes_Write_Protection2 FLASH Option Bytes Write Protection
+  * @{
+  */
+#define OB_WRP2_Pages1024to1055    (0x00000001U) /* Write protection of Sector32 */
+#define OB_WRP2_Pages1056to1087    (0x00000002U) /* Write protection of Sector33 */
+#define OB_WRP2_Pages1088to1119    (0x00000004U) /* Write protection of Sector34 */
+#define OB_WRP2_Pages1120to1151    (0x00000008U) /* Write protection of Sector35 */
+#define OB_WRP2_Pages1152to1183    (0x00000010U) /* Write protection of Sector36 */
+#define OB_WRP2_Pages1184to1215    (0x00000020U) /* Write protection of Sector37 */
+#define OB_WRP2_Pages1216to1247    (0x00000040U) /* Write protection of Sector38 */
+#define OB_WRP2_Pages1248to1279    (0x00000080U) /* Write protection of Sector39 */
+#define OB_WRP2_Pages1280to1311    (0x00000100U) /* Write protection of Sector40 */
+#define OB_WRP2_Pages1312to1343    (0x00000200U) /* Write protection of Sector41 */
+#define OB_WRP2_Pages1344to1375    (0x00000400U) /* Write protection of Sector42 */
+#define OB_WRP2_Pages1376to1407    (0x00000800U) /* Write protection of Sector43 */
+#define OB_WRP2_Pages1408to1439    (0x00001000U) /* Write protection of Sector44 */
+#define OB_WRP2_Pages1440to1471    (0x00002000U) /* Write protection of Sector45 */
+#define OB_WRP2_Pages1472to1503    (0x00004000U) /* Write protection of Sector46 */
+#define OB_WRP2_Pages1504to1535    (0x00008000U) /* Write protection of Sector47 */
+#define OB_WRP2_AllPages           (0x0000FFFFU) /*!< Write protection of all Sectors WRP2 */
+/**
+  * @}
+  */
+#endif /* STM32L071xx || STM32L072xx || (STM32L073xx) || (STM32L081xx) || (STM32L082xx) || (STM32L083xx) */
+
+/** @defgroup FLASHEx_Option_Bytes_Read_Protection FLASHEx Option Bytes Read Protection
+  * @{
+  */
+#define OB_RDP_LEVEL_0         ((uint8_t)0xAA)
+#define OB_RDP_LEVEL_1         ((uint8_t)0xBB)
+#define OB_RDP_LEVEL_2         ((uint8_t)0xCC) /* Warning: When enabling read protection level 2
+                                                it is no more possible to go back to level 1 or 0 */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Option_Bytes_BOR_Level FLASHEx Option Bytes BOR Level
+  * @{
+  */
+
+#define OB_BOR_OFF       ((uint8_t)0x00) /*!< BOR is disabled at power down, the reset is asserted when the VDD
+                                             power supply reaches the PDR(Power Down Reset) threshold (1.5V) */
+#define OB_BOR_LEVEL1    ((uint8_t)0x08) /*!< BOR Reset threshold levels for 1.7V - 1.8V VDD power supply    */
+#define OB_BOR_LEVEL2    ((uint8_t)0x09) /*!< BOR Reset threshold levels for 1.9V - 2.0V VDD power supply    */
+#define OB_BOR_LEVEL3    ((uint8_t)0x0A) /*!< BOR Reset threshold levels for 2.3V - 2.4V VDD power supply    */
+#define OB_BOR_LEVEL4    ((uint8_t)0x0B) /*!< BOR Reset threshold levels for 2.55V - 2.65V VDD power supply  */
+#define OB_BOR_LEVEL5    ((uint8_t)0x0C) /*!< BOR Reset threshold levels for 2.8V - 2.9V VDD power supply    */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Option_Bytes_IWatchdog FLASHEx Option Bytes IWatchdog
+  * @{
+  */
+
+#define OB_IWDG_SW                     ((uint8_t)0x10)  /*!< Software WDG selected */
+#define OB_IWDG_HW                     ((uint8_t)0x00)  /*!< Hardware WDG selected */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Option_Bytes_nRST_STOP FLASHEx Option Bytes nRST_STOP
+  * @{
+  */
+
+#define OB_STOP_NORST                  ((uint8_t)0x20) /*!< No reset generated when entering in STOP */
+#define OB_STOP_RST                    ((uint8_t)0x00) /*!< Reset generated when entering in STOP */
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Option_Bytes_nRST_STDBY FLASHEx Option Bytes nRST_STDBY
+  * @{
+  */
+
+#define OB_STDBY_NORST                 ((uint8_t)0x40) /*!< No reset generated when entering in STANDBY */
+#define OB_STDBY_RST                   ((uint8_t)0x00) /*!< Reset generated when entering in STANDBY */
+
+/**
+  * @}
+  */
+
+#if defined(FLASH_OPTR_WPRMOD)
+
+/** @defgroup FLASHEx_OptionAdv_Type FLASHEx Option Advanced Type
+  * @{
+  */
+
+#define OPTIONBYTE_PCROP        (0x01U)  /*!<PCROP option byte configuration*/
+
+/**
+  * @}
+  */
+
+#endif /* FLASH_OPTR_WPRMOD */
+
+#if defined(FLASH_OPTR_BFB2)
+
+/** @defgroup FLASHEx_OptionAdv_Type FLASHEx Option Advanced Type
+  * @{
+  */
+
+#define OPTIONBYTE_BOOTCONFIG   (0x02U)  /*!<BOOTConfig option byte configuration*/
+
+/**
+  * @}
+  */
+
+#endif /* FLASH_OPTR_BFB2 */
+
+#if defined(FLASH_OPTR_WPRMOD)
+
+/** @defgroup  FLASHEx_PCROP_State FLASHEx PCROP State
+  * @{
+  */
+#define OB_PCROP_STATE_DISABLE        (0x00U)  /*!<Disable PCROP for selected sectors */
+#define OB_PCROP_STATE_ENABLE         (0x01U)  /*!<Enable PCROP for selected sectors */
+
+/**
+  * @}
+  */
+
+/** @defgroup  FLASHEx_Selection_Protection_Mode FLASHEx Selection Protection Mode
+  * @{
+  */
+#define OB_PCROP_DESELECTED     ((uint16_t)0x0000)            /*!< Disabled PCROP, nWPRi bits used for Write Protection on sector i */
+#define OB_PCROP_SELECTED       ((uint16_t)FLASH_OPTR_WPRMOD)  /*!< Enable PCROP, nWPRi bits used for PCRoP Protection on sector i   */
+
+/**
+  * @}
+  */
+#endif /* FLASH_OPTR_WPRMOD */
+
+#if defined (STM32L011xx) || defined (STM32L021xx) ||  defined (STM32L031xx) || defined (STM32L041xx)
+/** @defgroup FLASHEx_Option_Bytes_PC_ReadWrite_Protection FLASHEx Option Bytes PC Read/Write Protection
+  * @{
+  */
+#define OB_PCROP_Pages0to31          (0x00000001U) /* PC Read/Write protection of Sector0 */
+#define OB_PCROP_Pages32to63         (0x00000002U) /* PC Read/Write protection of Sector1 */
+#define OB_PCROP_Pages64to95         (0x00000004U) /* PC Read/Write protection of Sector2 */
+#define OB_PCROP_Pages96to127        (0x00000008U) /* PC Read/Write protection of Sector3 */
+#define OB_PCROP_Pages128to159       (0x00000010U) /* PC Read/Write protection of Sector4 */
+#define OB_PCROP_Pages160to191       (0x00000020U) /* PC Read/Write protection of Sector5 */
+#define OB_PCROP_Pages192to223       (0x00000040U) /* PC Read/Write protection of Sector6 */
+#define OB_PCROP_Pages224to255       (0x00000080U) /* PC Read/Write protection of Sector7 */
+#define OB_PCROP_AllPages            (0x000000FFU) /*!< PC Read/Write protection of all Sectors */
+/**
+  * @}
+  */
+#elif defined (STM32L051xx) || defined (STM32L052xx) || defined (STM32L053xx) || defined (STM32L062xx) || defined (STM32L063xx)
+/** @defgroup FLASHEx_Option_Bytes_PC_ReadWrite_Protection FLASHEx Option Bytes PC Read/Write Protection
+  * @{
+  */
+#define OB_PCROP_Pages0to31          (0x00000001U) /* PC Read/Write protection of Sector0 */
+#define OB_PCROP_Pages32to63         (0x00000002U) /* PC Read/Write protection of Sector1 */
+#define OB_PCROP_Pages64to95         (0x00000004U) /* PC Read/Write protection of Sector2 */
+#define OB_PCROP_Pages96to127        (0x00000008U) /* PC Read/Write protection of Sector3 */
+#define OB_PCROP_Pages128to159       (0x00000010U) /* PC Read/Write protection of Sector4 */
+#define OB_PCROP_Pages160to191       (0x00000020U) /* PC Read/Write protection of Sector5 */
+#define OB_PCROP_Pages192to223       (0x00000040U) /* PC Read/Write protection of Sector6 */
+#define OB_PCROP_Pages224to255       (0x00000080U) /* PC Read/Write protection of Sector7 */
+#define OB_PCROP_Pages256to287       (0x00000100U) /* PC Read/Write protection of Sector8 */
+#define OB_PCROP_Pages288to319       (0x00000200U) /* PC Read/Write protection of Sector9 */
+#define OB_PCROP_Pages320to351       (0x00000400U) /* PC Read/Write protection of Sector10 */
+#define OB_PCROP_Pages352to383       (0x00000800U) /* PC Read/Write protection of Sector11 */
+#define OB_PCROP_Pages384to415       (0x00001000U) /* PC Read/Write protection of Sector12 */
+#define OB_PCROP_Pages416to447       (0x00002000U) /* PC Read/Write protection of Sector13 */
+#define OB_PCROP_Pages448to479       (0x00004000U) /* PC Read/Write protection of Sector14 */
+#define OB_PCROP_Pages480to511       (0x00008000U) /* PC Read/Write protection of Sector15 */
+#define OB_PCROP_AllPages            (0x0000FFFFU) /*!< PC Read/Write protection of all Sectors */
+/**
+  * @}
+  */
+#endif
+
+#if defined (STM32L071xx) || defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+/** @defgroup FLASHEx_Option_Bytes_PC_ReadWrite_Protection FLASH Option Bytes PC Read/Write Protection
+  * @{
+  */
+#define OB_PCROP_Pages0to31          (0x00000001U) /* PC Read/Write protection of Sector0 */
+#define OB_PCROP_Pages32to63         (0x00000002U) /* PC Read/Write protection of Sector1 */
+#define OB_PCROP_Pages64to95         (0x00000004U) /* PC Read/Write protection of Sector2 */
+#define OB_PCROP_Pages96to127        (0x00000008U) /* PC Read/Write protection of Sector3 */
+#define OB_PCROP_Pages128to159       (0x00000010U) /* PC Read/Write protection of Sector4 */
+#define OB_PCROP_Pages160to191       (0x00000020U) /* PC Read/Write protection of Sector5 */
+#define OB_PCROP_Pages192to223       (0x00000040U) /* PC Read/Write protection of Sector6 */
+#define OB_PCROP_Pages224to255       (0x00000080U) /* PC Read/Write protection of Sector7 */
+#define OB_PCROP_Pages256to287       (0x00000100U) /* PC Read/Write protection of Sector8 */
+#define OB_PCROP_Pages288to319       (0x00000200U) /* PC Read/Write protection of Sector9 */
+#define OB_PCROP_Pages320to351       (0x00000400U) /* PC Read/Write protection of Sector10 */
+#define OB_PCROP_Pages352to383       (0x00000800U) /* PC Read/Write protection of Sector11 */
+#define OB_PCROP_Pages384to415       (0x00001000U) /* PC Read/Write protection of Sector12 */
+#define OB_PCROP_Pages416to447       (0x00002000U) /* PC Read/Write protection of Sector13 */
+#define OB_PCROP_Pages448to479       (0x00004000U) /* PC Read/Write protection of Sector14 */
+#define OB_PCROP_Pages480to511       (0x00008000U) /* PC Read/Write protection of Sector15 */
+#define OB_PCROP_Pages512to543       (0x00010000U) /* PC Read/Write protection of Sector16 */
+#define OB_PCROP_Pages544to575       (0x00020000U) /* PC Read/Write protection of Sector17 */
+#define OB_PCROP_Pages576to607       (0x00040000U) /* PC Read/Write protection of Sector18 */
+#define OB_PCROP_Pages608to639       (0x00080000U) /* PC Read/Write protection of Sector19 */
+#define OB_PCROP_Pages640to671       (0x00100000U) /* PC Read/Write protection of Sector20 */
+#define OB_PCROP_Pages672to703       (0x00200000U) /* PC Read/Write protection of Sector21 */
+#define OB_PCROP_Pages704to735       (0x00400000U) /* PC Read/Write protection of Sector22 */
+#define OB_PCROP_Pages736to767       (0x00800000U) /* PC Read/Write protection of Sector23 */
+#define OB_PCROP_Pages768to799       (0x01000000U) /* PC Read/Write protection of Sector24 */
+#define OB_PCROP_Pages800to831       (0x02000000U) /* PC Read/Write protection of Sector25 */
+#define OB_PCROP_Pages832to863       (0x04000000U) /* PC Read/Write protection of Sector26 */
+#define OB_PCROP_Pages864to895       (0x08000000U) /* PC Read/Write protection of Sector27 */
+#define OB_PCROP_Pages896to927       (0x10000000U) /* PC Read/Write protection of Sector28 */
+#define OB_PCROP_Pages928to959       (0x20000000U) /* PC Read/Write protection of Sector29 */
+#define OB_PCROP_Pages960to991       (0x40000000U) /* PC Read/Write protection of Sector30 */
+#define OB_PCROP_Pages992to1023      (0x80000000U) /* PC Read/Write protection of Sector31 */
+#define OB_PCROP_AllPages            (0xFFFFFFFFU) /*!<PC Read/Write  protection of all Sectors */
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Option_Bytes_PC_ReadWrite_Protection2 FLASH Option Bytes PC Read/Write Protection (Sector 2)
+  * @{
+  */
+#define OB_PCROP2_Pages1024to1055    (0x00000001U) /* PC Read/Write protection of Sector32 */
+#define OB_PCROP2_Pages1056to1087    (0x00000002U) /* PC Read/Write protection of Sector33 */
+#define OB_PCROP2_Pages1088to1119    (0x00000004U) /* PC Read/Write protection of Sector34 */
+#define OB_PCROP2_Pages1120to1151    (0x00000008U) /* PC Read/Write protection of Sector35 */
+#define OB_PCROP2_Pages1152to1183    (0x00000010U) /* PC Read/Write protection of Sector36 */
+#define OB_PCROP2_Pages1184to1215    (0x00000020U) /* PC Read/Write protection of Sector37 */
+#define OB_PCROP2_Pages1216to1247    (0x00000040U) /* PC Read/Write protection of Sector38 */
+#define OB_PCROP2_Pages1248to1279    (0x00000080U) /* PC Read/Write protection of Sector39 */
+#define OB_PCROP2_Pages1280to1311    (0x00000100U) /* PC Read/Write protection of Sector40 */
+#define OB_PCROP2_Pages1312to1343    (0x00000200U) /* PC Read/Write protection of Sector41 */
+#define OB_PCROP2_Pages1344to1375    (0x00000400U) /* PC Read/Write protection of Sector42 */
+#define OB_PCROP2_Pages1376to1407    (0x00000800U) /* PC Read/Write protection of Sector43 */
+#define OB_PCROP2_Pages1408to1439    (0x00001000U) /* PC Read/Write protection of Sector44 */
+#define OB_PCROP2_Pages1440to1471    (0x00002000U) /* PC Read/Write protection of Sector45 */
+#define OB_PCROP2_Pages1472to1503    (0x00004000U) /* PC Read/Write protection of Sector46 */
+#define OB_PCROP2_Pages1504to1535    (0x00008000U) /* PC Read/Write protection of Sector47 */
+#define OB_PCROP2_AllPages           (0x0000FFFFU) /*!< PC Read/Write protection of all Sectors PCROP2 */
+/**
+  * @}
+  */
+#endif /* STM32L071xx || STM32L072xx || STM32L073xx || STM32L081xx || STM32L082xx || STM32L083xx */
+
+/** @defgroup FLASHEx_Option_Bytes_BOOTBit1 FLASH Option Bytes BOOT Bit1 Setup
+  * @{
+  */
+#define OB_BOOT_BIT1_RESET      (uint8_t)(0x00) /*!< BOOT Bit 1 Reset */
+#define OB_BOOT_BIT1_SET        (uint8_t)(0x01) /*!< BOOT Bit 1 Set */
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Type_Program_Data FLASHEx Type Program Data
+  * @{
+  */
+#define FLASH_TYPEPROGRAMDATA_BYTE            (0x00U)  /*!<Program byte (8-bit) at a specified address.*/
+#define FLASH_TYPEPROGRAMDATA_HALFWORD        (0x01U)  /*!<Program a half-word (16-bit) at a specified address.*/
+#define FLASH_TYPEPROGRAMDATA_WORD            (0x02U)  /*!<Program a word (32-bit) at a specified address.*/
+
+/**
+  * @}
+  */
+
+#if defined(FLASH_OPTR_BFB2)
+
+/** @defgroup FLASHEx_Option_Bytes_BOOT FLASHEx Option Bytes BOOT
+  * @{
+  */
+
+#define OB_BOOT_BANK1                 ((uint8_t)0x00) /*!<  At startup, if boot pin 0 and BOOT1 bit are set in boot from user Flash position
+                                                            and this parameter is selected the device will boot from Bank 1 (Default)*/
+#define OB_BOOT_BANK2                 ((uint8_t)(FLASH_OPTR_BFB2 >> 16)) /*!< At startup, if boot pin 0 and BOOT1 bit are set in boot from user Flash position
+                                                            and this parameter is selected the device will boot from Bank 2 */
+
+/**
+  * @}
+  */
+#endif /* FLASH_OPTR_BFB2 */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+
+/** @defgroup FLASHEx_Exported_Macros FLASHEx Exported Macros
+ *  @{
+ */
+
+/**
+  * @brief  Set the FLASH Latency.
+  * @param  __LATENCY__ FLASH Latency
+  *          This parameter can be one of the following values:
+  *            @arg @ref FLASH_LATENCY_0  FLASH Zero Latency cycle
+  *            @arg @ref FLASH_LATENCY_1  FLASH One Latency cycle
+  * @retval none
+  */
+#define __HAL_FLASH_SET_LATENCY(__LATENCY__) \
+                  MODIFY_REG(FLASH->ACR, FLASH_ACR_LATENCY, (uint32_t)(__LATENCY__))
+
+/**
+  * @brief  Get the FLASH Latency.
+  * @retval FLASH Latency
+  *          This parameter can be one of the following values:
+  *            @arg @ref FLASH_LATENCY_0  FLASH Zero Latency cycle
+  *            @arg @ref FLASH_LATENCY_1  FLASH One Latency cycle
+  */
+#define __HAL_FLASH_GET_LATENCY()     (READ_BIT((FLASH->ACR), FLASH_ACR_LATENCY))
+
+/**
+  * @brief  Enable the FLASH prefetch buffer.
+  * @retval none
+  */
+#define __HAL_FLASH_PREFETCH_BUFFER_ENABLE()      SET_BIT((FLASH->ACR), FLASH_ACR_PRFTEN)
+
+/**
+  * @brief  Disable the FLASH prefetch buffer.
+  * @retval none
+  */
+#define __HAL_FLASH_PREFETCH_BUFFER_DISABLE()     CLEAR_BIT((FLASH->ACR), FLASH_ACR_PRFTEN)
+
+/**
+  * @brief  Enable the FLASH Buffer cache.
+  * @retval none
+  */
+#define __HAL_FLASH_BUFFER_CACHE_ENABLE()         CLEAR_BIT((FLASH->ACR), FLASH_ACR_DISAB_BUF)
+
+/**
+  * @brief  Disable the FLASH Buffer cache.
+  * @retval none
+  */
+#define __HAL_FLASH_BUFFER_CACHE_DISABLE()        SET_BIT((FLASH->ACR), FLASH_ACR_DISAB_BUF)
+
+/**
+  * @brief  Enable the FLASH preread buffer.
+  * @retval none
+  */
+#define __HAL_FLASH_PREREAD_BUFFER_ENABLE()       SET_BIT((FLASH->ACR), FLASH_ACR_PRE_READ)
+
+/**
+  * @brief  Disable the FLASH preread buffer.
+  * @retval none
+  */
+#define __HAL_FLASH_PREREAD_BUFFER_DISABLE()      CLEAR_BIT((FLASH->ACR), FLASH_ACR_PRE_READ)
+
+/**
+  * @brief  Enable the FLASH power down during Sleep mode
+  * @retval none
+  */
+#define __HAL_FLASH_SLEEP_POWERDOWN_ENABLE()      SET_BIT(FLASH->ACR, FLASH_ACR_SLEEP_PD)
+
+/**
+  * @brief  Disable the FLASH power down during Sleep mode
+  * @retval none
+  */
+#define __HAL_FLASH_SLEEP_POWERDOWN_DISABLE()     CLEAR_BIT(FLASH->ACR, FLASH_ACR_SLEEP_PD)
+
+/**
+  * @brief  Enable the Flash Run power down mode.
+  * @note   Writing this bit  to 0 this bit, automatically the keys are
+  *         loss and a new unlock sequence is necessary to re-write it to 1.
+  */
+#define __HAL_FLASH_POWER_DOWN_ENABLE() do { FLASH->PDKEYR = FLASH_PDKEY1;    \
+                                             FLASH->PDKEYR = FLASH_PDKEY2;    \
+                                             SET_BIT((FLASH->ACR), FLASH_ACR_RUN_PD);  \
+                                           } while (0)
+
+/**
+  * @brief  Disable the Flash Run power down mode.
+  * @note   Writing this bit to 0 this bit, automatically the keys are
+  *         loss and a new unlock sequence is necessary to re-write it to 1.
+  */
+#define __HAL_FLASH_POWER_DOWN_DISABLE() do { FLASH->PDKEYR = FLASH_PDKEY1;    \
+                                              FLASH->PDKEYR = FLASH_PDKEY2;    \
+                                             CLEAR_BIT((FLASH->ACR), FLASH_ACR_RUN_PD);  \
+                                            } while (0)
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup FLASHEx_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup FLASHEx_Exported_Functions_Group1
+  * @{
+  */
+
+HAL_StatusTypeDef HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef *pEraseInit, uint32_t *PageError);
+HAL_StatusTypeDef HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef *pEraseInit);
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASHEx_Exported_Functions_Group2
+  * @{
+  */
+
+HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit);
+void              HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef *pOBInit);
+
+#if defined(FLASH_OPTR_WPRMOD) || defined(FLASH_OPTR_BFB2)
+
+HAL_StatusTypeDef HAL_FLASHEx_AdvOBProgram (FLASH_AdvOBProgramInitTypeDef *pAdvOBInit);
+void              HAL_FLASHEx_AdvOBGetConfig(FLASH_AdvOBProgramInitTypeDef *pAdvOBInit);
+
+#endif /* FLASH_OPTR_WPRMOD || FLASH_OPTR_BFB2 */
+
+#if defined(FLASH_OPTR_WPRMOD)
+
+HAL_StatusTypeDef HAL_FLASHEx_OB_SelectPCROP(void);
+HAL_StatusTypeDef HAL_FLASHEx_OB_DeSelectPCROP(void);
+
+#endif /* FLASH_OPTR_WPRMOD */
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASHEx_Exported_Functions_Group3
+  * @{
+  */
+
+HAL_StatusTypeDef HAL_FLASHEx_DATAEEPROM_Unlock(void);
+HAL_StatusTypeDef HAL_FLASHEx_DATAEEPROM_Lock(void);
+
+HAL_StatusTypeDef HAL_FLASHEx_DATAEEPROM_Erase(uint32_t Address);
+HAL_StatusTypeDef HAL_FLASHEx_DATAEEPROM_Program(uint32_t TypeProgram, uint32_t Address, uint32_t Data);
+void              HAL_FLASHEx_DATAEEPROM_EnableFixedTimeProgram(void);
+void              HAL_FLASHEx_DATAEEPROM_DisableFixedTimeProgram(void);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L0xx_HAL_FLASH_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_flash_ramfunc.h

@@ -0,0 +1,108 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_flash_ramfunc.h
+  * @author  MCD Application Team
+  * @brief   Header file of FLASH RAMFUNC driver.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics. 
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the 
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */ 
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_FLASH_RAMFUNC_H
+#define __STM32L0xx_FLASH_RAMFUNC_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup FLASH_RAMFUNC
+  * @{
+  */ 
+
+/* Exported types ------------------------------------------------------------*/ 
+
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup FLASH_RAMFUNC_Exported_Functions
+  * @{
+  */
+
+/*
+  * @brief  FLASH memory functions that should be executed from internal SRAM.
+  *         These functions are defined inside the "stm32l0xx_hal_flash_ramfunc.c"
+  *         file.
+  */
+  
+/** @addtogroup FLASH_RAMFUNC_Exported_Functions_Group1
+  * @{
+  */
+
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_EnableRunPowerDown(void);
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_DisableRunPowerDown(void);
+
+/**
+  * @}
+  */ 
+
+/** @addtogroup FLASH_RAMFUNC_Exported_Functions_Group2
+  * @{
+  */
+
+#if defined(FLASH_PECR_PARALLBANK)
+
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_EraseParallelPage(uint32_t Page_Address1, uint32_t Page_Address2);
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_ProgramParallelHalfPage(uint32_t Address1, uint32_t* pBuffer1, uint32_t Address2, uint32_t* pBuffer2);
+
+#endif /* FLASH_PECR_PARALLBANK */
+
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_HalfPageProgram(uint32_t Address, uint32_t* pBuffer);
+
+/**
+  * @}
+  */ 
+
+/** @addtogroup FLASH_RAMFUNC_Exported_Functions_Group3
+  * @{
+  */
+__RAM_FUNC  HAL_StatusTypeDef HAL_FLASHEx_GetError(uint32_t *Error);
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L0xx_FLASH_RAMFUNC_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_gpio.h

@@ -0,0 +1,343 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_gpio.h
+  * @author  MCD Application Team
+  * @brief   Header file of GPIO HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_GPIO_H
+#define __STM32L0xx_HAL_GPIO_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup GPIO GPIO
+  * @{
+  */
+/******************************************************************************/
+/* Exported types ------------------------------------------------------------*/
+/******************************************************************************/
+
+/** @defgroup GPIO_Exported_Types GPIO Exported Types
+  * @{
+  */
+
+/** @defgroup GPIO_Init_Configuration GPIO init configuration structure
+  * @{
+  */
+/**
+  * @brief   GPIO Init structure definition
+  */
+typedef struct
+{
+  uint32_t Pin;       /*!< Specifies the GPIO pins to be configured.
+                           This parameter can be a combination of @ref GPIO_pins_define */
+
+  uint32_t Mode;      /*!< Specifies the operating mode for the selected pins.
+                           This parameter can be a value of @ref GPIO_mode_define */
+
+  uint32_t Pull;      /*!< Specifies the Pull-up or Pull-Down activation for the selected pins.
+                           This parameter can be a value of @ref GPIO_pull_define */
+
+  uint32_t Speed;     /*!< Specifies the speed for the selected pins.
+                           This parameter can be a value of @ref GPIO_speed_define */
+
+  uint32_t Alternate;  /*!< Peripheral to be connected to the selected pins
+                            This parameter can be a value of @ref GPIOEx_Alternate_function_selection */
+} GPIO_InitTypeDef;
+/**
+  * @}
+  */
+
+/** @defgroup GPIO_SetReset_Definition  GPIO set reset definition
+  * @{
+  */
+/**
+  * @brief  GPIO Bit SET and Bit RESET enumeration
+  */
+typedef enum
+{
+  GPIO_PIN_RESET = 0U,
+  GPIO_PIN_SET
+} GPIO_PinState;
+/**
+  * @}
+  */
+
+
+#define IS_GPIO_PIN_ACTION(__ACTION__) (((__ACTION__) == GPIO_PIN_RESET) || ((__ACTION__) == GPIO_PIN_SET))
+
+/**
+  * @}
+  */
+/******************************************************************************/
+/* Exported constants --------------------------------------------------------*/
+/******************************************************************************/
+
+/** @defgroup GPIO_Exported_Constants GPIO Exported Constants
+  * @{
+  */
+
+/** @defgroup GPIO_pins_define Pin definition
+  * @{
+  */
+#define GPIO_PIN_0                 (0x0001U)  /* Pin 0 selected    */
+#define GPIO_PIN_1                 (0x0002U)  /* Pin 1 selected    */
+#define GPIO_PIN_2                 (0x0004U)  /* Pin 2 selected    */
+#define GPIO_PIN_3                 (0x0008U)  /* Pin 3 selected    */
+#define GPIO_PIN_4                 (0x0010U)  /* Pin 4 selected    */
+#define GPIO_PIN_5                 (0x0020U)  /* Pin 5 selected    */
+#define GPIO_PIN_6                 (0x0040U)  /* Pin 6 selected    */
+#define GPIO_PIN_7                 (0x0080U)  /* Pin 7 selected    */
+#define GPIO_PIN_8                 (0x0100U)  /* Pin 8 selected    */
+#define GPIO_PIN_9                 (0x0200U)  /* Pin 9 selected    */
+#define GPIO_PIN_10                (0x0400U)  /* Pin 10 selected   */
+#define GPIO_PIN_11                (0x0800U)  /* Pin 11 selected   */
+#define GPIO_PIN_12                (0x1000U)  /* Pin 12 selected   */
+#define GPIO_PIN_13                (0x2000U)  /* Pin 13 selected   */
+#define GPIO_PIN_14                (0x4000U)  /* Pin 14 selected   */
+#define GPIO_PIN_15                (0x8000U)  /* Pin 15 selected   */
+#define GPIO_PIN_All               (0xFFFFU)  /* All pins selected */
+/**
+  * @}
+  */
+
+#define GPIO_PIN_MASK              (0x0000FFFFU) /* PIN mask for assert test */
+#define IS_GPIO_PIN(__PIN__)        ((((uint32_t)(__PIN__) & GPIO_PIN_MASK) != 0x00U) &&\
+                                     (((uint32_t)(__PIN__) & ~GPIO_PIN_MASK) == 0x00U))
+
+/** @defgroup GPIO_mode_define Mode definition
+  * @brief GPIO Configuration Mode
+  *        Elements values convention: 0x00WX00YZ
+  *           - W  : EXTI trigger detection on 3 bits
+  *           - X  : EXTI mode (IT or Event) on 2 bits
+  *           - Y  : Output type (Push Pull or Open Drain) on 1 bit
+  *           - Z  : GPIO mode (Input, Output, Alternate or Analog) on 2 bits
+  * @{
+  */ 
+#define  GPIO_MODE_INPUT                        MODE_INPUT                                                  /*!< Input Floating Mode                   */
+#define  GPIO_MODE_OUTPUT_PP                    (MODE_OUTPUT | OUTPUT_PP)                                   /*!< Output Push Pull Mode                 */
+#define  GPIO_MODE_OUTPUT_OD                    (MODE_OUTPUT | OUTPUT_OD)                                   /*!< Output Open Drain Mode                */
+#define  GPIO_MODE_AF_PP                        (MODE_AF | OUTPUT_PP)                                       /*!< Alternate Function Push Pull Mode     */
+#define  GPIO_MODE_AF_OD                        (MODE_AF | OUTPUT_OD)                                       /*!< Alternate Function Open Drain Mode    */
+
+#define  GPIO_MODE_ANALOG                       MODE_ANALOG                                                 /*!< Analog Mode  */
+    
+#define  GPIO_MODE_IT_RISING                    (MODE_INPUT | EXTI_IT | TRIGGER_RISING)                     /*!< External Interrupt Mode with Rising edge trigger detection          */
+#define  GPIO_MODE_IT_FALLING                   (MODE_INPUT | EXTI_IT | TRIGGER_FALLING)                    /*!< External Interrupt Mode with Falling edge trigger detection         */
+#define  GPIO_MODE_IT_RISING_FALLING            (MODE_INPUT | EXTI_IT | TRIGGER_RISING | TRIGGER_FALLING)   /*!< External Interrupt Mode with Rising/Falling edge trigger detection  */
+ 
+#define  GPIO_MODE_EVT_RISING                   (MODE_INPUT | EXTI_EVT | TRIGGER_RISING)                     /*!< External Event Mode with Rising edge trigger detection             */
+#define  GPIO_MODE_EVT_FALLING                  (MODE_INPUT | EXTI_EVT | TRIGGER_FALLING)                    /*!< External Event Mode with Falling edge trigger detection            */
+#define  GPIO_MODE_EVT_RISING_FALLING           (MODE_INPUT | EXTI_EVT | TRIGGER_RISING | TRIGGER_FALLING)   /*!< External Event Mode with Rising/Falling edge trigger detection     */
+
+/**
+  * @}
+  */
+
+#define IS_GPIO_MODE(__MODE__) (((__MODE__) == GPIO_MODE_INPUT)              ||\
+                                ((__MODE__) == GPIO_MODE_OUTPUT_PP)          ||\
+                                ((__MODE__) == GPIO_MODE_OUTPUT_OD)          ||\
+                                ((__MODE__) == GPIO_MODE_AF_PP)              ||\
+                                ((__MODE__) == GPIO_MODE_AF_OD)              ||\
+                                ((__MODE__) == GPIO_MODE_IT_RISING)          ||\
+                                ((__MODE__) == GPIO_MODE_IT_FALLING)         ||\
+                                ((__MODE__) == GPIO_MODE_IT_RISING_FALLING)  ||\
+                                ((__MODE__) == GPIO_MODE_EVT_RISING)         ||\
+                                ((__MODE__) == GPIO_MODE_EVT_FALLING)        ||\
+                                ((__MODE__) == GPIO_MODE_EVT_RISING_FALLING) ||\
+                                ((__MODE__) == GPIO_MODE_ANALOG))
+
+
+/** @defgroup GPIO_speed_define Speed definition
+  * @brief GPIO Output Maximum frequency
+  * @{
+  */
+#define  GPIO_SPEED_FREQ_LOW              (0x00000000U)  /*!< range up to 0.4 MHz, please refer to the product datasheet */
+#define  GPIO_SPEED_FREQ_MEDIUM           (0x00000001U)  /*!< range 0.4 MHz to 2 MHz, please refer to the product datasheet */
+#define  GPIO_SPEED_FREQ_HIGH             (0x00000002U)  /*!< range   2 MHz to 10 MHz, please refer to the product datasheet */
+#define  GPIO_SPEED_FREQ_VERY_HIGH        (0x00000003U)  /*!< range  10 MHz to 35 MHz, please refer to the product datasheet */
+
+/**
+  * @}
+  */
+
+#define IS_GPIO_SPEED(__SPEED__) (((__SPEED__) == GPIO_SPEED_FREQ_LOW     )  || ((__SPEED__) == GPIO_SPEED_FREQ_MEDIUM     ) || \
+                                  ((__SPEED__) == GPIO_SPEED_FREQ_HIGH  ) || ((__SPEED__) == GPIO_SPEED_FREQ_VERY_HIGH))
+
+
+/** @defgroup GPIO_pull_define Pull definition
+  * @brief GPIO Pull-Up or Pull-Down Activation
+  * @{
+  */
+#define  GPIO_NOPULL        (0x00000000U)   /*!< No Pull-up or Pull-down activation  */
+#define  GPIO_PULLUP        (0x00000001U)   /*!< Pull-up activation                  */
+#define  GPIO_PULLDOWN      (0x00000002U)   /*!< Pull-down activation                */
+
+/**
+  * @}
+  */
+
+#define IS_GPIO_PULL(__PULL__) (((__PULL__) == GPIO_NOPULL) || ((__PULL__) == GPIO_PULLUP) || \
+                                ((__PULL__) == GPIO_PULLDOWN))
+
+
+/**
+  * @}
+  */
+/******************************************************************************/
+/* Exported macro ------------------------------------------------------------*/
+/******************************************************************************/
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup GPIO_Exported_Macro GPIO Exported Macros
+  * @{
+  */
+/**
+  * @brief  Checks whether the specified EXTI line flag is set or not.
+  * @param  __EXTI_LINE__ specifies the EXTI line flag to check.
+  *         This parameter can be GPIO_PIN_x where x can be(0..15)
+  * @retval The new state of __EXTI_LINE__ (SET or RESET).
+  */
+#define __HAL_GPIO_EXTI_GET_FLAG(__EXTI_LINE__) (EXTI->PR & (__EXTI_LINE__))
+
+/**
+  * @brief  Clears the EXTI's line pending flags.
+  * @param  __EXTI_LINE__ specifies the EXTI lines flags to clear.
+  *         This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
+  * @retval None
+  */
+#define __HAL_GPIO_EXTI_CLEAR_FLAG(__EXTI_LINE__) (EXTI->PR = (__EXTI_LINE__))
+
+/**
+  * @brief  Checks whether the specified EXTI line is asserted or not.
+  * @param  __EXTI_LINE__ specifies the EXTI line to check.
+  *          This parameter can be GPIO_PIN_x where x can be(0..15)
+  * @retval The new state of __EXTI_LINE__ (SET or RESET).
+  */
+#define __HAL_GPIO_EXTI_GET_IT(__EXTI_LINE__) (EXTI->PR & (__EXTI_LINE__))
+
+/**
+  * @brief  Clears the EXTI's line pending bits.
+  * @param  __EXTI_LINE__ specifies the EXTI lines to clear.
+  *          This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
+  * @retval None
+  */
+#define __HAL_GPIO_EXTI_CLEAR_IT(__EXTI_LINE__) (EXTI->PR = (__EXTI_LINE__))
+
+/**
+  * @brief  Generates a Software interrupt on selected EXTI line.
+  * @param  __EXTI_LINE__ specifies the EXTI line to check.
+  *          This parameter can be GPIO_PIN_x where x can be(0..15)
+  * @retval None
+  */
+#define __HAL_GPIO_EXTI_GENERATE_SWIT(__EXTI_LINE__) (EXTI->SWIER |= (__EXTI_LINE__))
+
+/**
+  * @}
+  */
+/* Include GPIO HAL Extension module */
+#include "stm32l0xx_hal_gpio_ex.h"
+
+/******************************************************************************/
+/* Exported functions --------------------------------------------------------*/
+/******************************************************************************/
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup GPIO_Exported_Functions GPIO Exported Functions
+  * @{
+  */
+
+/* Initialization and de-initialization functions *******************************/
+/** @defgroup GPIO_Exported_Functions_Group1 Initialization and de-initialization functions
+ *  @{
+ */
+void  HAL_GPIO_Init(GPIO_TypeDef  *GPIOx, GPIO_InitTypeDef *GPIO_Init);
+void  HAL_GPIO_DeInit(GPIO_TypeDef  *GPIOx, uint32_t GPIO_Pin);
+/**
+  * @}
+  */
+
+/* IO operation functions *******************************************************/
+/** @defgroup GPIO_Exported_Functions_Group2 IO operation functions
+ *  @{
+ */
+GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin);
+void          HAL_GPIO_WritePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState);
+void          HAL_GPIO_TogglePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin);
+HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin);
+void          HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin);
+void          HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Define the private group ***********************************/
+/**************************************************************/
+/** @defgroup GPIO_Private GPIO Private
+  * @{
+  */
+#define GPIO_MODE_Pos                           0U
+#define GPIO_MODE                               (0x3UL << GPIO_MODE_Pos)
+#define MODE_INPUT                              (0x0UL << GPIO_MODE_Pos)
+#define MODE_OUTPUT                             (0x1UL << GPIO_MODE_Pos)
+#define MODE_AF                                 (0x2UL << GPIO_MODE_Pos)
+#define MODE_ANALOG                             (0x3UL << GPIO_MODE_Pos)
+#define OUTPUT_TYPE_Pos                         4U
+#define OUTPUT_TYPE                             (0x1UL << OUTPUT_TYPE_Pos)
+#define OUTPUT_PP                               (0x0UL << OUTPUT_TYPE_Pos)
+#define OUTPUT_OD                               (0x1UL << OUTPUT_TYPE_Pos)
+#define EXTI_MODE_Pos                           16U
+#define EXTI_MODE                               (0x3UL << EXTI_MODE_Pos)
+#define EXTI_IT                                 (0x1UL << EXTI_MODE_Pos)
+#define EXTI_EVT                                (0x2UL << EXTI_MODE_Pos)
+#define TRIGGER_MODE_Pos                         20U
+#define TRIGGER_MODE                            (0x7UL << TRIGGER_MODE_Pos)
+#define TRIGGER_RISING                          (0x1UL << TRIGGER_MODE_Pos)
+#define TRIGGER_FALLING                         (0x2UL << TRIGGER_MODE_Pos)
+/**
+  * @}
+  */
+/**************************************************************/
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L0xx_HAL_GPIO_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_i2c.h

@@ -0,0 +1,838 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_i2c.h
+  * @author  MCD Application Team
+  * @brief   Header file of I2C HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32L0xx_HAL_I2C_H
+#define STM32L0xx_HAL_I2C_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup I2C
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup I2C_Exported_Types I2C Exported Types
+  * @{
+  */
+
+/** @defgroup I2C_Configuration_Structure_definition I2C Configuration Structure definition
+  * @brief  I2C Configuration Structure definition
+  * @{
+  */
+typedef struct
+{
+  uint32_t Timing;              /*!< Specifies the I2C_TIMINGR_register value.
+                                     This parameter calculated by referring to I2C initialization section
+                                     in Reference manual */
+
+  uint32_t OwnAddress1;         /*!< Specifies the first device own address.
+                                     This parameter can be a 7-bit or 10-bit address. */
+
+  uint32_t AddressingMode;      /*!< Specifies if 7-bit or 10-bit addressing mode is selected.
+                                     This parameter can be a value of @ref I2C_ADDRESSING_MODE */
+
+  uint32_t DualAddressMode;     /*!< Specifies if dual addressing mode is selected.
+                                     This parameter can be a value of @ref I2C_DUAL_ADDRESSING_MODE */
+
+  uint32_t OwnAddress2;         /*!< Specifies the second device own address if dual addressing mode is selected
+                                     This parameter can be a 7-bit address. */
+
+  uint32_t OwnAddress2Masks;    /*!< Specifies the acknowledge mask address second device own address if dual addressing
+                                     mode is selected.
+                                     This parameter can be a value of @ref I2C_OWN_ADDRESS2_MASKS */
+
+  uint32_t GeneralCallMode;     /*!< Specifies if general call mode is selected.
+                                     This parameter can be a value of @ref I2C_GENERAL_CALL_ADDRESSING_MODE */
+
+  uint32_t NoStretchMode;       /*!< Specifies if nostretch mode is selected.
+                                     This parameter can be a value of @ref I2C_NOSTRETCH_MODE */
+
+} I2C_InitTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_state_structure_definition HAL state structure definition
+  * @brief  HAL State structure definition
+  * @note  HAL I2C State value coding follow below described bitmap :\n
+  *          b7-b6  Error information\n
+  *             00 : No Error\n
+  *             01 : Abort (Abort user request on going)\n
+  *             10 : Timeout\n
+  *             11 : Error\n
+  *          b5     Peripheral initialization status\n
+  *             0  : Reset (peripheral not initialized)\n
+  *             1  : Init done (peripheral initialized and ready to use. HAL I2C Init function called)\n
+  *          b4     (not used)\n
+  *             x  : Should be set to 0\n
+  *          b3\n
+  *             0  : Ready or Busy (No Listen mode ongoing)\n
+  *             1  : Listen (peripheral in Address Listen Mode)\n
+  *          b2     Intrinsic process state\n
+  *             0  : Ready\n
+  *             1  : Busy (peripheral busy with some configuration or internal operations)\n
+  *          b1     Rx state\n
+  *             0  : Ready (no Rx operation ongoing)\n
+  *             1  : Busy (Rx operation ongoing)\n
+  *          b0     Tx state\n
+  *             0  : Ready (no Tx operation ongoing)\n
+  *             1  : Busy (Tx operation ongoing)
+  * @{
+  */
+typedef enum
+{
+  HAL_I2C_STATE_RESET             = 0x00U,   /*!< Peripheral is not yet Initialized         */
+  HAL_I2C_STATE_READY             = 0x20U,   /*!< Peripheral Initialized and ready for use  */
+  HAL_I2C_STATE_BUSY              = 0x24U,   /*!< An internal process is ongoing            */
+  HAL_I2C_STATE_BUSY_TX           = 0x21U,   /*!< Data Transmission process is ongoing      */
+  HAL_I2C_STATE_BUSY_RX           = 0x22U,   /*!< Data Reception process is ongoing         */
+  HAL_I2C_STATE_LISTEN            = 0x28U,   /*!< Address Listen Mode is ongoing            */
+  HAL_I2C_STATE_BUSY_TX_LISTEN    = 0x29U,   /*!< Address Listen Mode and Data Transmission
+                                                 process is ongoing                         */
+  HAL_I2C_STATE_BUSY_RX_LISTEN    = 0x2AU,   /*!< Address Listen Mode and Data Reception
+                                                 process is ongoing                         */
+  HAL_I2C_STATE_ABORT             = 0x60U,   /*!< Abort user request ongoing                */
+  HAL_I2C_STATE_TIMEOUT           = 0xA0U,   /*!< Timeout state                             */
+  HAL_I2C_STATE_ERROR             = 0xE0U    /*!< Error                                     */
+
+} HAL_I2C_StateTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_mode_structure_definition HAL mode structure definition
+  * @brief  HAL Mode structure definition
+  * @note  HAL I2C Mode value coding follow below described bitmap :\n
+  *          b7     (not used)\n
+  *             x  : Should be set to 0\n
+  *          b6\n
+  *             0  : None\n
+  *             1  : Memory (HAL I2C communication is in Memory Mode)\n
+  *          b5\n
+  *             0  : None\n
+  *             1  : Slave (HAL I2C communication is in Slave Mode)\n
+  *          b4\n
+  *             0  : None\n
+  *             1  : Master (HAL I2C communication is in Master Mode)\n
+  *          b3-b2-b1-b0  (not used)\n
+  *             xxxx : Should be set to 0000
+  * @{
+  */
+typedef enum
+{
+  HAL_I2C_MODE_NONE               = 0x00U,   /*!< No I2C communication on going             */
+  HAL_I2C_MODE_MASTER             = 0x10U,   /*!< I2C communication is in Master Mode       */
+  HAL_I2C_MODE_SLAVE              = 0x20U,   /*!< I2C communication is in Slave Mode        */
+  HAL_I2C_MODE_MEM                = 0x40U    /*!< I2C communication is in Memory Mode       */
+
+} HAL_I2C_ModeTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup I2C_Error_Code_definition I2C Error Code definition
+  * @brief  I2C Error Code definition
+  * @{
+  */
+#define HAL_I2C_ERROR_NONE      (0x00000000U)    /*!< No error              */
+#define HAL_I2C_ERROR_BERR      (0x00000001U)    /*!< BERR error            */
+#define HAL_I2C_ERROR_ARLO      (0x00000002U)    /*!< ARLO error            */
+#define HAL_I2C_ERROR_AF        (0x00000004U)    /*!< ACKF error            */
+#define HAL_I2C_ERROR_OVR       (0x00000008U)    /*!< OVR error             */
+#define HAL_I2C_ERROR_DMA       (0x00000010U)    /*!< DMA transfer error    */
+#define HAL_I2C_ERROR_TIMEOUT   (0x00000020U)    /*!< Timeout error         */
+#define HAL_I2C_ERROR_SIZE      (0x00000040U)    /*!< Size Management error */
+#define HAL_I2C_ERROR_DMA_PARAM (0x00000080U)    /*!< DMA Parameter Error   */
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+#define HAL_I2C_ERROR_INVALID_CALLBACK  (0x00000100U)    /*!< Invalid Callback error */
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
+#define HAL_I2C_ERROR_INVALID_PARAM     (0x00000200U)    /*!< Invalid Parameters error  */
+/**
+  * @}
+  */
+
+/** @defgroup I2C_handle_Structure_definition I2C handle Structure definition
+  * @brief  I2C handle Structure definition
+  * @{
+  */
+typedef struct __I2C_HandleTypeDef
+{
+  I2C_TypeDef                *Instance;      /*!< I2C registers base address                */
+
+  I2C_InitTypeDef            Init;           /*!< I2C communication parameters              */
+
+  uint8_t                    *pBuffPtr;      /*!< Pointer to I2C transfer buffer            */
+
+  uint16_t                   XferSize;       /*!< I2C transfer size                         */
+
+  __IO uint16_t              XferCount;      /*!< I2C transfer counter                      */
+
+  __IO uint32_t              XferOptions;    /*!< I2C sequantial transfer options, this parameter can
+                                                  be a value of @ref I2C_XFEROPTIONS */
+
+  __IO uint32_t              PreviousState;  /*!< I2C communication Previous state          */
+
+  HAL_StatusTypeDef(*XferISR)(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);
+  /*!< I2C transfer IRQ handler function pointer */
+
+  DMA_HandleTypeDef          *hdmatx;        /*!< I2C Tx DMA handle parameters              */
+
+  DMA_HandleTypeDef          *hdmarx;        /*!< I2C Rx DMA handle parameters              */
+
+  HAL_LockTypeDef            Lock;           /*!< I2C locking object                        */
+
+  __IO HAL_I2C_StateTypeDef  State;          /*!< I2C communication state                   */
+
+  __IO HAL_I2C_ModeTypeDef   Mode;           /*!< I2C communication mode                    */
+
+  __IO uint32_t              ErrorCode;      /*!< I2C Error code                            */
+
+  __IO uint32_t              AddrEventCount; /*!< I2C Address Event counter                 */
+
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+  void (* MasterTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Master Tx Transfer completed callback */
+  void (* MasterRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Master Rx Transfer completed callback */
+  void (* SlaveTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Slave Tx Transfer completed callback  */
+  void (* SlaveRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Slave Rx Transfer completed callback  */
+  void (* ListenCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Listen Complete callback              */
+  void (* MemTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Memory Tx Transfer completed callback */
+  void (* MemRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Memory Rx Transfer completed callback */
+  void (* ErrorCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Error callback                        */
+  void (* AbortCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Abort callback                        */
+
+  void (* AddrCallback)(struct __I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode);
+  /*!< I2C Slave Address Match callback */
+
+  void (* MspInitCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Msp Init callback                     */
+  void (* MspDeInitCallback)(struct __I2C_HandleTypeDef *hi2c);
+  /*!< I2C Msp DeInit callback                   */
+
+#endif  /* USE_HAL_I2C_REGISTER_CALLBACKS */
+} I2C_HandleTypeDef;
+
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL I2C Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_I2C_MASTER_TX_COMPLETE_CB_ID      = 0x00U,    /*!< I2C Master Tx Transfer completed callback ID  */
+  HAL_I2C_MASTER_RX_COMPLETE_CB_ID      = 0x01U,    /*!< I2C Master Rx Transfer completed callback ID  */
+  HAL_I2C_SLAVE_TX_COMPLETE_CB_ID       = 0x02U,    /*!< I2C Slave Tx Transfer completed callback ID   */
+  HAL_I2C_SLAVE_RX_COMPLETE_CB_ID       = 0x03U,    /*!< I2C Slave Rx Transfer completed callback ID   */
+  HAL_I2C_LISTEN_COMPLETE_CB_ID         = 0x04U,    /*!< I2C Listen Complete callback ID               */
+  HAL_I2C_MEM_TX_COMPLETE_CB_ID         = 0x05U,    /*!< I2C Memory Tx Transfer callback ID            */
+  HAL_I2C_MEM_RX_COMPLETE_CB_ID         = 0x06U,    /*!< I2C Memory Rx Transfer completed callback ID  */
+  HAL_I2C_ERROR_CB_ID                   = 0x07U,    /*!< I2C Error callback ID                         */
+  HAL_I2C_ABORT_CB_ID                   = 0x08U,    /*!< I2C Abort callback ID                         */
+
+  HAL_I2C_MSPINIT_CB_ID                 = 0x09U,    /*!< I2C Msp Init callback ID                      */
+  HAL_I2C_MSPDEINIT_CB_ID               = 0x0AU     /*!< I2C Msp DeInit callback ID                    */
+
+} HAL_I2C_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL I2C Callback pointer definition
+  */
+typedef  void (*pI2C_CallbackTypeDef)(I2C_HandleTypeDef *hi2c);
+/*!< pointer to an I2C callback function */
+typedef  void (*pI2C_AddrCallbackTypeDef)(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection,
+                                          uint16_t AddrMatchCode);
+/*!< pointer to an I2C Address Match callback function */
+
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup I2C_Exported_Constants I2C Exported Constants
+  * @{
+  */
+
+/** @defgroup I2C_XFEROPTIONS  I2C Sequential Transfer Options
+  * @{
+  */
+#define I2C_FIRST_FRAME                 ((uint32_t)I2C_SOFTEND_MODE)
+#define I2C_FIRST_AND_NEXT_FRAME        ((uint32_t)(I2C_RELOAD_MODE | I2C_SOFTEND_MODE))
+#define I2C_NEXT_FRAME                  ((uint32_t)(I2C_RELOAD_MODE | I2C_SOFTEND_MODE))
+#define I2C_FIRST_AND_LAST_FRAME        ((uint32_t)I2C_AUTOEND_MODE)
+#define I2C_LAST_FRAME                  ((uint32_t)I2C_AUTOEND_MODE)
+#define I2C_LAST_FRAME_NO_STOP          ((uint32_t)I2C_SOFTEND_MODE)
+
+/* List of XferOptions in usage of :
+ * 1- Restart condition in all use cases (direction change or not)
+ */
+#define  I2C_OTHER_FRAME                (0x000000AAU)
+#define  I2C_OTHER_AND_LAST_FRAME       (0x0000AA00U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_ADDRESSING_MODE I2C Addressing Mode
+  * @{
+  */
+#define I2C_ADDRESSINGMODE_7BIT         (0x00000001U)
+#define I2C_ADDRESSINGMODE_10BIT        (0x00000002U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_DUAL_ADDRESSING_MODE I2C Dual Addressing Mode
+  * @{
+  */
+#define I2C_DUALADDRESS_DISABLE         (0x00000000U)
+#define I2C_DUALADDRESS_ENABLE          I2C_OAR2_OA2EN
+/**
+  * @}
+  */
+
+/** @defgroup I2C_OWN_ADDRESS2_MASKS I2C Own Address2 Masks
+  * @{
+  */
+#define I2C_OA2_NOMASK                  ((uint8_t)0x00U)
+#define I2C_OA2_MASK01                  ((uint8_t)0x01U)
+#define I2C_OA2_MASK02                  ((uint8_t)0x02U)
+#define I2C_OA2_MASK03                  ((uint8_t)0x03U)
+#define I2C_OA2_MASK04                  ((uint8_t)0x04U)
+#define I2C_OA2_MASK05                  ((uint8_t)0x05U)
+#define I2C_OA2_MASK06                  ((uint8_t)0x06U)
+#define I2C_OA2_MASK07                  ((uint8_t)0x07U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_GENERAL_CALL_ADDRESSING_MODE I2C General Call Addressing Mode
+  * @{
+  */
+#define I2C_GENERALCALL_DISABLE         (0x00000000U)
+#define I2C_GENERALCALL_ENABLE          I2C_CR1_GCEN
+/**
+  * @}
+  */
+
+/** @defgroup I2C_NOSTRETCH_MODE I2C No-Stretch Mode
+  * @{
+  */
+#define I2C_NOSTRETCH_DISABLE           (0x00000000U)
+#define I2C_NOSTRETCH_ENABLE            I2C_CR1_NOSTRETCH
+/**
+  * @}
+  */
+
+/** @defgroup I2C_MEMORY_ADDRESS_SIZE I2C Memory Address Size
+  * @{
+  */
+#define I2C_MEMADD_SIZE_8BIT            (0x00000001U)
+#define I2C_MEMADD_SIZE_16BIT           (0x00000002U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_XFERDIRECTION I2C Transfer Direction Master Point of View
+  * @{
+  */
+#define I2C_DIRECTION_TRANSMIT          (0x00000000U)
+#define I2C_DIRECTION_RECEIVE           (0x00000001U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_RELOAD_END_MODE I2C Reload End Mode
+  * @{
+  */
+#define  I2C_RELOAD_MODE                I2C_CR2_RELOAD
+#define  I2C_AUTOEND_MODE               I2C_CR2_AUTOEND
+#define  I2C_SOFTEND_MODE               (0x00000000U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_START_STOP_MODE I2C Start or Stop Mode
+  * @{
+  */
+#define  I2C_NO_STARTSTOP               (0x00000000U)
+#define  I2C_GENERATE_STOP              (uint32_t)(0x80000000U | I2C_CR2_STOP)
+#define  I2C_GENERATE_START_READ        (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN)
+#define  I2C_GENERATE_START_WRITE       (uint32_t)(0x80000000U | I2C_CR2_START)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_Interrupt_configuration_definition I2C Interrupt configuration definition
+  * @brief I2C Interrupt definition
+  *        Elements values convention: 0xXXXXXXXX
+  *           - XXXXXXXX  : Interrupt control mask
+  * @{
+  */
+#define I2C_IT_ERRI                     I2C_CR1_ERRIE
+#define I2C_IT_TCI                      I2C_CR1_TCIE
+#define I2C_IT_STOPI                    I2C_CR1_STOPIE
+#define I2C_IT_NACKI                    I2C_CR1_NACKIE
+#define I2C_IT_ADDRI                    I2C_CR1_ADDRIE
+#define I2C_IT_RXI                      I2C_CR1_RXIE
+#define I2C_IT_TXI                      I2C_CR1_TXIE
+/**
+  * @}
+  */
+
+/** @defgroup I2C_Flag_definition I2C Flag definition
+  * @{
+  */
+#define I2C_FLAG_TXE                    I2C_ISR_TXE
+#define I2C_FLAG_TXIS                   I2C_ISR_TXIS
+#define I2C_FLAG_RXNE                   I2C_ISR_RXNE
+#define I2C_FLAG_ADDR                   I2C_ISR_ADDR
+#define I2C_FLAG_AF                     I2C_ISR_NACKF
+#define I2C_FLAG_STOPF                  I2C_ISR_STOPF
+#define I2C_FLAG_TC                     I2C_ISR_TC
+#define I2C_FLAG_TCR                    I2C_ISR_TCR
+#define I2C_FLAG_BERR                   I2C_ISR_BERR
+#define I2C_FLAG_ARLO                   I2C_ISR_ARLO
+#define I2C_FLAG_OVR                    I2C_ISR_OVR
+#define I2C_FLAG_PECERR                 I2C_ISR_PECERR
+#define I2C_FLAG_TIMEOUT                I2C_ISR_TIMEOUT
+#define I2C_FLAG_ALERT                  I2C_ISR_ALERT
+#define I2C_FLAG_BUSY                   I2C_ISR_BUSY
+#define I2C_FLAG_DIR                    I2C_ISR_DIR
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+
+/** @defgroup I2C_Exported_Macros I2C Exported Macros
+  * @{
+  */
+
+/** @brief Reset I2C handle state.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+#define __HAL_I2C_RESET_HANDLE_STATE(__HANDLE__)                do{                                             \
+                                                                    (__HANDLE__)->State = HAL_I2C_STATE_RESET;  \
+                                                                    (__HANDLE__)->MspInitCallback = NULL;       \
+                                                                    (__HANDLE__)->MspDeInitCallback = NULL;     \
+                                                                  } while(0)
+#else
+#define __HAL_I2C_RESET_HANDLE_STATE(__HANDLE__)                ((__HANDLE__)->State = HAL_I2C_STATE_RESET)
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
+
+/** @brief  Enable the specified I2C interrupt.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __INTERRUPT__ specifies the interrupt source to enable.
+  *        This parameter can be one of the following values:
+  *            @arg @ref I2C_IT_ERRI  Errors interrupt enable
+  *            @arg @ref I2C_IT_TCI   Transfer complete interrupt enable
+  *            @arg @ref I2C_IT_STOPI STOP detection interrupt enable
+  *            @arg @ref I2C_IT_NACKI NACK received interrupt enable
+  *            @arg @ref I2C_IT_ADDRI Address match interrupt enable
+  *            @arg @ref I2C_IT_RXI   RX interrupt enable
+  *            @arg @ref I2C_IT_TXI   TX interrupt enable
+  *
+  * @retval None
+  */
+#define __HAL_I2C_ENABLE_IT(__HANDLE__, __INTERRUPT__)          ((__HANDLE__)->Instance->CR1 |= (__INTERRUPT__))
+
+/** @brief  Disable the specified I2C interrupt.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __INTERRUPT__ specifies the interrupt source to disable.
+  *        This parameter can be one of the following values:
+  *            @arg @ref I2C_IT_ERRI  Errors interrupt enable
+  *            @arg @ref I2C_IT_TCI   Transfer complete interrupt enable
+  *            @arg @ref I2C_IT_STOPI STOP detection interrupt enable
+  *            @arg @ref I2C_IT_NACKI NACK received interrupt enable
+  *            @arg @ref I2C_IT_ADDRI Address match interrupt enable
+  *            @arg @ref I2C_IT_RXI   RX interrupt enable
+  *            @arg @ref I2C_IT_TXI   TX interrupt enable
+  *
+  * @retval None
+  */
+#define __HAL_I2C_DISABLE_IT(__HANDLE__, __INTERRUPT__)         ((__HANDLE__)->Instance->CR1 &= (~(__INTERRUPT__)))
+
+/** @brief  Check whether the specified I2C interrupt source is enabled or not.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __INTERRUPT__ specifies the I2C interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg @ref I2C_IT_ERRI  Errors interrupt enable
+  *            @arg @ref I2C_IT_TCI   Transfer complete interrupt enable
+  *            @arg @ref I2C_IT_STOPI STOP detection interrupt enable
+  *            @arg @ref I2C_IT_NACKI NACK received interrupt enable
+  *            @arg @ref I2C_IT_ADDRI Address match interrupt enable
+  *            @arg @ref I2C_IT_RXI   RX interrupt enable
+  *            @arg @ref I2C_IT_TXI   TX interrupt enable
+  *
+  * @retval The new state of __INTERRUPT__ (SET or RESET).
+  */
+#define __HAL_I2C_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)      ((((__HANDLE__)->Instance->CR1 & \
+                                                                   (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
+
+/** @brief  Check whether the specified I2C flag is set or not.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __FLAG__ specifies the flag to check.
+  *        This parameter can be one of the following values:
+  *            @arg @ref I2C_FLAG_TXE     Transmit data register empty
+  *            @arg @ref I2C_FLAG_TXIS    Transmit interrupt status
+  *            @arg @ref I2C_FLAG_RXNE    Receive data register not empty
+  *            @arg @ref I2C_FLAG_ADDR    Address matched (slave mode)
+  *            @arg @ref I2C_FLAG_AF      Acknowledge failure received flag
+  *            @arg @ref I2C_FLAG_STOPF   STOP detection flag
+  *            @arg @ref I2C_FLAG_TC      Transfer complete (master mode)
+  *            @arg @ref I2C_FLAG_TCR     Transfer complete reload
+  *            @arg @ref I2C_FLAG_BERR    Bus error
+  *            @arg @ref I2C_FLAG_ARLO    Arbitration lost
+  *            @arg @ref I2C_FLAG_OVR     Overrun/Underrun
+  *            @arg @ref I2C_FLAG_PECERR  PEC error in reception
+  *            @arg @ref I2C_FLAG_TIMEOUT Timeout or Tlow detection flag
+  *            @arg @ref I2C_FLAG_ALERT   SMBus alert
+  *            @arg @ref I2C_FLAG_BUSY    Bus busy
+  *            @arg @ref I2C_FLAG_DIR     Transfer direction (slave mode)
+  *
+  * @retval The new state of __FLAG__ (SET or RESET).
+  */
+#define I2C_FLAG_MASK  (0x0001FFFFU)
+#define __HAL_I2C_GET_FLAG(__HANDLE__, __FLAG__) (((((__HANDLE__)->Instance->ISR) & \
+                                                    (__FLAG__)) == (__FLAG__)) ? SET : RESET)
+
+/** @brief  Clear the I2C pending flags which are cleared by writing 1 in a specific bit.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __FLAG__ specifies the flag to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg @ref I2C_FLAG_TXE     Transmit data register empty
+  *            @arg @ref I2C_FLAG_ADDR    Address matched (slave mode)
+  *            @arg @ref I2C_FLAG_AF      Acknowledge failure received flag
+  *            @arg @ref I2C_FLAG_STOPF   STOP detection flag
+  *            @arg @ref I2C_FLAG_BERR    Bus error
+  *            @arg @ref I2C_FLAG_ARLO    Arbitration lost
+  *            @arg @ref I2C_FLAG_OVR     Overrun/Underrun
+  *            @arg @ref I2C_FLAG_PECERR  PEC error in reception
+  *            @arg @ref I2C_FLAG_TIMEOUT Timeout or Tlow detection flag
+  *            @arg @ref I2C_FLAG_ALERT   SMBus alert
+  *
+  * @retval None
+  */
+#define __HAL_I2C_CLEAR_FLAG(__HANDLE__, __FLAG__) (((__FLAG__) == I2C_FLAG_TXE) ? \
+                                                    ((__HANDLE__)->Instance->ISR |= (__FLAG__)) : \
+                                                    ((__HANDLE__)->Instance->ICR = (__FLAG__)))
+
+/** @brief  Enable the specified I2C peripheral.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#define __HAL_I2C_ENABLE(__HANDLE__)                         (SET_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))
+
+/** @brief  Disable the specified I2C peripheral.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#define __HAL_I2C_DISABLE(__HANDLE__)                        (CLEAR_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))
+
+/** @brief  Generate a Non-Acknowledge I2C peripheral in Slave mode.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#define __HAL_I2C_GENERATE_NACK(__HANDLE__)                  (SET_BIT((__HANDLE__)->Instance->CR2, I2C_CR2_NACK))
+/**
+  * @}
+  */
+
+/* Include I2C HAL Extended module */
+#include "stm32l0xx_hal_i2c_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup I2C_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup I2C_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+/* Initialization and de-initialization functions******************************/
+HAL_StatusTypeDef HAL_I2C_Init(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2C_DeInit(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MspInit(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MspDeInit(I2C_HandleTypeDef *hi2c);
+
+/* Callbacks Register/UnRegister functions  ***********************************/
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+HAL_StatusTypeDef HAL_I2C_RegisterCallback(I2C_HandleTypeDef *hi2c, HAL_I2C_CallbackIDTypeDef CallbackID,
+                                           pI2C_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_I2C_UnRegisterCallback(I2C_HandleTypeDef *hi2c, HAL_I2C_CallbackIDTypeDef CallbackID);
+
+HAL_StatusTypeDef HAL_I2C_RegisterAddrCallback(I2C_HandleTypeDef *hi2c, pI2C_AddrCallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_I2C_UnRegisterAddrCallback(I2C_HandleTypeDef *hi2c);
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @addtogroup I2C_Exported_Functions_Group2 Input and Output operation functions
+  * @{
+  */
+/* IO operation functions  ****************************************************/
+/******* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_I2C_Master_Transmit(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                          uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Master_Receive(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                         uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+                                         uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Slave_Receive(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+                                        uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Mem_Write(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                    uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Mem_Read(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                   uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_IsDeviceReady(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint32_t Trials,
+                                        uint32_t Timeout);
+
+/******* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_I2C_Master_Transmit_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                             uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Master_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                            uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Receive_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Write_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                       uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Read_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                      uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Transmit_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                                 uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                                uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Transmit_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+                                                uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Receive_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+                                               uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_EnableListen_IT(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2C_DisableListen_IT(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2C_Master_Abort_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress);
+
+/******* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_I2C_Master_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                              uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Master_Receive_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                             uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Receive_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Write_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                        uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Read_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
+                                       uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                                  uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Receive_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+                                                 uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+                                                 uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Receive_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+                                                uint32_t XferOptions);
+/**
+  * @}
+  */
+
+/** @addtogroup I2C_IRQ_Handler_and_Callbacks IRQ Handler and Callbacks
+  * @{
+  */
+/******* I2C IRQHandler and Callbacks used in non blocking modes (Interrupt and DMA) */
+void HAL_I2C_EV_IRQHandler(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_ER_IRQHandler(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MasterTxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MasterRxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_SlaveTxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_SlaveRxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_AddrCallback(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode);
+void HAL_I2C_ListenCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MemTxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MemRxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_ErrorCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_AbortCpltCallback(I2C_HandleTypeDef *hi2c);
+/**
+  * @}
+  */
+
+/** @addtogroup I2C_Exported_Functions_Group3 Peripheral State, Mode and Error functions
+  * @{
+  */
+/* Peripheral State, Mode and Error functions  *********************************/
+HAL_I2C_StateTypeDef HAL_I2C_GetState(I2C_HandleTypeDef *hi2c);
+HAL_I2C_ModeTypeDef  HAL_I2C_GetMode(I2C_HandleTypeDef *hi2c);
+uint32_t             HAL_I2C_GetError(I2C_HandleTypeDef *hi2c);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup I2C_Private_Constants I2C Private Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup I2C_Private_Macro I2C Private Macros
+  * @{
+  */
+
+#define IS_I2C_ADDRESSING_MODE(MODE)    (((MODE) == I2C_ADDRESSINGMODE_7BIT) || \
+                                         ((MODE) == I2C_ADDRESSINGMODE_10BIT))
+
+#define IS_I2C_DUAL_ADDRESS(ADDRESS)    (((ADDRESS) == I2C_DUALADDRESS_DISABLE) || \
+                                         ((ADDRESS) == I2C_DUALADDRESS_ENABLE))
+
+#define IS_I2C_OWN_ADDRESS2_MASK(MASK)  (((MASK) == I2C_OA2_NOMASK)  || \
+                                         ((MASK) == I2C_OA2_MASK01) || \
+                                         ((MASK) == I2C_OA2_MASK02) || \
+                                         ((MASK) == I2C_OA2_MASK03) || \
+                                         ((MASK) == I2C_OA2_MASK04) || \
+                                         ((MASK) == I2C_OA2_MASK05) || \
+                                         ((MASK) == I2C_OA2_MASK06) || \
+                                         ((MASK) == I2C_OA2_MASK07))
+
+#define IS_I2C_GENERAL_CALL(CALL)       (((CALL) == I2C_GENERALCALL_DISABLE) || \
+                                         ((CALL) == I2C_GENERALCALL_ENABLE))
+
+#define IS_I2C_NO_STRETCH(STRETCH)      (((STRETCH) == I2C_NOSTRETCH_DISABLE) || \
+                                         ((STRETCH) == I2C_NOSTRETCH_ENABLE))
+
+#define IS_I2C_MEMADD_SIZE(SIZE)        (((SIZE) == I2C_MEMADD_SIZE_8BIT) || \
+                                         ((SIZE) == I2C_MEMADD_SIZE_16BIT))
+
+#define IS_TRANSFER_MODE(MODE)          (((MODE) == I2C_RELOAD_MODE)   || \
+                                         ((MODE) == I2C_AUTOEND_MODE) || \
+                                         ((MODE) == I2C_SOFTEND_MODE))
+
+#define IS_TRANSFER_REQUEST(REQUEST)    (((REQUEST) == I2C_GENERATE_STOP)        || \
+                                         ((REQUEST) == I2C_GENERATE_START_READ)  || \
+                                         ((REQUEST) == I2C_GENERATE_START_WRITE) || \
+                                         ((REQUEST) == I2C_NO_STARTSTOP))
+
+#define IS_I2C_TRANSFER_OPTIONS_REQUEST(REQUEST)  (((REQUEST) == I2C_FIRST_FRAME)          || \
+                                                   ((REQUEST) == I2C_FIRST_AND_NEXT_FRAME) || \
+                                                   ((REQUEST) == I2C_NEXT_FRAME)           || \
+                                                   ((REQUEST) == I2C_FIRST_AND_LAST_FRAME) || \
+                                                   ((REQUEST) == I2C_LAST_FRAME)           || \
+                                                   ((REQUEST) == I2C_LAST_FRAME_NO_STOP)   || \
+                                                   IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(REQUEST))
+
+#define IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(REQUEST) (((REQUEST) == I2C_OTHER_FRAME)     || \
+                                                        ((REQUEST) == I2C_OTHER_AND_LAST_FRAME))
+
+#define I2C_RESET_CR2(__HANDLE__)                 ((__HANDLE__)->Instance->CR2 &= \
+                                                   (uint32_t)~((uint32_t)(I2C_CR2_SADD   | I2C_CR2_HEAD10R | \
+                                                                          I2C_CR2_NBYTES | I2C_CR2_RELOAD  | \
+                                                                          I2C_CR2_RD_WRN)))
+
+#define I2C_GET_ADDR_MATCH(__HANDLE__)            ((uint16_t)(((__HANDLE__)->Instance->ISR & I2C_ISR_ADDCODE) \
+                                                              >> 16U))
+#define I2C_GET_DIR(__HANDLE__)                   ((uint8_t)(((__HANDLE__)->Instance->ISR & I2C_ISR_DIR) \
+                                                             >> 16U))
+#define I2C_GET_STOP_MODE(__HANDLE__)             ((__HANDLE__)->Instance->CR2 & I2C_CR2_AUTOEND)
+#define I2C_GET_OWN_ADDRESS1(__HANDLE__)          ((uint16_t)((__HANDLE__)->Instance->OAR1 & I2C_OAR1_OA1))
+#define I2C_GET_OWN_ADDRESS2(__HANDLE__)          ((uint16_t)((__HANDLE__)->Instance->OAR2 & I2C_OAR2_OA2))
+
+#define IS_I2C_OWN_ADDRESS1(ADDRESS1)             ((ADDRESS1) <= 0x000003FFU)
+#define IS_I2C_OWN_ADDRESS2(ADDRESS2)             ((ADDRESS2) <= (uint16_t)0x00FFU)
+
+#define I2C_MEM_ADD_MSB(__ADDRESS__)              ((uint8_t)((uint16_t)(((uint16_t)((__ADDRESS__) & \
+                                                                         (uint16_t)(0xFF00U))) >> 8U)))
+#define I2C_MEM_ADD_LSB(__ADDRESS__)              ((uint8_t)((uint16_t)((__ADDRESS__) & (uint16_t)(0x00FFU))))
+
+#define I2C_GENERATE_START(__ADDMODE__,__ADDRESS__) (((__ADDMODE__) == I2C_ADDRESSINGMODE_7BIT) ? \
+                                                     (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | \
+                                                                 (I2C_CR2_START) | (I2C_CR2_AUTOEND)) & \
+                                                                (~I2C_CR2_RD_WRN)) : \
+                                                     (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | \
+                                                                 (I2C_CR2_ADD10) | (I2C_CR2_START)) & \
+                                                                (~I2C_CR2_RD_WRN)))
+
+#define I2C_CHECK_FLAG(__ISR__, __FLAG__)         ((((__ISR__) & ((__FLAG__) & I2C_FLAG_MASK)) == \
+                                                    ((__FLAG__) & I2C_FLAG_MASK)) ? SET : RESET)
+#define I2C_CHECK_IT_SOURCE(__CR1__, __IT__)      ((((__CR1__) & (__IT__)) == (__IT__)) ? SET : RESET)
+/**
+  * @}
+  */
+
+/* Private Functions ---------------------------------------------------------*/
+/** @defgroup I2C_Private_Functions I2C Private Functions
+  * @{
+  */
+/* Private functions are defined in stm32l0xx_hal_i2c.c file */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* STM32L0xx_HAL_I2C_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_i2c_ex.h

@@ -0,0 +1,196 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_i2c_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of I2C HAL Extended module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32L0xx_HAL_I2C_EX_H
+#define STM32L0xx_HAL_I2C_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup I2CEx
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup I2CEx_Exported_Constants I2C Extended Exported Constants
+  * @{
+  */
+
+/** @defgroup I2CEx_Analog_Filter I2C Extended Analog Filter
+  * @{
+  */
+#define I2C_ANALOGFILTER_ENABLE         0x00000000U
+#define I2C_ANALOGFILTER_DISABLE        I2C_CR1_ANFOFF
+/**
+  * @}
+  */
+
+/** @defgroup I2CEx_FastModePlus I2C Extended Fast Mode Plus
+  * @{
+  */
+#define I2C_FMP_NOT_SUPPORTED           0xAAAA0000U                                     /*!< Fast Mode Plus not supported       */
+#if defined(SYSCFG_CFGR2_I2C_PB6_FMP)
+#define I2C_FASTMODEPLUS_PB6            SYSCFG_CFGR2_I2C_PB6_FMP                        /*!< Enable Fast Mode Plus on PB6       */
+#define I2C_FASTMODEPLUS_PB7            SYSCFG_CFGR2_I2C_PB7_FMP                        /*!< Enable Fast Mode Plus on PB7       */
+#else
+#define I2C_FASTMODEPLUS_PB6            (uint32_t)(0x00000004U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus PB6 not supported   */
+#define I2C_FASTMODEPLUS_PB7            (uint32_t)(0x00000008U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus PB7 not supported   */
+#endif /* SYSCFG_CFGR2_I2C_PB6_FMP */
+#if defined(SYSCFG_CFGR2_I2C_PB8_FMP)
+#define I2C_FASTMODEPLUS_PB8            SYSCFG_CFGR2_I2C_PB8_FMP                        /*!< Enable Fast Mode Plus on PB8       */
+#define I2C_FASTMODEPLUS_PB9            SYSCFG_CFGR2_I2C_PB9_FMP                        /*!< Enable Fast Mode Plus on PB9       */
+#else
+#define I2C_FASTMODEPLUS_PB8            (uint32_t)(0x00000010U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus PB8 not supported   */
+#define I2C_FASTMODEPLUS_PB9            (uint32_t)(0x00000012U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus PB9 not supported   */
+#endif /* SYSCFG_CFGR2_I2C_PB8_FMP */
+#if defined(SYSCFG_CFGR2_I2C1_FMP)
+#define I2C_FASTMODEPLUS_I2C1           SYSCFG_CFGR2_I2C1_FMP                           /*!< Enable Fast Mode Plus on I2C1 pins */
+#else
+#define I2C_FASTMODEPLUS_I2C1           (uint32_t)(0x00000100U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus I2C1 not supported  */
+#endif /* SYSCFG_CFGR2_I2C1_FMP */
+#if defined(SYSCFG_CFGR2_I2C2_FMP)
+#define I2C_FASTMODEPLUS_I2C2           SYSCFG_CFGR2_I2C2_FMP                           /*!< Enable Fast Mode Plus on I2C2 pins */
+#else
+#define I2C_FASTMODEPLUS_I2C2           (uint32_t)(0x00000200U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus I2C2 not supported  */
+#endif /* SYSCFG_CFGR2_I2C2_FMP */
+#if defined(SYSCFG_CFGR2_I2C3_FMP)
+#define I2C_FASTMODEPLUS_I2C3           SYSCFG_CFGR2_I2C3_FMP                           /*!< Enable Fast Mode Plus on I2C3 pins */
+#else
+#define I2C_FASTMODEPLUS_I2C3           (uint32_t)(0x00000400U | I2C_FMP_NOT_SUPPORTED) /*!< Fast Mode Plus I2C3 not supported  */
+#endif /* SYSCFG_CFGR2_I2C3_FMP */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup I2CEx_Exported_Macros I2C Extended Exported Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup I2CEx_Exported_Functions I2C Extended Exported Functions
+  * @{
+  */
+
+/** @addtogroup I2CEx_Exported_Functions_Group1 Filter Mode Functions
+  * @{
+  */
+/* Peripheral Control functions  ************************************************/
+HAL_StatusTypeDef HAL_I2CEx_ConfigAnalogFilter(I2C_HandleTypeDef *hi2c, uint32_t AnalogFilter);
+HAL_StatusTypeDef HAL_I2CEx_ConfigDigitalFilter(I2C_HandleTypeDef *hi2c, uint32_t DigitalFilter);
+/**
+  * @}
+  */
+
+/** @addtogroup I2CEx_Exported_Functions_Group2 WakeUp Mode Functions
+  * @{
+  */
+HAL_StatusTypeDef HAL_I2CEx_EnableWakeUp(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2CEx_DisableWakeUp(I2C_HandleTypeDef *hi2c);
+/**
+  * @}
+  */
+#if  (defined(SYSCFG_CFGR2_I2C_PB6_FMP) || defined(SYSCFG_CFGR2_I2C_PB7_FMP)) || (defined(SYSCFG_CFGR2_I2C_PB8_FMP) || defined(SYSCFG_CFGR2_I2C_PB9_FMP)) || (defined(SYSCFG_CFGR2_I2C1_FMP)) || defined(SYSCFG_CFGR2_I2C2_FMP) || defined(SYSCFG_CFGR2_I2C3_FMP)
+
+/** @addtogroup I2CEx_Exported_Functions_Group3 Fast Mode Plus Functions
+  * @{
+  */
+void HAL_I2CEx_EnableFastModePlus(uint32_t ConfigFastModePlus);
+void HAL_I2CEx_DisableFastModePlus(uint32_t ConfigFastModePlus);
+/**
+  * @}
+  */
+#endif /* Fast Mode Plus Availability */
+
+/**
+  * @}
+  */
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup I2CEx_Private_Constants I2C Extended Private Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup I2CEx_Private_Macro I2C Extended Private Macros
+  * @{
+  */
+#define IS_I2C_ANALOG_FILTER(FILTER)    (((FILTER) == I2C_ANALOGFILTER_ENABLE) || \
+                                         ((FILTER) == I2C_ANALOGFILTER_DISABLE))
+
+#define IS_I2C_DIGITAL_FILTER(FILTER)   ((FILTER) <= 0x0000000FU)
+
+#define IS_I2C_FASTMODEPLUS(__CONFIG__) ((((__CONFIG__) & I2C_FMP_NOT_SUPPORTED) != I2C_FMP_NOT_SUPPORTED) && \
+                                         ((((__CONFIG__) & (I2C_FASTMODEPLUS_PB6))  == I2C_FASTMODEPLUS_PB6)     || \
+                                          (((__CONFIG__) & (I2C_FASTMODEPLUS_PB7))  == I2C_FASTMODEPLUS_PB7)     || \
+                                          (((__CONFIG__) & (I2C_FASTMODEPLUS_PB8))  == I2C_FASTMODEPLUS_PB8)     || \
+                                          (((__CONFIG__) & (I2C_FASTMODEPLUS_PB9))  == I2C_FASTMODEPLUS_PB9)     || \
+                                          (((__CONFIG__) & (I2C_FASTMODEPLUS_I2C1)) == I2C_FASTMODEPLUS_I2C1)    || \
+                                          (((__CONFIG__) & (I2C_FASTMODEPLUS_I2C2)) == I2C_FASTMODEPLUS_I2C2)    || \
+                                          (((__CONFIG__) & (I2C_FASTMODEPLUS_I2C3)) == I2C_FASTMODEPLUS_I2C3)))
+/**
+  * @}
+  */
+
+/* Private Functions ---------------------------------------------------------*/
+/** @defgroup I2CEx_Private_Functions I2C Extended Private Functions
+  * @{
+  */
+/* Private functions are defined in stm32l0xx_hal_i2c_ex.c file */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32L0xx_HAL_I2C_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_pwr.h

@@ -0,0 +1,460 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_pwr.h
+  * @author  MCD Application Team
+  * @brief   Header file of PWR HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_PWR_H
+#define __STM32L0xx_HAL_PWR_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup PWR PWR
+  * @{
+  */
+
+/** @defgroup PWR_Exported_Types PWR Exported Types
+  * @{
+  */ 
+
+#if defined(PWR_PVD_SUPPORT)
+/**
+  * @brief  PWR PVD configuration structure definition
+  */
+typedef struct
+{
+  uint32_t PVDLevel;   /*!< PVDLevel: Specifies the PVD detection level.
+                            This parameter can be a value of @ref PWR_PVD_detection_level */
+
+  uint32_t Mode;       /*!< Mode: Specifies the operating mode for the selected pins.
+                            This parameter can be a value of @ref PWR_PVD_Mode */
+}PWR_PVDTypeDef;
+#endif
+
+/**
+  * @}
+  */
+
+/** @addtogroup PWR_Private
+  * @{
+  */ 
+
+#if defined(PWR_PVD_SUPPORT)
+#define PWR_EXTI_LINE_PVD      EXTI_FTSR_TR16  /*!< External interrupt line 16 Connected to the PVD EXTI Line */
+#endif
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Exported_Constants PWR Exported Constants
+  * @{
+  */
+
+/** @defgroup PWR_register_alias_address PWR Register alias address
+  * @{
+  */
+#define PWR_WAKEUP_PIN1                PWR_CSR_EWUP1
+#if defined (STM32L010x4) || defined (STM32L011xx) || defined (STM32L021xx)
+#else
+#define PWR_WAKEUP_PIN2                PWR_CSR_EWUP2
+#endif
+#if defined (STM32L010x4) || defined (STM32L010x6) || defined (STM32L011xx) || defined (STM32L021xx) || \
+    defined (STM32L031xx) || defined (STM32L041xx) || defined (STM32L071xx) || defined (STM32L072xx) || \
+    defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+#define PWR_WAKEUP_PIN3                PWR_CSR_EWUP3
+#endif
+/**
+  * @}
+  */
+
+#if defined(PWR_PVD_SUPPORT)
+/** @defgroup PWR_PVD_detection_level PVD detection level
+  * @{
+  */
+#define PWR_PVDLEVEL_0                 PWR_CR_PLS_LEV0
+#define PWR_PVDLEVEL_1                 PWR_CR_PLS_LEV1
+#define PWR_PVDLEVEL_2                 PWR_CR_PLS_LEV2
+#define PWR_PVDLEVEL_3                 PWR_CR_PLS_LEV3
+#define PWR_PVDLEVEL_4                 PWR_CR_PLS_LEV4
+#define PWR_PVDLEVEL_5                 PWR_CR_PLS_LEV5
+#define PWR_PVDLEVEL_6                 PWR_CR_PLS_LEV6
+#define PWR_PVDLEVEL_7                 PWR_CR_PLS_LEV7  /* External input analog voltage 
+                                                           (Compare internally to VREFINT) */
+/**
+  * @}
+  */
+
+/** @defgroup PWR_PVD_Mode PWR PVD Mode
+  * @{
+  */
+#define PWR_PVD_MODE_NORMAL                 (0x00000000U)   /*!< basic mode is used */
+#define PWR_PVD_MODE_IT_RISING              (0x00010001U)   /*!< External Interrupt Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_IT_FALLING             (0x00010002U)   /*!< External Interrupt Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_IT_RISING_FALLING      (0x00010003U)   /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING           (0x00020001U)   /*!< Event Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_EVENT_FALLING          (0x00020002U)   /*!< Event Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING_FALLING   (0x00020003U)   /*!< Event Mode with Rising/Falling edge trigger detection */
+/**
+  * @}
+  */
+#endif /* PWR_PVD_SUPPORT */
+
+/** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR Regulator state in SLEEP/STOP mode
+  * @{
+  */
+#define PWR_MAINREGULATOR_ON           (0x00000000U)
+#define PWR_LOWPOWERREGULATOR_ON       PWR_CR_LPSDSR
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
+  * @{
+  */
+#define PWR_SLEEPENTRY_WFI             (0x01U)
+#define PWR_SLEEPENTRY_WFE             (0x02U)
+/**
+  * @}
+  */
+
+/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
+  * @{
+  */
+#define PWR_STOPENTRY_WFI              (0x01U)
+#define PWR_STOPENTRY_WFE              (0x02U)
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Regulator_Voltage_Scale PWR Regulator Voltage Scale
+  * @{
+  */
+
+#define PWR_REGULATOR_VOLTAGE_SCALE1   PWR_CR_VOS_0
+#define PWR_REGULATOR_VOLTAGE_SCALE2   PWR_CR_VOS_1
+#define PWR_REGULATOR_VOLTAGE_SCALE3   PWR_CR_VOS
+
+#define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
+                                             ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \
+                                             ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE3))
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Flag PWR Flag
+  * @{
+  */
+#define PWR_FLAG_WU                    PWR_CSR_WUF
+#define PWR_FLAG_SB                    PWR_CSR_SBF
+#if defined(PWR_PVD_SUPPORT)
+#define PWR_FLAG_PVDO                  PWR_CSR_PVDO
+#endif
+#define PWR_FLAG_VREFINTRDY            PWR_CSR_VREFINTRDYF
+#define PWR_FLAG_VOS                   PWR_CSR_VOSF
+#define PWR_FLAG_REGLP                 PWR_CSR_REGLPF
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Exported_Macro PWR Exported Macros
+  * @{
+  */
+/** @brief  macros configure the main internal regulator output voltage.
+  *         When exiting Low Power Run Mode or during dynamic voltage scaling configuration,
+  *         the reference manual recommends to poll PWR_FLAG_REGLP bit to wait for the regulator 
+  *         to reach main mode (resp. to get stabilized) for a transition from 0 to 1. 
+  *         Only then the clock can be increased.
+  *
+  * @param  __REGULATOR__ specifies the regulator output voltage to achieve
+  *         a tradeoff between performance and power consumption when the device does
+  *         not operate at the maximum frequency (refer to the datasheets for more details).
+  *          This parameter can be one of the following values:
+  *            @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode,
+  *                                                System frequency up to 32 MHz.
+  *            @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode,
+  *                                                System frequency up to 16 MHz.
+  *            @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode,
+  *                                                System frequency up to 4.2 MHz
+  * @retval None
+  */
+#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) (MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)))
+
+/** @brief  Check PWR flag is set or not.
+  * @param  __FLAG__ specifies the flag to check.
+  *           This parameter can be one of the following values:
+  *            @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
+  *                  was received from the WKUP pin or from the RTC alarm (Alarm B),
+  *                  RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
+  *                  An additional wakeup event is detected if the WKUP pin is enabled
+  *                  (by setting the EWUP bit) when the WKUP pin level is already high.
+  *            @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
+  *                  resumed from StandBy mode.
+  *            @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled 
+  *                  by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode.
+  *                  For this reason, this bit is equal to 0 after Standby or reset
+  *                  until the PVDE bit is set. Not available on L0 Value line.
+  *            @arg PWR_FLAG_VREFINTRDY: Internal voltage reference (VREFINT) ready flag.
+  *                 This bit indicates the state of the internal voltage reference, VREFINT.
+  *            @arg PWR_FLAG_VOS: Voltage Scaling select flag. A delay is required for
+  *                 the internal regulator to be ready after the voltage range is changed.
+  *                 The VOSF bit indicates that the regulator has reached the voltage level
+  *                 defined with bits VOS of PWR_CR register.
+  *            @arg PWR_FLAG_REGLP: Regulator LP flag. When the MCU exits from Low power run
+  *                 mode, this bit stays at 1 until the regulator is ready in main mode.
+  *                 A polling on this bit is recommended to wait for the regulator main mode.
+  *                 This bit is reset by hardware when the regulator is ready.
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_PWR_GET_FLAG(__FLAG__)                  ((PWR->CSR & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clear the PWR pending flags.
+  * @param  __FLAG__ specifies the flag to clear.
+  *          This parameter can be one of the following values:
+  *            @arg PWR_FLAG_WU: Wake Up flag
+  *            @arg PWR_FLAG_SB: StandBy flag
+  */
+#define __HAL_PWR_CLEAR_FLAG(__FLAG__)                SET_BIT(PWR->CR, (__FLAG__) << 2U)
+
+#if defined(PWR_PVD_SUPPORT)
+/**
+  * @brief Enable interrupt on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_IT()      SET_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable interrupt on PVD Exti Line 16. 
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_IT()     CLEAR_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Enable event on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT()   SET_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable event on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT()  CLEAR_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief  PVD EXTI line configuration: set falling edge trigger.  
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE()  SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable the PVD Extended Interrupt Falling Trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE()  CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief  PVD EXTI line configuration: set rising edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE()   SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable the PVD Extended Interrupt Rising Trigger.
+  * This parameter can be:
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE()  CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief  PVD EXTI line configuration: set rising & falling edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE()   do { __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); } while(0);
+
+/**
+  * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger.
+  * This parameter can be:
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE()  do { __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); } while(0);
+
+/**
+  * @brief Check whether the specified PVD EXTI interrupt flag is set or not.
+  * @retval EXTI PVD Line Status.
+  */
+#define __HAL_PWR_PVD_EXTI_GET_FLAG()       (EXTI->PR & (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Clear the PVD EXTI flag.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG()     (EXTI->PR = (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Generate a Software interrupt on selected EXTI line.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT()  SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Generate a Software interrupt on selected EXTI line.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT()            SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)
+
+#endif /* PWR_PVD_SUPPORT */
+
+/**
+  * @}
+  */
+
+/** @addtogroup PWR_Private
+  * @{
+  */
+#if defined(PWR_PVD_SUPPORT)
+#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7))
+
+#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \
+                               ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \
+                               ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \
+                               ((MODE) == PWR_PVD_MODE_NORMAL)) 
+#endif /* PWR_PVD_SUPPORT */
+
+#if defined (STM32L010x6) || defined (STM32L071xx) || defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+                                ((PIN) == PWR_WAKEUP_PIN2) || \
+                                ((PIN) == PWR_WAKEUP_PIN3))
+#elif defined (STM32L010xB) || defined (STM32L051xx) || defined (STM32L052xx) || defined (STM32L053xx) || defined (STM32L062xx) || defined (STM32L063xx)
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+                                ((PIN) == PWR_WAKEUP_PIN2))
+#elif defined (STM32L010x8) || defined (STM32L031xx) || defined (STM32L041xx)
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+                                ((PIN) == PWR_WAKEUP_PIN2))
+#elif defined (STM32L010x4) || defined (STM32L011xx) || defined (STM32L021xx)
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+                                ((PIN) == PWR_WAKEUP_PIN3))
+#endif
+
+#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
+                                     ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))
+#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))
+
+#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE))
+
+/**
+  * @}
+  */
+
+/* Include PWR HAL Extension module */
+#include "stm32l0xx_hal_pwr_ex.h"
+
+/** @defgroup PWR_Exported_Functions PWR Exported Functions
+  * @{
+  */
+  
+/** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions 
+  * @{
+  */
+void HAL_PWR_DeInit(void);
+void HAL_PWR_EnableBkUpAccess(void);
+void HAL_PWR_DisableBkUpAccess(void);
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Exported_Functions_Group2 Low Power modes configuration functions
+  * @{
+  */
+
+#if defined(PWR_PVD_SUPPORT)
+/* PVD control functions  ************************************************/
+void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD);
+void HAL_PWR_EnablePVD(void);
+void HAL_PWR_DisablePVD(void);
+void HAL_PWR_PVD_IRQHandler(void);
+void HAL_PWR_PVDCallback(void);
+#endif
+
+/* WakeUp pins configuration functions ****************************************/
+void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx);
+void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);
+
+/* Low Power modes configuration functions ************************************/
+void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
+void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
+void HAL_PWR_EnterSTANDBYMode(void);
+
+void HAL_PWR_EnableSleepOnExit(void);
+void HAL_PWR_DisableSleepOnExit(void);
+void HAL_PWR_EnableSEVOnPend(void);
+void HAL_PWR_DisableSEVOnPend(void);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Define the private group ***********************************/
+/**************************************************************/
+/** @defgroup PWR_Private PWR Private
+  * @{
+  */
+/**
+  * @}
+  */
+/**************************************************************/
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* __STM32L0xx_HAL_PWR_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_pwr_ex.h

@@ -0,0 +1,99 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_pwr_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of PWR HAL Extension module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_PWR_EX_H
+#define __STM32L0xx_HAL_PWR_EX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup PWREx PWREx
+  * @{
+  */
+
+/** @defgroup PWREx_Exported_Macros PWREx Exported Macros
+ * @{
+ */
+
+/** @brief  Macros to enable the Deep-sleep mode with Flash memory kept off.
+  * @note   When entering low power mode (stop or standby only), if DS_EE_KOFF and RUN_PD of
+  *         FLASH_ACR register are both set , the Flash memory will not be woken up 
+  *         when exiting from deep-sleep mode.
+  */
+#define __HAL_PWR_FLASHWAKEUP_ENABLE()      CLEAR_BIT(PWR->CR, PWR_CR_DSEEKOFF)
+
+/** @brief  Macros to disable the Deep-sleep mode with Flash memory kept off.
+  * @note   When entering low power mode (stop or standby only), if DS_EE_KOFF and RUN_PD of
+  *         FLASH_ACR register are both set , the Flash memory will not be woken up 
+  *         when exiting from deep-sleep mode.
+  */
+#define __HAL_PWR_FLASHWAKEUP_DISABLE()     SET_BIT(PWR->CR, PWR_CR_DSEEKOFF)
+/**
+  * @}
+  */
+
+/** @defgroup PWREx_Exported_Functions PWREx Exported Functions
+ * @{
+ */
+uint32_t HAL_PWREx_GetVoltageRange(void);
+void HAL_PWREx_EnableFastWakeUp(void);
+void HAL_PWREx_DisableFastWakeUp(void);
+void HAL_PWREx_EnableUltraLowPower(void);
+void HAL_PWREx_DisableUltraLowPower(void);
+void HAL_PWREx_EnableLowPowerRunMode(void);
+HAL_StatusTypeDef HAL_PWREx_DisableLowPowerRunMode(void);
+/**
+  * @}
+  */
+
+/* Define the private group ***********************************/
+/**************************************************************/
+/** @defgroup PWREx_Private PWREx Private
+  * @{
+  */
+/**
+  * @}
+  */
+/**************************************************************/
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L0xx_HAL_PWR_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_tim_ex.h

@@ -0,0 +1,247 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_tim_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of TIM HAL Extended module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32L0xx_HAL_TIM_EX_H
+#define STM32L0xx_HAL_TIM_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup TIMEx
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Types TIM Extended Exported Types
+  * @{
+  */
+
+/**
+  * @}
+  */
+/* End of exported types -----------------------------------------------------*/
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Constants TIM Extended Exported Constants
+  * @{
+  */
+
+/** @defgroup TIMEx_Remap TIM Extended Remapping
+  * @{
+  */
+#define TIM2_ETR_GPIO                     0x00000000U                               /*!< TIM2 ETR input is connected to ORed GPIOs */
+#if defined(RCC_HSI48_SUPPORT)
+#define TIM2_ETR_HSI48                    TIM2_OR_ETR_RMP_2                         /*!< TIM2 ETR input is connected to HSI48 clock */
+#endif /* RCC_HSI48_SUPPORT */
+#define TIM2_ETR_HSI16                    (TIM2_OR_ETR_RMP_1 | TIM2_OR_ETR_RMP_0)   /*!< TIM2 ETR input is connected to HSI16 clock */
+#define TIM2_ETR_LSE                      (TIM2_OR_ETR_RMP_2 | TIM2_OR_ETR_RMP_0)   /*!< TIM2 ETR input is connected to LSE clock */
+#if defined(COMP1) && defined(COMP2)
+#define TIM2_ETR_COMP2_OUT                (TIM2_OR_ETR_RMP_2 | TIM2_OR_ETR_RMP_1)   /*!< TIM2 ETR input is connected to COMP2_OUT */
+#define TIM2_ETR_COMP1_OUT                TIM2_OR_ETR_RMP                           /*!< TIM2 ETR input is connected to COMP1_OUT */
+#endif /* COMP1 && COMP2 */
+
+#define TIM2_TI4_GPIO                     0x00000000U                               /*!< TIM2 TI4 input connected to ORed GPIOs */
+#if defined(COMP1) && defined(COMP2)
+#define TIM2_TI4_COMP2                    TIM2_OR_TI4_RMP_0                         /*!< TIM2 TI4 input connected to COMP2_OUT */
+#define TIM2_TI4_COMP1                    TIM2_OR_TI4_RMP_1                         /*!< TIM2 TI4 input connected to COMP1_OUT */
+#endif /* COMP1 && COMP2 */
+
+#if defined(TIM3)
+#if defined(USB)
+#define TIM3_TI4_USB_NOE                  0x00000000U                               /*!< USB_NOE selected selected for PC9 (AF2) remapping */
+#endif /* USB */
+
+#define TIM3_TI4_GPIOC9_AF2               TIM3_OR_TI4_RMP                           /*!< TIM3_CH4 selected for PC9 (AF2) remapping */
+#define TIM3_TI2_GPIO_DEF                 0x00000000U                               /*!< TIM3_CH2 selected for PB5 (AF4) remapping */
+#define TIM3_TI2_GPIOB5_AF4               TIM3_OR_TI2_RMP                           /*!< TIM22_CH2 selected for PB5 (AF4) remapping */
+
+#if defined(USB)
+#define TIM3_TI1_USB_SOF                  0x00000000U                               /*!< TIM3 TI1 input connected to USB_SOF */
+#endif /* USB */
+
+#define TIM3_TI1_GPIO                     TIM3_OR_TI1_RMP                           /*!< TIM3 TI1 input connected to ORed GPIOs */
+#define TIM3_ETR_GPIO                     0x00000000U                               /*!< TIM3 ETR input connected to ORed GPIOs */
+#define TIM3_ETR_HSI                      TIM3_OR_ETR_RMP_1                         /*!< TIM3_ETR input is connected to HSI48 clock */
+#endif /* TIM3 */
+
+#define TIM21_ETR_GPIO                    0x00000000U                               /*!< TIM21 ETR input connected to ORed GPIOs */
+#if defined(COMP1) && defined(COMP2)
+#define TIM21_ETR_COMP2_OUT               TIM21_OR_ETR_RMP_0                        /*!< TIM21 ETR input connected to COMP2_OUT */
+#define TIM21_ETR_COMP1_OUT               TIM21_OR_ETR_RMP_1                        /*!< TIM21 ETR input connected to COMP1_OUT */
+#endif /* COMP1 && COMP2 */
+#define TIM21_ETR_LSE                     TIM21_OR_ETR_RMP                          /*!< TIM21 ETR input connected to LSE clock */
+
+#define TIM21_TI1_GPIO                    0x00000000U                               /*!< TIM21 TI1 input connected to ORed GPIOs */
+#define TIM21_TI1_MCO                     TIM21_OR_TI1_RMP                          /*!< TIM21 TI1 input connected to MCO clock */
+#define TIM21_TI1_RTC_WKUT_IT             TIM21_OR_TI1_RMP_0                        /*!< TIM21 TI1 input connected to RTC WAKEUP interrupt */
+#define TIM21_TI1_HSE_RTC                 TIM21_OR_TI1_RMP_1                        /*!< TIM21 TI1 input connected to HSE_RTC clock */
+#define TIM21_TI1_MSI                     (TIM21_OR_TI1_RMP_0 | TIM21_OR_TI1_RMP_1) /*!< TIM21 TI1 input connected to MSI clock */
+#define TIM21_TI1_LSE                     TIM21_OR_TI1_RMP_2                        /*!< TIM21 TI1 input connected to LSE clock */
+#define TIM21_TI1_LSI                     (TIM21_OR_TI1_RMP_2 | TIM21_OR_TI1_RMP_0) /*!< TIM21 TI1 input connected to LSI clock */
+#if defined(COMP1)
+#define TIM21_TI1_COMP1_OUT               (TIM21_OR_TI1_RMP_2 | TIM21_OR_TI1_RMP_1) /*!< TIM21 TI1 input connected to COMP1_OUT */
+#endif /* COMP1 */
+
+#define TIM21_TI2_GPIO                    0x00000000U                               /*!< TIM21 TI2 input connected to ORed GPIOs */
+#if defined(COMP2)
+#define TIM21_TI2_COMP2_OUT               TIM21_OR_TI2_RMP                          /*!< TIM21 TI2 input connected to COMP2_OUT */
+#endif /* COMP2 */
+
+#if defined(TIM22)
+#define TIM22_ETR_GPIO                    0x00000000U                               /*!< TIM22 ETR input is connected to ORed GPIOs */
+#if defined(COMP1) && defined(COMP2)
+#define TIM22_ETR_COMP2_OUT               TIM22_OR_ETR_RMP_0                        /*!< TIM22 ETR input is connected to COMP2_OUT */
+#define TIM22_ETR_COMP1_OUT               TIM22_OR_ETR_RMP_1                        /*!< TIM22 ETR input is connected to COMP1_OUT */
+#endif /* COMP1 && COMP2 */
+#define TIM22_ETR_LSE                     TIM22_OR_ETR_RMP                          /*!< TIM22 ETR input is connected to LSE clock */
+
+#define TIM22_TI1_GPIO                   0x00000000U                                /*!< TIM22 TI1 input is connected to ORed GPIOs */
+#if defined(COMP1) && defined(COMP2)
+#define TIM22_TI1_COMP2_OUT               TIM22_OR_TI1_RMP_0                        /*!< TIM22 TI1 input is connected to COMP2_OUT */
+#define TIM22_TI1_COMP1_OUT               TIM22_OR_TI1_RMP_1                        /*!< TIM22 TI1 input is connected to COMP1_OUT */
+#endif /* COMP1 && COMP2 */
+#endif /* TIM22 */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* End of exported constants -------------------------------------------------*/
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Macros TIM Extended Exported Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+/* End of exported macro -----------------------------------------------------*/
+
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup TIMEx_Private_Macros TIM Extended Private Macros
+  * @{
+  */
+#if defined(TIM3) && defined(TIM22)
+
+#define IS_TIM_REMAP(__INSTANCE__, __TIM_REMAP__)               \
+  ((((__INSTANCE__) == TIM2)   &&  ((__TIM_REMAP__) <=  (TIM2_OR_TI4_RMP  | TIM2_OR_ETR_RMP))) || \
+   (((__INSTANCE__) == TIM22)  &&  ((__TIM_REMAP__) <=  (TIM22_OR_TI1_RMP | TIM22_OR_ETR_RMP))) || \
+   (((__INSTANCE__) == TIM21)  &&  ((__TIM_REMAP__) <=  (TIM21_OR_ETR_RMP | TIM21_OR_TI1_RMP | TIM21_OR_TI2_RMP))) || \
+   (((__INSTANCE__) == TIM3)   &&  ((__TIM_REMAP__) <=  (TIM3_OR_ETR_RMP  | TIM3_OR_TI1_RMP  | TIM3_OR_TI2_RMP | TIM3_OR_TI4_RMP))))
+
+#define IS_CHANNEL_AVAILABLE(__INSTANCE__, __CHANNEL__)     \
+  ((((__INSTANCE__) == TIM2)  &&  (((__CHANNEL__) == TIM_CHANNEL_1)   ||   \
+                                   ((__CHANNEL__) == TIM_CHANNEL_2)   ||   \
+                                   ((__CHANNEL__) == TIM_CHANNEL_3)   ||   \
+                                   ((__CHANNEL__) == TIM_CHANNEL_4))) ||   \
+   (((__INSTANCE__) == TIM3) &&   (((__CHANNEL__) == TIM_CHANNEL_1)   ||   \
+                                   ((__CHANNEL__) == TIM_CHANNEL_2)   ||   \
+                                   ((__CHANNEL__) == TIM_CHANNEL_3)   ||   \
+                                   ((__CHANNEL__) == TIM_CHANNEL_4))) ||   \
+   (((__INSTANCE__) == TIM21) &&  (((__CHANNEL__) == TIM_CHANNEL_1)   ||   \
+                                   ((__CHANNEL__) == TIM_CHANNEL_2))) ||   \
+   (((__INSTANCE__) == TIM22) &&  (((__CHANNEL__) == TIM_CHANNEL_1)   ||   \
+                                   ((__CHANNEL__) == TIM_CHANNEL_2))))
+
+#elif defined(TIM22)
+
+#define IS_TIM_REMAP(__INSTANCE__, __TIM_REMAP__)               \
+  ((((__INSTANCE__) == TIM2)   &&  ((__TIM_REMAP__) <=  (TIM2_OR_TI4_RMP  | TIM2_OR_ETR_RMP))) || \
+   (((__INSTANCE__) == TIM22)  &&  ((__TIM_REMAP__) <=  (TIM22_OR_TI1_RMP | TIM22_OR_ETR_RMP))) || \
+   (((__INSTANCE__) == TIM21)  &&  ((__TIM_REMAP__) <=  (TIM21_OR_ETR_RMP | TIM21_OR_TI1_RMP | TIM21_OR_TI2_RMP))))
+
+#define IS_CHANNEL_AVAILABLE(__INSTANCE__, __CHANNEL__)     \
+  ((((__INSTANCE__) == TIM2)  &&   (((__CHANNEL__) == TIM_CHANNEL_1)   || \
+                                    ((__CHANNEL__) == TIM_CHANNEL_2)   || \
+                                    ((__CHANNEL__) == TIM_CHANNEL_3)   || \
+                                    ((__CHANNEL__) == TIM_CHANNEL_4))) || \
+   (((__INSTANCE__) == TIM21)  &&  (((__CHANNEL__) == TIM_CHANNEL_1)   || \
+                                    ((__CHANNEL__) == TIM_CHANNEL_2))) || \
+   (((__INSTANCE__) == TIM22)  &&  (((__CHANNEL__) == TIM_CHANNEL_1)   || \
+                                    ((__CHANNEL__) == TIM_CHANNEL_2))))
+#else
+
+#define IS_TIM_REMAP(__INSTANCE__, __TIM_REMAP__)               \
+  ((((__INSTANCE__) == TIM2)   &&  ((__TIM_REMAP__) <=  (TIM2_OR_TI4_RMP  | TIM2_OR_ETR_RMP))) || \
+   (((__INSTANCE__) == TIM21)  &&  ((__TIM_REMAP__) <=  (TIM21_OR_ETR_RMP | TIM21_OR_TI1_RMP | TIM21_OR_TI2_RMP))))
+
+#define IS_CHANNEL_AVAILABLE(__INSTANCE__, __CHANNEL__)     \
+  ((((__INSTANCE__) == TIM2)  &&   (((__CHANNEL__) == TIM_CHANNEL_1)   || \
+                                    ((__CHANNEL__) == TIM_CHANNEL_2)   || \
+                                    ((__CHANNEL__) == TIM_CHANNEL_3)   || \
+                                    ((__CHANNEL__) == TIM_CHANNEL_4))) || \
+   (((__INSTANCE__) == TIM21)  &&  (((__CHANNEL__) == TIM_CHANNEL_1)   || \
+                                    ((__CHANNEL__) == TIM_CHANNEL_2))))
+#endif /* TIM3 && TIM22 */
+
+/**
+  * @}
+  */
+/* End of private macro ------------------------------------------------------*/
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup TIMEx_Exported_Functions TIM Extended Exported Functions
+  * @{
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group5 Extended Peripheral Control functions
+  *  @brief    Peripheral Control functions
+  * @{
+  */
+/* Extended Control functions  ************************************************/
+HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim,
+                                                        TIM_MasterConfigTypeDef *sMasterConfig);
+HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef *htim, uint32_t Remap);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* End of exported functions -------------------------------------------------*/
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* STM32L0xx_HAL_TIM_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_uart_ex.h

@@ -0,0 +1,453 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_uart_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of UART HAL Extended module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32L0xx_HAL_UART_EX_H
+#define STM32L0xx_HAL_UART_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup UARTEx
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup UARTEx_Exported_Types UARTEx Exported Types
+  * @{
+  */
+
+/**
+  * @brief  UART wake up from stop mode parameters
+  */
+typedef struct
+{
+  uint32_t WakeUpEvent;        /*!< Specifies which event will activate the Wakeup from Stop mode flag (WUF).
+                                    This parameter can be a value of @ref UART_WakeUp_from_Stop_Selection.
+                                    If set to UART_WAKEUP_ON_ADDRESS, the two other fields below must
+                                    be filled up. */
+
+  uint16_t AddressLength;      /*!< Specifies whether the address is 4 or 7-bit long.
+                                    This parameter can be a value of @ref UARTEx_WakeUp_Address_Length.  */
+
+  uint8_t Address;             /*!< UART/USART node address (7-bit long max). */
+} UART_WakeUpTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup UARTEx_Exported_Constants UARTEx Exported Constants
+  * @{
+  */
+
+/** @defgroup UARTEx_Word_Length UARTEx Word Length
+  * @{
+  */
+#define UART_WORDLENGTH_7B          USART_CR1_M1   /*!< 7-bit long UART frame */
+#define UART_WORDLENGTH_8B          0x00000000U    /*!< 8-bit long UART frame */
+#define UART_WORDLENGTH_9B          USART_CR1_M0   /*!< 9-bit long UART frame */
+/**
+  * @}
+  */
+
+/** @defgroup UARTEx_WakeUp_Address_Length UARTEx WakeUp Address Length
+  * @{
+  */
+#define UART_ADDRESS_DETECT_4B      0x00000000U      /*!< 4-bit long wake-up address */
+#define UART_ADDRESS_DETECT_7B      USART_CR2_ADDM7  /*!< 7-bit long wake-up address */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup UARTEx_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup UARTEx_Exported_Functions_Group1
+  * @{
+  */
+
+/* Initialization and de-initialization functions  ****************************/
+HAL_StatusTypeDef HAL_RS485Ex_Init(UART_HandleTypeDef *huart, uint32_t Polarity, uint32_t AssertionTime,
+                                   uint32_t DeassertionTime);
+
+/**
+  * @}
+  */
+
+/** @addtogroup UARTEx_Exported_Functions_Group2
+  * @{
+  */
+
+void HAL_UARTEx_WakeupCallback(UART_HandleTypeDef *huart);
+
+/**
+  * @}
+  */
+
+/** @addtogroup UARTEx_Exported_Functions_Group3
+  * @{
+  */
+
+/* Peripheral Control functions  **********************************************/
+HAL_StatusTypeDef HAL_UARTEx_StopModeWakeUpSourceConfig(UART_HandleTypeDef *huart, UART_WakeUpTypeDef WakeUpSelection);
+HAL_StatusTypeDef HAL_UARTEx_EnableStopMode(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UARTEx_DisableStopMode(UART_HandleTypeDef *huart);
+
+HAL_StatusTypeDef HAL_UARTEx_EnableClockStopMode(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UARTEx_DisableClockStopMode(UART_HandleTypeDef *huart);
+
+HAL_StatusTypeDef HAL_MultiProcessorEx_AddressLength_Set(UART_HandleTypeDef *huart, uint32_t AddressLength);
+
+
+HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint16_t *RxLen,
+                                           uint32_t Timeout);
+HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup UARTEx_Private_Macros UARTEx Private Macros
+  * @{
+  */
+
+/** @brief  Report the UART clock source.
+  * @param  __HANDLE__ specifies the UART Handle.
+  * @param  __CLOCKSOURCE__ output variable.
+  * @retval UART clocking source, written in __CLOCKSOURCE__.
+  */
+#if defined (STM32L031xx) || defined (STM32L041xx) || defined (STM32L011xx) || defined (STM32L021xx) || defined (STM32L010xB) || defined (STM32L010x8) || defined (STM32L010x6) || defined (STM32L010x4)
+#define UART_GETCLOCKSOURCE(__HANDLE__,__CLOCKSOURCE__)       \
+  do {                                                        \
+    if((__HANDLE__)->Instance == USART2)                      \
+    {                                                         \
+      switch(__HAL_RCC_GET_USART2_SOURCE())                   \
+      {                                                       \
+        case RCC_USART2CLKSOURCE_PCLK1:                       \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_PCLK1;         \
+          break;                                              \
+        case RCC_USART2CLKSOURCE_HSI:                         \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_HSI;           \
+          break;                                              \
+        case RCC_USART2CLKSOURCE_SYSCLK:                      \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_SYSCLK;        \
+          break;                                              \
+        case RCC_USART2CLKSOURCE_LSE:                         \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_LSE;           \
+          break;                                              \
+        default:                                              \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;     \
+          break;                                              \
+      }                                                       \
+    }                                                         \
+    else if((__HANDLE__)->Instance == LPUART1)                \
+    {                                                         \
+      switch(__HAL_RCC_GET_LPUART1_SOURCE())                  \
+      {                                                       \
+        case RCC_LPUART1CLKSOURCE_PCLK1:                      \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_PCLK1;         \
+          break;                                              \
+        case RCC_LPUART1CLKSOURCE_HSI:                        \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_HSI;           \
+          break;                                              \
+        case RCC_LPUART1CLKSOURCE_SYSCLK:                     \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_SYSCLK;        \
+          break;                                              \
+        case RCC_LPUART1CLKSOURCE_LSE:                        \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_LSE;           \
+          break;                                              \
+        default:                                              \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;     \
+          break;                                              \
+      }                                                       \
+    }                                                         \
+    else                                                      \
+    {                                                         \
+      (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;         \
+    }                                                         \
+  } while(0)
+
+#elif defined (STM32L051xx) || defined (STM32L052xx) || defined (STM32L053xx) || defined (STM32L062xx) || defined (STM32L063xx)
+
+#define UART_GETCLOCKSOURCE(__HANDLE__,__CLOCKSOURCE__)       \
+  do {                                                        \
+    if((__HANDLE__)->Instance == USART1)                      \
+    {                                                         \
+      switch(__HAL_RCC_GET_USART1_SOURCE())                   \
+      {                                                       \
+        case RCC_USART1CLKSOURCE_PCLK2:                       \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_PCLK2;         \
+          break;                                              \
+        case RCC_USART1CLKSOURCE_HSI:                         \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_HSI;           \
+          break;                                              \
+        case RCC_USART1CLKSOURCE_SYSCLK:                      \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_SYSCLK;        \
+          break;                                              \
+        case RCC_USART1CLKSOURCE_LSE:                         \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_LSE;           \
+          break;                                              \
+        default:                                              \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;     \
+          break;                                              \
+      }                                                       \
+    }                                                         \
+    else if((__HANDLE__)->Instance == USART2)                 \
+    {                                                         \
+      switch(__HAL_RCC_GET_USART2_SOURCE())                   \
+      {                                                       \
+        case RCC_USART2CLKSOURCE_PCLK1:                       \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_PCLK1;         \
+          break;                                              \
+        case RCC_USART2CLKSOURCE_HSI:                         \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_HSI;           \
+          break;                                              \
+        case RCC_USART2CLKSOURCE_SYSCLK:                      \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_SYSCLK;        \
+          break;                                              \
+        case RCC_USART2CLKSOURCE_LSE:                         \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_LSE;           \
+          break;                                              \
+        default:                                              \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;     \
+          break;                                              \
+      }                                                       \
+    }                                                         \
+    else if((__HANDLE__)->Instance == LPUART1)                \
+    {                                                         \
+      switch(__HAL_RCC_GET_LPUART1_SOURCE())                  \
+      {                                                       \
+        case RCC_LPUART1CLKSOURCE_PCLK1:                      \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_PCLK1;         \
+          break;                                              \
+        case RCC_LPUART1CLKSOURCE_HSI:                        \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_HSI;           \
+          break;                                              \
+        case RCC_LPUART1CLKSOURCE_SYSCLK:                     \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_SYSCLK;        \
+          break;                                              \
+        case RCC_LPUART1CLKSOURCE_LSE:                        \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_LSE;           \
+          break;                                              \
+        default:                                              \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;     \
+          break;                                              \
+      }                                                       \
+    }                                                         \
+    else                                                      \
+    {                                                         \
+      (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;         \
+    }                                                         \
+  } while(0)
+
+#else
+
+#define UART_GETCLOCKSOURCE(__HANDLE__,__CLOCKSOURCE__)       \
+  do {                                                        \
+    if((__HANDLE__)->Instance == USART1)                      \
+    {                                                         \
+      switch(__HAL_RCC_GET_USART1_SOURCE())                   \
+      {                                                       \
+        case RCC_USART1CLKSOURCE_PCLK2:                       \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_PCLK2;         \
+          break;                                              \
+        case RCC_USART1CLKSOURCE_HSI:                         \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_HSI;           \
+          break;                                              \
+        case RCC_USART1CLKSOURCE_SYSCLK:                      \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_SYSCLK;        \
+          break;                                              \
+        case RCC_USART1CLKSOURCE_LSE:                         \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_LSE;           \
+          break;                                              \
+        default:                                              \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;     \
+          break;                                              \
+      }                                                       \
+    }                                                         \
+    else if((__HANDLE__)->Instance == USART2)                 \
+    {                                                         \
+      switch(__HAL_RCC_GET_USART2_SOURCE())                   \
+      {                                                       \
+        case RCC_USART2CLKSOURCE_PCLK1:                       \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_PCLK1;         \
+          break;                                              \
+        case RCC_USART2CLKSOURCE_HSI:                         \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_HSI;           \
+          break;                                              \
+        case RCC_USART2CLKSOURCE_SYSCLK:                      \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_SYSCLK;        \
+          break;                                              \
+        case RCC_USART2CLKSOURCE_LSE:                         \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_LSE;           \
+          break;                                              \
+        default:                                              \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;     \
+          break;                                              \
+      }                                                       \
+    }                                                         \
+    else if((__HANDLE__)->Instance == USART4)                 \
+    {                                                         \
+      (__CLOCKSOURCE__) = UART_CLOCKSOURCE_PCLK1;             \
+    }                                                         \
+    else if((__HANDLE__)->Instance == USART5)                 \
+    {                                                         \
+      (__CLOCKSOURCE__) = UART_CLOCKSOURCE_PCLK1;             \
+    }                                                         \
+    else if((__HANDLE__)->Instance == LPUART1)                \
+    {                                                         \
+      switch(__HAL_RCC_GET_LPUART1_SOURCE())                  \
+      {                                                       \
+        case RCC_LPUART1CLKSOURCE_PCLK1:                      \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_PCLK1;         \
+          break;                                              \
+        case RCC_LPUART1CLKSOURCE_HSI:                        \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_HSI;           \
+          break;                                              \
+        case RCC_LPUART1CLKSOURCE_SYSCLK:                     \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_SYSCLK;        \
+          break;                                              \
+        case RCC_LPUART1CLKSOURCE_LSE:                        \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_LSE;           \
+          break;                                              \
+        default:                                              \
+          (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;     \
+          break;                                              \
+      }                                                       \
+    }                                                         \
+    else                                                      \
+    {                                                         \
+      (__CLOCKSOURCE__) = UART_CLOCKSOURCE_UNDEFINED;         \
+    }                                                         \
+  } while(0)
+#endif /* (STM32L031xx) || (STM32L041xx) || (STM32L011xx) || (STM32L021xx) || (STM32L010xB) || (STM32L010x8) || (STM32L010x6) || (STM32L010x4)*/
+
+
+/** @brief  Report the UART mask to apply to retrieve the received data
+  *         according to the word length and to the parity bits activation.
+  * @note   If PCE = 1, the parity bit is not included in the data extracted
+  *         by the reception API().
+  *         This masking operation is not carried out in the case of
+  *         DMA transfers.
+  * @param  __HANDLE__ specifies the UART Handle.
+  * @retval None, the mask to apply to UART RDR register is stored in (__HANDLE__)->Mask field.
+  */
+#define UART_MASK_COMPUTATION(__HANDLE__)                             \
+  do {                                                                \
+    if ((__HANDLE__)->Init.WordLength == UART_WORDLENGTH_9B)          \
+    {                                                                 \
+      if ((__HANDLE__)->Init.Parity == UART_PARITY_NONE)              \
+      {                                                               \
+        (__HANDLE__)->Mask = 0x01FFU ;                                \
+      }                                                               \
+      else                                                            \
+      {                                                               \
+        (__HANDLE__)->Mask = 0x00FFU ;                                \
+      }                                                               \
+    }                                                                 \
+    else if ((__HANDLE__)->Init.WordLength == UART_WORDLENGTH_8B)     \
+    {                                                                 \
+      if ((__HANDLE__)->Init.Parity == UART_PARITY_NONE)              \
+      {                                                               \
+        (__HANDLE__)->Mask = 0x00FFU ;                                \
+      }                                                               \
+      else                                                            \
+      {                                                               \
+        (__HANDLE__)->Mask = 0x007FU ;                                \
+      }                                                               \
+    }                                                                 \
+    else if ((__HANDLE__)->Init.WordLength == UART_WORDLENGTH_7B)     \
+    {                                                                 \
+      if ((__HANDLE__)->Init.Parity == UART_PARITY_NONE)              \
+      {                                                               \
+        (__HANDLE__)->Mask = 0x007FU ;                                \
+      }                                                               \
+      else                                                            \
+      {                                                               \
+        (__HANDLE__)->Mask = 0x003FU ;                                \
+      }                                                               \
+    }                                                                 \
+    else                                                              \
+    {                                                                 \
+      (__HANDLE__)->Mask = 0x0000U;                                   \
+    }                                                                 \
+  } while(0U)
+
+/**
+  * @brief Ensure that UART frame length is valid.
+  * @param __LENGTH__ UART frame length.
+  * @retval SET (__LENGTH__ is valid) or RESET (__LENGTH__ is invalid)
+  */
+#define IS_UART_WORD_LENGTH(__LENGTH__) (((__LENGTH__) == UART_WORDLENGTH_7B) || \
+                                         ((__LENGTH__) == UART_WORDLENGTH_8B) || \
+                                         ((__LENGTH__) == UART_WORDLENGTH_9B))
+
+/**
+  * @brief Ensure that UART wake-up address length is valid.
+  * @param __ADDRESS__ UART wake-up address length.
+  * @retval SET (__ADDRESS__ is valid) or RESET (__ADDRESS__ is invalid)
+  */
+#define IS_UART_ADDRESSLENGTH_DETECT(__ADDRESS__) (((__ADDRESS__) == UART_ADDRESS_DETECT_4B) || \
+                                                   ((__ADDRESS__) == UART_ADDRESS_DETECT_7B))
+
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32L0xx_HAL_UART_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal.c

@@ -0,0 +1,674 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal.c
+  * @author  MCD Application Team
+  * @brief   HAL module driver.
+  *          This is the common part of the HAL initialization
+  *
+  @verbatim
+  ==============================================================================
+                     ##### How to use this driver #####
+  ==============================================================================
+    [..]
+    The common HAL driver contains a set of generic and common APIs that can be
+    used by the PPP peripheral drivers and the user to start using the HAL.
+    [..]
+    The HAL contains two APIs categories:
+         (+) Common HAL APIs
+         (+) Services HAL APIs
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+#ifdef HAL_MODULE_ENABLED
+
+/** @addtogroup HAL
+  * @brief HAL module driver.
+  * @{
+  */
+
+/** @addtogroup HAL_Exported_Constants
+  * @{
+  */
+
+/** @defgroup HAL_Version HAL Version
+  * @{
+  */
+
+/**
+ * @brief STM32L0xx HAL Driver version number
+ */
+#define __STM32L0xx_HAL_VERSION_MAIN   (0x01U) /*!< [31:24] main version */
+#define __STM32L0xx_HAL_VERSION_SUB1   (0x0AU) /*!< [23:16] sub1 version */
+#define __STM32L0xx_HAL_VERSION_SUB2   (0x05U) /*!< [15:8]  sub2 version */
+#define __STM32L0xx_HAL_VERSION_RC     (0x00U) /*!< [7:0]  release candidate */
+#define __STM32L0xx_HAL_VERSION         ((__STM32L0xx_HAL_VERSION_MAIN << 24U)\
+                                        |(__STM32L0xx_HAL_VERSION_SUB1 << 16U)\
+                                        |(__STM32L0xx_HAL_VERSION_SUB2 << 8U )\
+                                        |(__STM32L0xx_HAL_VERSION_RC))
+
+#define IDCODE_DEVID_MASK    (0x00000FFFU)
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported variables --------------------------------------------------------*/
+/** @addtogroup HAL_Exported_Variables
+  * @{
+  */
+__IO uint32_t uwTick;
+uint32_t uwTickPrio   = (1UL << __NVIC_PRIO_BITS); /* Invalid PRIO */
+HAL_TickFreqTypeDef uwTickFreq = HAL_TICK_FREQ_DEFAULT;  /* 1KHz */
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup HAL_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup HAL_Exported_Functions_Group1
+ *  @brief    Initialization and de-initialization functions
+ *
+@verbatim
+ ===============================================================================
+              ##### Initialization and de-initialization functions #####
+ ===============================================================================
+   [..]  This section provides functions allowing to:
+      (+) Initialize the Flash interface, the NVIC allocation and initial clock
+          configuration. It initializes the source of time base also when timeout
+          is needed and the backup domain when enabled.
+      (+) De-initialize common part of the HAL.
+      (+) Configure the time base source to have 1ms time base with a dedicated
+          Tick interrupt priority.
+        (++) SysTick timer is used by default as source of time base, but user
+             can eventually implement his proper time base source (a general purpose
+             timer for example or other time source), keeping in mind that Time base
+             duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
+             handled in milliseconds basis.
+        (++) Time base configuration function (HAL_InitTick ()) is called automatically
+             at the beginning of the program after reset by HAL_Init() or at any time
+             when clock is configured, by HAL_RCC_ClockConfig().
+        (++) Source of time base is configured  to generate interrupts at regular
+             time intervals. Care must be taken if HAL_Delay() is called from a
+             peripheral ISR process, the Tick interrupt line must have higher priority
+            (numerically lower) than the peripheral interrupt. Otherwise the caller
+            ISR process will be blocked.
+       (++) functions affecting time base configurations are declared as __weak
+             to make  override possible  in case of other  implementations in user file.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief This function configures the Flash prefetch, Flash preread and Buffer cache,
+  *        Configures time base source, NVIC and Low level hardware
+  * @note This function is called at the beginning of program after reset and before
+  *       the clock configuration
+  * @note The time base configuration is based on MSI clock when exiting from Reset.
+  *       Once done, time base tick start incrementing.
+  *        In the default implementation,Systick is used as source of time base.
+  *        the tick variable is incremented each 1ms in its ISR.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_Init(void)
+{
+  HAL_StatusTypeDef  status = HAL_OK;
+
+  /* Configure Buffer cache, Flash prefetch,  Flash preread */
+#if (BUFFER_CACHE_DISABLE != 0)
+  __HAL_FLASH_BUFFER_CACHE_DISABLE();
+#endif /* BUFFER_CACHE_DISABLE */
+
+#if (PREREAD_ENABLE != 0)
+  __HAL_FLASH_PREREAD_BUFFER_ENABLE();
+#endif /* PREREAD_ENABLE */
+
+#if (PREFETCH_ENABLE != 0)
+  __HAL_FLASH_PREFETCH_BUFFER_ENABLE();
+#endif /* PREFETCH_ENABLE */
+
+  /* Use SysTick as time base source and configure 1ms tick (default clock after Reset is MSI) */
+  if (HAL_InitTick(TICK_INT_PRIORITY) != HAL_OK)
+  {
+    status = HAL_ERROR;
+  }
+  else
+  {
+    /* Init the low level hardware */
+    HAL_MspInit();
+  }
+
+  /* Return function status */
+  return status;
+}
+
+/**
+  * @brief This function de-initializes common part of the HAL and stops the source
+  *        of time base.
+  * @note This function is optional.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DeInit(void)
+{
+  /* Reset of all peripherals */
+  __HAL_RCC_APB1_FORCE_RESET();
+  __HAL_RCC_APB1_RELEASE_RESET();
+
+  __HAL_RCC_APB2_FORCE_RESET();
+  __HAL_RCC_APB2_RELEASE_RESET();
+
+  __HAL_RCC_AHB_FORCE_RESET();
+  __HAL_RCC_AHB_RELEASE_RESET();
+
+  __HAL_RCC_IOP_FORCE_RESET();
+  __HAL_RCC_IOP_RELEASE_RESET();
+
+  /* De-Init the low level hardware */
+  HAL_MspDeInit();
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Initializes the MSP.
+  * @retval None
+  */
+__weak void HAL_MspInit(void)
+{
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_MspInit could be implemented in the user file
+   */
+}
+
+/**
+  * @brief  DeInitializes the MSP.
+  * @retval None
+  */
+__weak void HAL_MspDeInit(void)
+{
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_MspDeInit could be implemented in the user file
+   */
+}
+
+/**
+  * @brief This function configures the source of the time base:
+  *        The time source is configured  to have 1ms time base with a dedicated 
+  *        Tick interrupt priority.
+  * @note This function is called  automatically at the beginning of program after
+  *       reset by HAL_Init() or at any time when clock is reconfigured  by HAL_RCC_ClockConfig().
+  * @note In the default implementation, SysTick timer is the source of time base. 
+  *       It is used to generate interrupts at regular time intervals. 
+  *       Care must be taken if HAL_Delay() is called from a peripheral ISR process, 
+  *       The SysTick interrupt must have higher priority (numerically lower)
+  *       than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
+  *       The function is declared as __weak  to be overwritten  in case of other
+  *       implementation  in user file.
+  * @param TickPriority Tick interrupt priority.
+  * @retval HAL status
+  */
+__weak HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority)
+{
+  /* Configure the SysTick to have interrupt in 1ms time basis*/
+  if (HAL_SYSTICK_Config(SystemCoreClock / (1000U / uwTickFreq)) > 0U)
+  {
+    return HAL_ERROR;
+  }
+
+  /* Configure the SysTick IRQ priority */
+  if (TickPriority < (1UL << __NVIC_PRIO_BITS))
+  {
+    HAL_NVIC_SetPriority(SysTick_IRQn, TickPriority, 0U);
+    uwTickPrio = TickPriority;
+  }
+  else
+  {
+    return HAL_ERROR;
+  }
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/** @addtogroup HAL_Exported_Functions_Group2
+ *  @brief    HAL Control functions
+ *
+@verbatim
+ ===============================================================================
+                      ##### HAL Control functions #####
+ ===============================================================================
+    [..]  This section provides functions allowing to:
+      (+) Provide a tick value in millisecond
+      (+) Provide a blocking delay in millisecond
+      (+) Suspend the time base source interrupt
+      (+) Resume the time base source interrupt
+      (+) Get the HAL API driver version
+      (+) Get the device identifier
+      (+) Get the device revision identifier
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief This function is called to increment a global variable "uwTick"
+  *        used as application time base.
+  * @note In the default implementation, this variable is incremented each 1ms
+  *       in SysTick ISR.
+ * @note This function is declared as __weak to be overwritten in case of other
+  *      implementations in user file.
+  * @retval None
+  */
+__weak void HAL_IncTick(void)
+{
+  uwTick += uwTickFreq;
+}
+
+/**
+  * @brief Provides a tick value in millisecond.
+  * @note This function is declared as __weak to be overwritten in case of other
+  *       implementations in user file.
+  * @retval tick value
+  */
+__weak uint32_t HAL_GetTick(void)
+{
+  return uwTick;
+}
+
+/**
+  * @brief This function returns a tick priority.
+  * @retval tick priority
+  */
+uint32_t HAL_GetTickPrio(void)
+{
+  return uwTickPrio;
+}
+
+/**
+  * @brief Set new tick Freq.
+  * @retval Status
+  */
+HAL_StatusTypeDef HAL_SetTickFreq(HAL_TickFreqTypeDef Freq)
+{
+  HAL_StatusTypeDef status  = HAL_OK;
+  HAL_TickFreqTypeDef prevTickFreq;
+
+  assert_param(IS_TICKFREQ(Freq));
+
+  if (uwTickFreq != Freq)
+  {
+    /* Back up uwTickFreq frequency */
+    prevTickFreq = uwTickFreq;
+
+    /* Update uwTickFreq global variable used by HAL_InitTick() */
+    uwTickFreq = Freq;
+
+    /* Apply the new tick Freq  */
+    status = HAL_InitTick(uwTickPrio);
+
+    if (status != HAL_OK)
+    {
+      /* Restore previous tick frequency */
+      uwTickFreq = prevTickFreq;
+    }
+  }
+
+  return status;
+}
+
+/**
+  * @brief Return tick frequency.
+  * @retval tick period in Hz
+  */
+HAL_TickFreqTypeDef HAL_GetTickFreq(void)
+{
+  return uwTickFreq;
+}
+
+/**
+  * @brief This function provides minimum delay (in milliseconds) based
+  *        on variable incremented.
+  * @note In the default implementation , SysTick timer is the source of time base.
+  *       It is used to generate interrupts at regular time intervals where uwTick
+  *       is incremented.
+  * @note This function is declared as __weak to be overwritten in case of other
+  *       implementations in user file.
+  * @param Delay specifies the delay time length, in milliseconds.
+  * @retval None
+  */
+__weak void HAL_Delay(uint32_t Delay)
+{
+  uint32_t tickstart = HAL_GetTick();
+  uint32_t wait = Delay;
+
+  /* Add a freq to guarantee minimum wait */
+  if (wait < HAL_MAX_DELAY)
+  {
+    wait += (uint32_t)(uwTickFreq);
+  }
+
+  while((HAL_GetTick() - tickstart) < wait)
+  {
+  }
+}
+
+/**
+  * @brief Suspends the Tick increment.
+  * @note In the default implementation , SysTick timer is the source of time base. It is
+  *       used to generate interrupts at regular time intervals. Once HAL_SuspendTick()
+  *       is called, the SysTick interrupt will be disabled and so Tick increment
+  *       is suspended.
+  * @note This function is declared as __weak to be overwritten in case of other
+  *       implementations in user file.
+  * @retval None
+  */
+__weak void HAL_SuspendTick(void)
+{
+  /* Disable SysTick Interrupt */
+  SysTick->CTRL &= ~SysTick_CTRL_TICKINT_Msk;
+}
+
+/**
+  * @brief Resumes the Tick increment.
+  * @note In the default implementation , SysTick timer is the source of time base. It is
+  *       used to generate interrupts at regular time intervals. Once HAL_ResumeTick()
+  *       is called, the SysTick interrupt will be enabled and so Tick increment
+  *       is resumed.
+  * @note This function is declared as __weak to be overwritten in case of other
+  *       implementations in user file.
+  * @retval None
+  */
+__weak void HAL_ResumeTick(void)
+{
+  /* Enable SysTick Interrupt */
+  SysTick->CTRL  |= SysTick_CTRL_TICKINT_Msk;
+}
+
+/**
+  * @brief Returns the HAL revision
+  * @retval version: 0xXYZR (8bits for each decimal, R for RC)
+  */
+uint32_t HAL_GetHalVersion(void)
+{
+  return __STM32L0xx_HAL_VERSION;
+}
+
+/**
+  * @brief Returns the device revision identifier.
+  * @retval Device revision identifier
+  */
+uint32_t HAL_GetREVID(void)
+{
+  return((DBGMCU->IDCODE) >> 16U);
+}
+
+/**
+  * @brief  Returns the device identifier.
+  * @retval Device identifier
+  */
+uint32_t HAL_GetDEVID(void)
+{
+   return((DBGMCU->IDCODE) & IDCODE_DEVID_MASK);
+}
+
+/**
+  * @brief  Returns the first word of the unique device identifier (UID based on 96 bits)
+  * @retval Device identifier
+  */
+uint32_t HAL_GetUIDw0(void)
+{
+  return(READ_REG(*((uint32_t *)UID_BASE)));
+}
+
+/**
+  * @brief  Returns the second word of the unique device identifier (UID based on 96 bits)
+  * @retval Device identifier
+  */
+uint32_t HAL_GetUIDw1(void)
+{
+  return(READ_REG(*((uint32_t *)(UID_BASE + 0x04U))));
+}
+
+/**
+  * @brief  Returns the third word of the unique device identifier (UID based on 96 bits)
+  * @retval Device identifier
+  */
+uint32_t HAL_GetUIDw2(void)
+{
+  return(READ_REG(*((uint32_t *)(UID_BASE + 0x14U))));
+}
+
+/**
+  * @}
+  */
+
+/** @addtogroup HAL_Exported_Functions_Group2
+ *  @brief    HAL Debug functions
+ *
+@verbatim
+ ===============================================================================
+                      ##### HAL Debug functions #####
+ ===============================================================================
+    [..]  This section provides functions allowing to:
+      (+) Enable/Disable Debug module during SLEEP mode
+      (+) Enable/Disable Debug module during STOP mode
+      (+) Enable/Disable Debug module during STANDBY mode
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Enables the Debug Module during SLEEP mode
+  * @retval None
+  */
+void HAL_DBGMCU_EnableDBGSleepMode(void)
+{
+  SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_SLEEP);
+}
+
+/**
+  * @brief  Disables the Debug Module during SLEEP mode
+  * @retval None
+  */
+void HAL_DBGMCU_DisableDBGSleepMode(void)
+{
+  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_SLEEP);
+}
+
+/**
+  * @brief  Enables the Debug Module during STOP mode
+  * @retval None
+  */
+void HAL_DBGMCU_EnableDBGStopMode(void)
+{
+  SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STOP);
+}
+
+/**
+  * @brief  Disables the Debug Module during STOP mode
+  * @retval None
+  */
+void HAL_DBGMCU_DisableDBGStopMode(void)
+{
+  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STOP);
+}
+
+/**
+  * @brief  Enables the Debug Module during STANDBY mode
+  * @retval None
+  */
+void HAL_DBGMCU_EnableDBGStandbyMode(void)
+{
+  SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY);
+}
+
+/**
+  * @brief  Disables the Debug Module during STANDBY mode
+  * @retval None
+  */
+void HAL_DBGMCU_DisableDBGStandbyMode(void)
+{
+  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY);
+}
+
+/**
+  * @brief  Enable low power mode behavior when the MCU is in Debug mode.
+  * @param Periph: specifies the low power mode.
+  *   This parameter can be any combination of the following values:
+  *     @arg DBGMCU_SLEEP: Keep debugger connection during SLEEP mode
+  *     @arg DBGMCU_STOP: Keep debugger connection during STOP mode
+  *     @arg DBGMCU_STANDBY: Keep debugger connection during STANDBY mode
+  * @retval None
+  */
+void HAL_DBGMCU_DBG_EnableLowPowerConfig(uint32_t Periph)
+{
+  /* Check the parameters */
+  assert_param(IS_DBGMCU_PERIPH(Periph));
+
+  DBGMCU->CR |= Periph;
+
+}
+/**
+  * @brief  Disable low power mode behavior when the MCU is in Debug mode.
+  * @param Periph: specifies the low power mode.
+  *   This parameter can be any combination of the following values:
+  *     @arg DBGMCU_SLEEP: Keep debugger connection during SLEEP mode
+  *     @arg DBGMCU_STOP: Keep debugger connection during STOP mode
+  *     @arg DBGMCU_STANDBY: Keep debugger connection during STANDBY mode
+  * @retval None
+  */
+void HAL_DBGMCU_DBG_DisableLowPowerConfig(uint32_t Periph)
+{
+  /* Check the parameters */
+  assert_param(IS_DBGMCU_PERIPH(Periph));
+  {
+    DBGMCU->CR &= ~Periph;
+  }
+}
+
+/**
+  * @}
+  */
+
+/** @addtogroup HAL_Exported_Functions_Group3
+ *  @brief    HAL SYSCFG configuration functions
+ *
+@verbatim
+ ===============================================================================
+                      ##### HAL SYSCFG configuration functions #####
+ ===============================================================================
+    [..]  This section provides functions allowing to:
+      (+) Return the boot mode
+      (+) Select the output of internal reference voltage (VREFINT)
+      (+) Lock/Unlock the SYSCFG VREF register values
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Returns the boot mode as configured by user.
+  * @retval The boot mode as configured by user. The returned value can be one
+  *         of the following values:
+  *              - 0x00000000 : Boot is configured in Main Flash memory
+  *              - 0x00000100 : Boot is configured in System Flash memory
+  *              - 0x00000300 : Boot is configured in Embedded SRAM memory
+  */
+uint32_t  HAL_SYSCFG_GetBootMode(void)
+{
+  return (SYSCFG->CFGR1 & SYSCFG_CFGR1_BOOT_MODE);
+}
+
+/**
+  * @brief Selects the output of internal reference voltage (VREFINT).
+  *        The VREFINT output can be routed to(PB0) or
+  *        (PB1) or both.
+  * @param SYSCFG_Vrefint_OUTPUT: new state of the Vrefint output.
+  *        This parameter can be one of the following values:
+  *     @arg SYSCFG_VREFINT_OUT_NONE
+  *     @arg SYSCFG_VREFINT_OUT_PB0
+  *     @arg SYSCFG_VREFINT_OUT_PB1
+  *     @arg SYSCFG_VREFINT_OUT_PB0_PB1
+  * @retval None
+  */
+void HAL_SYSCFG_VREFINT_OutputSelect(uint32_t SYSCFG_Vrefint_OUTPUT)
+{
+  /* Check the parameters */
+  assert_param(IS_SYSCFG_VREFINT_OUT_SELECT(SYSCFG_Vrefint_OUTPUT));
+
+  /* Set the output Vrefint pin */
+  SYSCFG->CFGR3 &= ~(SYSCFG_CFGR3_VREF_OUT);
+  SYSCFG->CFGR3 |= (uint32_t)(SYSCFG_Vrefint_OUTPUT);
+}
+
+/**
+  * @brief  Lock the SYSCFG VREF register values
+  * @retval None
+  */
+void HAL_SYSCFG_Enable_Lock_VREFINT(void)
+{
+    /* Enable the LOCK by setting REF_LOCK bit in the CFGR3 register */
+    SET_BIT(SYSCFG->CFGR3, SYSCFG_CFGR3_REF_LOCK);
+}
+
+/**
+  * @brief  Unlock the overall SYSCFG VREF register values
+  * @retval None
+  */
+void HAL_SYSCFG_Disable_Lock_VREFINT(void)
+{
+    /* Disable the LOCK by setting REF_LOCK bit in the CFGR3 register */
+    CLEAR_BIT(SYSCFG->CFGR3, SYSCFG_CFGR3_REF_LOCK);
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+#endif /* HAL_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_cortex.c

@@ -0,0 +1,415 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_cortex.c
+  * @author  MCD Application Team
+  * @brief   CORTEX HAL module driver.
+  *          This file provides firmware functions to manage the following 
+  *          functionalities of the CORTEX:
+  *           + Initialization and Configuration functions
+  *           + Peripheral Control functions 
+  *
+  @verbatim  
+  ==============================================================================
+                        ##### How to use this driver #####
+  ==============================================================================
+    [..]  
+    *** How to configure Interrupts using CORTEX HAL driver ***
+    ===========================================================
+    [..]     
+    This section provides functions allowing to configure the NVIC interrupts (IRQ).
+    The Cortex M0+ exceptions are managed by CMSIS functions.
+      (#) Enable and Configure the priority of the selected IRQ Channels. 
+             The priority can be 0..3. 
+
+        -@- Lower priority values gives higher priority.
+        -@- Priority Order:
+            (#@) Lowest priority.
+            (#@) Lowest hardware priority (IRQn position).  
+    
+     (#)  Configure the priority of the selected IRQ Channels using HAL_NVIC_SetPriority() 
+
+     (#)  Enable the selected IRQ Channels using HAL_NVIC_EnableIRQ() 
+      
+    [..]  
+    *** How to configure Systick using CORTEX HAL driver ***
+    ========================================================
+    [..]
+    Setup SysTick Timer for time base.
+           
+   (+) The HAL_SYSTICK_Config()function calls the SysTick_Config() function which
+       is a CMSIS function that:
+        (++) Configures the SysTick Reload register with value passed as function parameter.
+        (++) Configures the SysTick IRQ priority to the lowest value (0x03).
+        (++) Resets the SysTick Counter register.
+        (++) Configures the SysTick Counter clock source to be Core Clock Source (HCLK).
+        (++) Enables the SysTick Interrupt.
+        (++) Starts the SysTick Counter.
+	
+   (+) You can change the SysTick Clock source to be HCLK_Div8 by calling the function
+       HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK_DIV8) just after the
+       HAL_SYSTICK_Config() function call. The HAL_SYSTICK_CLKSourceConfig() function is defined
+       inside the stm32l0xx_hal_cortex.c file.
+
+   (+) You can change the SysTick IRQ priority by calling the
+       HAL_NVIC_SetPriority(SysTick_IRQn,...) function just after the HAL_SYSTICK_Config() function 
+       call. The HAL_NVIC_SetPriority() call the NVIC_SetPriority() function which is a CMSIS function.
+
+   (+) To adjust the SysTick time base, use the following formula:
+                            
+       Reload Value = SysTick Counter Clock (Hz) x  Desired Time base (s)
+       (++) Reload Value is the parameter to be passed for HAL_SYSTICK_Config() function
+       (++) Reload Value should not exceed 0xFFFFFF
+   
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************  
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+
+/** @addtogroup CORTEX
+  * @brief CORTEX HAL module driver
+  * @{
+  */
+
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/* Private macros ------------------------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup CORTEX_Exported_Functions
+  * @{
+  */
+
+
+/** @addtogroup CORTEX_Exported_Functions_Group1 Initialization and de-initialization functions 
+ *  @brief    Initialization and Configuration functions 
+ *
+@verbatim    
+  ==============================================================================
+              ##### Initialization and Configuration functions #####
+  ==============================================================================
+    [..]
+      This section provides the CORTEX HAL driver functions allowing to configure Interrupts
+      Systick functionalities 
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Sets the priority of an interrupt.
+  * @param  IRQn External interrupt number .
+  *         This parameter can be an enumerator of  IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to stm32l0xx.h file)
+  * @param  PreemptPriority The pre-emption priority for the IRQn channel.
+  *         This parameter can be a value between 0 and 3.
+  *         A lower priority value indicates a higher priority 
+  * @param  SubPriority the subpriority level for the IRQ channel.
+  *         with stm32l0xx devices, this parameter is a dummy value and it is ignored, because 
+  *         no subpriority supported in Cortex M0+ based products.   
+  * @retval None
+  */
+void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority)
+{ 
+    /* Check the parameters */
+  assert_param(IS_NVIC_PREEMPTION_PRIORITY(PreemptPriority));
+  NVIC_SetPriority(IRQn,PreemptPriority);
+}
+
+/**
+  * @brief  Enable a device specific interrupt in the NVIC interrupt controller.
+  * @note   To configure interrupts priority correctly, the NVIC_PriorityGroupConfig()
+  *         function should be called before. 
+  * @param  IRQn External interrupt number .
+  *         This parameter can be an enumerator of  IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to stm32l0xx.h file)  
+  * @retval None
+  */
+void HAL_NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
+  
+  /* Enable interrupt */
+  NVIC_EnableIRQ(IRQn);
+}
+
+/**
+  * @brief  Disable a device specific interrupt in the NVIC interrupt controller.
+  * @param  IRQn External interrupt number .
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to stm32l0xx.h file)  
+  * @retval None
+  */
+void HAL_NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+    /* Check the parameters */
+  assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
+  
+  /* Disable interrupt */
+  NVIC_DisableIRQ(IRQn);
+}
+
+/**
+  * @brief  Initiate a system reset request to reset the MCU.
+  * @retval None
+  */
+void HAL_NVIC_SystemReset(void)
+{
+  /* System Reset */
+  NVIC_SystemReset();
+}
+
+/**
+  * @brief  Initialize the System Timer with interrupt enabled and start the System Tick Timer (SysTick)
+  *         Counter is in free running mode to generate periodic interrupts.
+  * @param  TicksNumb Specifies the ticks Number of ticks between two interrupts.
+  * @retval status:  - 0  Function succeeded.
+  *                  - 1  Function failed.
+  */
+uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb)
+{
+   return SysTick_Config(TicksNumb);
+}
+/**
+  * @}
+  */
+
+/** @addtogroup CORTEX_Exported_Functions_Group2 Peripheral Control functions 
+ *  @brief   Cortex control functions 
+ *
+@verbatim   
+  ==============================================================================
+                      ##### Peripheral Control functions #####
+  ==============================================================================  
+    [..]
+      This subsection provides a set of functions allowing to control the CORTEX
+      (NVIC, SYSTICK) functionalities. 
+ 
+      
+@endverbatim
+  * @{
+  */
+
+
+/**
+  * @brief  Gets the priority of an interrupt.
+  * @param  IRQn External interrupt number.
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32l0xxxx.h))
+  * @retval None
+  */
+uint32_t HAL_NVIC_GetPriority(IRQn_Type IRQn)
+{
+  /* Get priority for Cortex-M system or device specific interrupts */
+  return NVIC_GetPriority(IRQn);
+}
+
+/**
+  * @brief  Sets Pending bit of an external interrupt.
+  * @param  IRQn External interrupt number
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to stm32l0xx.h file)  
+  * @retval None
+  */
+void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{ 
+  /* Set interrupt pending */
+  NVIC_SetPendingIRQ(IRQn);
+}
+
+/**
+  * @brief  Get Pending Interrupt (read the pending register in the NVIC 
+  *         and return the pending bit for the specified interrupt).
+  * @param  IRQn External interrupt number .
+  *          This parameter can be an enumerator of  IRQn_Type enumeration
+  *          (For the complete STM32 Devices IRQ Channels list, please refer to stm32l0xx.h file)  
+  * @retval status: - 0  Interrupt status is not pending.
+  *                 - 1  Interrupt status is pending.
+  */
+uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{ 
+  /* Return 1 if pending else 0 */
+  return NVIC_GetPendingIRQ(IRQn);
+}
+
+/**
+  * @brief  Clear the pending bit of an external interrupt.
+  * @param  IRQn External interrupt number .
+  *         This parameter can be an enumerator of IRQn_Type enumeration
+  *         (For the complete STM32 Devices IRQ Channels list, please refer to stm32l0xx.h file)  
+  * @retval None
+  */
+void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{ 
+  /* Clear pending interrupt */
+  NVIC_ClearPendingIRQ(IRQn);
+}
+
+
+/**
+  * @brief  Configure the SysTick clock source.
+  * @param  CLKSource specifies the SysTick clock source.
+  *          This parameter can be one of the following values:
+  *             @arg SYSTICK_CLKSOURCE_HCLK_DIV8: AHB clock divided by 8 selected as SysTick clock source.
+  *             @arg SYSTICK_CLKSOURCE_HCLK: AHB clock selected as SysTick clock source.
+  * @retval None
+  */
+void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource)
+{
+  /* Check the parameters */
+  assert_param(IS_SYSTICK_CLK_SOURCE(CLKSource));
+  if (CLKSource == SYSTICK_CLKSOURCE_HCLK)
+  {
+    SysTick->CTRL |= SYSTICK_CLKSOURCE_HCLK;
+  }
+  else
+  {
+    SysTick->CTRL &= ~SYSTICK_CLKSOURCE_HCLK;
+  }
+}
+
+/**
+  * @brief  Handle SYSTICK interrupt request.
+  * @retval None
+  */
+void HAL_SYSTICK_IRQHandler(void)
+{
+  HAL_SYSTICK_Callback();
+}
+
+/**
+  * @brief  SYSTICK callback.
+  * @retval None
+  */
+__weak void HAL_SYSTICK_Callback(void)
+{
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_SYSTICK_Callback could be implemented in the user file
+   */
+}
+
+#if (__MPU_PRESENT == 1U)
+/**
+  * @brief  Disable the MPU.
+  * @retval None
+  */
+void HAL_MPU_Disable(void)
+{
+
+  /*Data Memory Barrier setup */
+  __DMB();
+  /* Disable the MPU */
+  MPU->CTRL = 0;
+}
+
+/**
+  * @brief  Enable the MPU.
+  * @param  MPU_Control Specifies the control mode of the MPU during hard fault,
+  *          NMI, FAULTMASK and privileged access to the default memory
+  *          This parameter can be one of the following values:
+  *            @arg MPU_HFNMI_PRIVDEF_NONE
+  *            @arg MPU_HARDFAULT_NMI
+  *            @arg MPU_PRIVILEGED_DEFAULT
+  *            @arg MPU_HFNMI_PRIVDEF
+  * @retval None
+  */
+
+void HAL_MPU_Enable(uint32_t MPU_Control)
+{
+  /* Enable the MPU */
+   MPU->CTRL   = MPU_Control | MPU_CTRL_ENABLE_Msk;
+  /* Data Synchronization Barrier setup */
+  __DSB();
+  /* Instruction Synchronization Barrier setup */
+  __ISB();
+
+}
+
+/**
+  * @brief  Initialize and configure the Region and the memory to be protected.
+  * @param  MPU_Init Pointer to a MPU_Region_InitTypeDef structure that contains
+  *                the initialization and configuration information.
+  * @retval None
+  */
+void HAL_MPU_ConfigRegion(MPU_Region_InitTypeDef *MPU_Init)
+{
+  /* Check the parameters */
+  assert_param(IS_MPU_REGION_NUMBER(MPU_Init->Number));
+  assert_param(IS_MPU_REGION_ENABLE(MPU_Init->Enable));
+
+  /* Set the Region number */
+  MPU->RNR = MPU_Init->Number;
+
+  if ((MPU_Init->Enable) == MPU_REGION_ENABLE)
+  {
+    /* Check the parameters */
+    assert_param(IS_MPU_INSTRUCTION_ACCESS(MPU_Init->DisableExec));
+    assert_param(IS_MPU_REGION_PERMISSION_ATTRIBUTE(MPU_Init->AccessPermission));
+    assert_param(IS_MPU_ACCESS_SHAREABLE(MPU_Init->IsShareable));
+    assert_param(IS_MPU_ACCESS_CACHEABLE(MPU_Init->IsCacheable));
+    assert_param(IS_MPU_ACCESS_BUFFERABLE(MPU_Init->IsBufferable));
+    assert_param(IS_MPU_SUB_REGION_DISABLE(MPU_Init->SubRegionDisable));
+    assert_param(IS_MPU_REGION_SIZE(MPU_Init->Size));
+
+    /* Set the base adsress and set the 4 LSB to 0 */
+    MPU->RBAR = (MPU_Init->BaseAddress) & 0xfffffff0U;
+
+    /* Fill the field RASR */
+    MPU->RASR = ((uint32_t)MPU_Init->DisableExec        << MPU_RASR_XN_Pos)   |
+                ((uint32_t)MPU_Init->AccessPermission   << MPU_RASR_AP_Pos)   |
+                ((uint32_t)MPU_Init->IsShareable        << MPU_RASR_S_Pos)    |
+                ((uint32_t)MPU_Init->IsCacheable        << MPU_RASR_C_Pos)    |
+                ((uint32_t)MPU_Init->IsBufferable       << MPU_RASR_B_Pos)    |
+                ((uint32_t)MPU_Init->SubRegionDisable   << MPU_RASR_SRD_Pos)  |
+                ((uint32_t)MPU_Init->Size               << MPU_RASR_SIZE_Pos) |
+                ((uint32_t)MPU_Init->Enable             << MPU_RASR_ENABLE_Pos);
+  }
+  else
+  {
+    MPU->RBAR = 0x00U;
+    MPU->RASR = 0x00U;
+  }
+}
+#endif /* __MPU_PRESENT */
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_dma.c

@@ -0,0 +1,885 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_dma.c
+  * @author  MCD Application Team
+  * @brief   DMA HAL module driver.
+  *         This file provides firmware functions to manage the following
+  *         functionalities of the Direct Memory Access (DMA) peripheral:
+  *           + Initialization and de-initialization functions
+  *           + IO operation functions
+  *           + Peripheral State and errors functions
+  @verbatim
+  ==============================================================================
+                        ##### How to use this driver #####
+  ==============================================================================
+  [..]
+   (#) Enable and configure the peripheral to be connected to the DMA Channel
+       (except for internal SRAM / FLASH memories: no initialization is
+       necessary).
+
+   (#) For a given Channel, program the required configuration through the following parameters:
+       Channel request, Transfer Direction, Source and Destination data formats,
+       Circular or Normal mode, Channel Priority level, Source and Destination Increment mode
+       using HAL_DMA_Init() function.
+
+   (#) Use HAL_DMA_GetState() function to return the DMA state and HAL_DMA_GetError() in case of error
+       detection.
+
+   (#) Use HAL_DMA_Abort() function to abort the current transfer
+
+     -@-   In Memory-to-Memory transfer mode, Circular mode is not allowed.
+
+     *** Polling mode IO operation ***
+     =================================
+    [..]
+          (+) Use HAL_DMA_Start() to start DMA transfer after the configuration of Source
+              address and destination address and the Length of data to be transferred
+          (+) Use HAL_DMA_PollForTransfer() to poll for the end of current transfer, in this
+              case a fixed Timeout can be configured by User depending from his application.
+
+     *** Interrupt mode IO operation ***
+     ===================================
+    [..]
+          (+) Configure the DMA interrupt priority using HAL_NVIC_SetPriority()
+          (+) Enable the DMA IRQ handler using HAL_NVIC_EnableIRQ()
+          (+) Use HAL_DMA_Start_IT() to start DMA transfer after the configuration of
+              Source address and destination address and the Length of data to be transferred.
+              In this case the DMA interrupt is configured
+          (+) Use HAL_DMA_IRQHandler() called under DMA_IRQHandler() Interrupt subroutine
+          (+) At the end of data transfer HAL_DMA_IRQHandler() function is executed and user can
+              add his own function to register callbacks with HAL_DMA_RegisterCallback().
+
+     *** DMA HAL driver macros list ***
+     =============================================
+      [..]
+       Below the list of macros in DMA HAL driver.
+
+       (+) __HAL_DMA_ENABLE: Enable the specified DMA Channel.
+       (+) __HAL_DMA_DISABLE: Disable the specified DMA Channel.
+       (+) __HAL_DMA_GET_FLAG: Get the DMA Channel pending flags.
+       (+) __HAL_DMA_CLEAR_FLAG: Clear the DMA Channel pending flags.
+       (+) __HAL_DMA_ENABLE_IT: Enable the specified DMA Channel interrupts.
+       (+) __HAL_DMA_DISABLE_IT: Disable the specified DMA Channel interrupts.
+       (+) __HAL_DMA_GET_IT_SOURCE: Check whether the specified DMA Channel interrupt has occurred or not.
+
+     [..]
+      (@) You can refer to the DMA HAL driver header file for more useful macros
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup DMA DMA
+  * @brief DMA HAL module driver
+  * @{
+  */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/** @defgroup DMA_Private_Functions DMA Private Functions
+  * @{
+  */
+
+static void DMA_SetConfig(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
+/**
+  * @}
+  */
+
+/* Exported functions ---------------------------------------------------------*/
+
+/** @defgroup DMA_Exported_Functions DMA Exported Functions
+  * @{
+  */
+
+/** @defgroup DMA_Exported_Functions_Group1 Initialization and de-initialization functions
+ *  @brief   Initialization and de-initialization functions
+ *
+@verbatim
+ ===============================================================================
+             ##### Initialization and de-initialization functions  #####
+ ===============================================================================
+    [..]
+    This section provides functions allowing to initialize the DMA Channel source
+    and destination addresses, incrementation and data sizes, transfer direction,
+    circular/normal mode selection, memory-to-memory mode selection and Channel priority value.
+    [..]
+    The HAL_DMA_Init() function follows the DMA configuration procedures as described in
+    reference manual.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Initialize the DMA according to the specified
+  *         parameters in the DMA_InitTypeDef and initialize the associated handle.
+  * @param  hdma Pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_Init(DMA_HandleTypeDef *hdma)
+{
+  uint32_t tmp;
+
+  /* Check the DMA handle allocation */
+  if(hdma == NULL)
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check the parameters */
+  assert_param(IS_DMA_ALL_INSTANCE(hdma->Instance));
+  assert_param(IS_DMA_ALL_REQUEST(hdma->Init.Request));
+  assert_param(IS_DMA_DIRECTION(hdma->Init.Direction));
+  assert_param(IS_DMA_PERIPHERAL_INC_STATE(hdma->Init.PeriphInc));
+  assert_param(IS_DMA_MEMORY_INC_STATE(hdma->Init.MemInc));
+  assert_param(IS_DMA_PERIPHERAL_DATA_SIZE(hdma->Init.PeriphDataAlignment));
+  assert_param(IS_DMA_MEMORY_DATA_SIZE(hdma->Init.MemDataAlignment));
+  assert_param(IS_DMA_MODE(hdma->Init.Mode));
+  assert_param(IS_DMA_PRIORITY(hdma->Init.Priority));
+
+  /* Compute the channel index */
+  /* Only one DMA: DMA1 */
+  hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA1_Channel1) / ((uint32_t)DMA1_Channel2 - (uint32_t)DMA1_Channel1)) << 2;
+  hdma->DmaBaseAddress = DMA1;
+
+  /* Change DMA peripheral state */
+  hdma->State = HAL_DMA_STATE_BUSY;
+
+  /* Get the CR register value */
+  tmp = hdma->Instance->CCR;
+
+  /* Clear PL, MSIZE, PSIZE, MINC, PINC, CIRC, DIR and MEM2MEM bits */
+  tmp &= ((uint32_t)~(DMA_CCR_PL    | DMA_CCR_MSIZE  | DMA_CCR_PSIZE  |
+                      DMA_CCR_MINC  | DMA_CCR_PINC   | DMA_CCR_CIRC   |
+                      DMA_CCR_DIR   | DMA_CCR_MEM2MEM));
+
+  /* Prepare the DMA Channel configuration */
+  tmp |=  hdma->Init.Direction        |
+          hdma->Init.PeriphInc           | hdma->Init.MemInc           |
+          hdma->Init.PeriphDataAlignment | hdma->Init.MemDataAlignment |
+          hdma->Init.Mode                | hdma->Init.Priority;
+
+  /* Write to DMA Channel CR register */
+  hdma->Instance->CCR = tmp;
+
+  /* Set request selection */
+  if(hdma->Init.Direction != DMA_MEMORY_TO_MEMORY)
+  {
+    /* Write to DMA channel selection register */
+    /* Reset request selection for DMA1 Channelx */
+    DMA1_CSELR->CSELR &= ~(DMA_CSELR_C1S << (hdma->ChannelIndex & 0x1cU));
+
+    /* Configure request selection for DMA1 Channelx */
+    DMA1_CSELR->CSELR |= (uint32_t) (hdma->Init.Request << (hdma->ChannelIndex & 0x1cU));
+  }
+
+  /* Initialise the error code */
+  hdma->ErrorCode = HAL_DMA_ERROR_NONE;
+
+  /* Initialize the DMA state*/
+  hdma->State  = HAL_DMA_STATE_READY;
+
+  /* Allocate lock resource and initialize it */
+  hdma->Lock = HAL_UNLOCKED;
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  DeInitialize the DMA peripheral.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_DeInit(DMA_HandleTypeDef *hdma)
+{
+
+  /* Check the DMA handle allocation */
+  if (NULL == hdma )
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check the parameters */
+  assert_param(IS_DMA_ALL_INSTANCE(hdma->Instance));
+
+  /* Disable the selected DMA Channelx */
+  __HAL_DMA_DISABLE(hdma);
+
+  /* Compute the channel index */
+  /* DMA1 */
+  hdma->ChannelIndex = (((uint32_t)hdma->Instance - (uint32_t)DMA1_Channel1) / ((uint32_t)DMA1_Channel2 - (uint32_t)DMA1_Channel1)) << 2;
+  hdma->DmaBaseAddress = DMA1;
+
+  /* Reset DMA Channel control register */
+  hdma->Instance->CCR  = 0U;
+
+  /* Clear all flags */
+  hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << (hdma->ChannelIndex & 0x1cU));
+
+  /* Reset DMA channel selection register */
+  /* DMA1 */
+  DMA1_CSELR->CSELR &= ~(DMA_CSELR_C1S << (hdma->ChannelIndex & 0x1cU));
+
+  /* Clean callbacks */
+  hdma->XferCpltCallback = NULL;
+  hdma->XferHalfCpltCallback = NULL;
+  hdma->XferErrorCallback = NULL;
+  hdma->XferAbortCallback = NULL;
+
+  /* Initialise the error code */
+  hdma->ErrorCode = HAL_DMA_ERROR_NONE;
+
+  /* Initialize the DMA state */
+  hdma->State = HAL_DMA_STATE_RESET;
+
+  /* Release Lock */
+  __HAL_UNLOCK(hdma);
+
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Exported_Functions_Group2 Input and Output operation functions
+ *  @brief   Input and Output operation functions
+ *
+@verbatim
+ ===============================================================================
+                      #####  IO operation functions  #####
+ ===============================================================================
+    [..]  This section provides functions allowing to:
+      (+) Configure the source, destination address and data length and Start DMA transfer
+      (+) Configure the source, destination address and data length and
+          Start DMA transfer with interrupt
+      (+) Abort DMA transfer
+      (+) Poll for transfer complete
+      (+) Handle DMA interrupt request
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Start the DMA Transfer.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.
+  * @param  SrcAddress The source memory Buffer address
+  * @param  DstAddress The destination memory Buffer address
+  * @param  DataLength The length of data to be transferred from source to destination
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_Start(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  /* Check the parameters */
+  assert_param(IS_DMA_BUFFER_SIZE(DataLength));
+
+  /* Process locked */
+  __HAL_LOCK(hdma);
+
+  if(HAL_DMA_STATE_READY == hdma->State)
+  {
+    /* Change DMA peripheral state */
+    hdma->State = HAL_DMA_STATE_BUSY;
+    hdma->ErrorCode = HAL_DMA_ERROR_NONE;
+
+    /* Disable the peripheral */
+    __HAL_DMA_DISABLE(hdma);
+
+    /* Configure the source, destination address and the data length & clear flags*/
+    DMA_SetConfig(hdma, SrcAddress, DstAddress, DataLength);
+
+    /* Enable the Peripheral */
+    __HAL_DMA_ENABLE(hdma);
+  }
+  else
+  {
+    /* Process Unlocked */
+    __HAL_UNLOCK(hdma);
+    status = HAL_BUSY;
+  }
+  return status;
+}
+
+/**
+  * @brief  Start the DMA Transfer with interrupt enabled.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.
+  * @param  SrcAddress The source memory Buffer address
+  * @param  DstAddress The destination memory Buffer address
+  * @param  DataLength The length of data to be transferred from source to destination
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  /* Check the parameters */
+  assert_param(IS_DMA_BUFFER_SIZE(DataLength));
+
+  /* Process locked */
+  __HAL_LOCK(hdma);
+
+  if(HAL_DMA_STATE_READY == hdma->State)
+  {
+    /* Change DMA peripheral state */
+    hdma->State = HAL_DMA_STATE_BUSY;
+    hdma->ErrorCode = HAL_DMA_ERROR_NONE;
+
+    /* Disable the peripheral */
+    __HAL_DMA_DISABLE(hdma);
+
+    /* Configure the source, destination address and the data length & clear flags*/
+    DMA_SetConfig(hdma, SrcAddress, DstAddress, DataLength);
+
+    /* Enable the transfer complete interrupt */
+    /* Enable the transfer Error interrupt */
+    if(NULL != hdma->XferHalfCpltCallback )
+    {
+      /* Enable the Half transfer complete interrupt as well */
+      __HAL_DMA_ENABLE_IT(hdma, (DMA_IT_TC | DMA_IT_HT | DMA_IT_TE));
+    }
+    else
+    {
+      __HAL_DMA_DISABLE_IT(hdma, DMA_IT_HT);
+      __HAL_DMA_ENABLE_IT(hdma, (DMA_IT_TC | DMA_IT_TE));
+    }
+
+    /* Enable the Peripheral */
+    __HAL_DMA_ENABLE(hdma);
+  }
+  else
+  {
+    /* Process Unlocked */
+    __HAL_UNLOCK(hdma);
+
+    /* Remain BUSY */
+    status = HAL_BUSY;
+  }
+  return status;
+}
+
+/**
+  * @brief  Abort the DMA Transfer.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.
+    * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef *hdma)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  /* Check the DMA peripheral state */
+  if(hdma->State != HAL_DMA_STATE_BUSY)
+  {
+    hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hdma);
+
+    return HAL_ERROR;
+  }
+  else
+  {
+    /* Disable DMA IT */
+    __HAL_DMA_DISABLE_IT(hdma, (DMA_IT_TC | DMA_IT_HT | DMA_IT_TE));
+
+    /* Disable the channel */
+    __HAL_DMA_DISABLE(hdma);
+
+    /* Clear all flags */
+    hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << (hdma->ChannelIndex & 0x1cU));
+
+    /* Change the DMA state */
+    hdma->State = HAL_DMA_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hdma);
+
+    return status;
+  }
+}
+
+/**
+  * @brief  Aborts the DMA Transfer in Interrupt mode.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *                 the configuration information for the specified DMA Channel.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_Abort_IT(DMA_HandleTypeDef *hdma)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  if(HAL_DMA_STATE_BUSY != hdma->State)
+  {
+    /* no transfer ongoing */
+    hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER;
+
+    status = HAL_ERROR;
+  }
+  else
+  {
+    /* Disable DMA IT */
+    __HAL_DMA_DISABLE_IT(hdma, (DMA_IT_TC | DMA_IT_HT | DMA_IT_TE));
+
+    /* Disable the channel */
+    __HAL_DMA_DISABLE(hdma);
+
+    /* Clear all flags */
+    hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << (hdma->ChannelIndex & 0x1cU));
+
+    /* Change the DMA state */
+    hdma->State = HAL_DMA_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hdma);
+
+    /* Call User Abort callback */
+    if(hdma->XferAbortCallback != NULL)
+    {
+      hdma->XferAbortCallback(hdma);
+    }
+  }
+  return status;
+}
+
+/**
+  * @brief  Polling for transfer complete.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *                  the configuration information for the specified DMA Channel.
+  * @param  CompleteLevel Specifies the DMA level complete.
+  * @param  Timeout       Timeout duration.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, HAL_DMA_LevelCompleteTypeDef CompleteLevel, uint32_t Timeout)
+{
+  uint32_t temp;
+  uint32_t tickstart;
+
+  if(HAL_DMA_STATE_BUSY != hdma->State)
+  {
+    /* no transfer ongoing */
+    hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER;
+    __HAL_UNLOCK(hdma);
+    return HAL_ERROR;
+  }
+
+  /* Polling mode not supported in circular mode */
+  if (0U != (hdma->Instance->CCR & DMA_CCR_CIRC))
+  {
+    hdma->ErrorCode = HAL_DMA_ERROR_NOT_SUPPORTED;
+    return HAL_ERROR;
+  }
+
+  /* Get the level transfer complete flag */
+  if (HAL_DMA_FULL_TRANSFER == CompleteLevel)
+  {
+    /* Transfer Complete flag */
+    temp = DMA_FLAG_TC1 << (hdma->ChannelIndex & 0x1cU);
+  }
+  else
+  {
+    /* Half Transfer Complete flag */
+    temp = DMA_FLAG_HT1 << (hdma->ChannelIndex & 0x1cU);
+  }
+
+  /* Get tick */
+  tickstart = HAL_GetTick();
+
+  while(0U == (hdma->DmaBaseAddress->ISR & temp))
+  {
+    if((0U != (hdma->DmaBaseAddress->ISR & (DMA_FLAG_TE1 << (hdma->ChannelIndex& 0x1cU)))))
+    {
+      /* When a DMA transfer error occurs */
+      /* A hardware clear of its EN bits is performed */
+      /* Clear all flags */
+      hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << (hdma->ChannelIndex & 0x1cU));
+
+      /* Update error code */
+      hdma->ErrorCode = HAL_DMA_ERROR_TE;
+
+      /* Change the DMA state */
+      hdma->State= HAL_DMA_STATE_READY;
+
+      /* Process Unlocked */
+      __HAL_UNLOCK(hdma);
+
+      return HAL_ERROR;
+    }
+    /* Check for the Timeout */
+    if(Timeout != HAL_MAX_DELAY)
+    {
+      if(((HAL_GetTick() - tickstart) > Timeout) ||  (Timeout == 0U))
+      {
+        /* Update error code */
+        hdma->ErrorCode = HAL_DMA_ERROR_TIMEOUT;
+
+        /* Change the DMA state */
+        hdma->State = HAL_DMA_STATE_READY;
+
+        /* Process Unlocked */
+        __HAL_UNLOCK(hdma);
+
+        return HAL_ERROR;
+      }
+    }
+  }
+
+  if(HAL_DMA_FULL_TRANSFER == CompleteLevel)
+  {
+    /* Clear the transfer complete flag */
+    hdma->DmaBaseAddress->IFCR = (DMA_FLAG_TC1 << (hdma->ChannelIndex& 0x1cU));
+
+    /* The selected Channelx EN bit is cleared (DMA is disabled and
+    all transfers are complete) */
+    hdma->State = HAL_DMA_STATE_READY;
+  }
+  else
+  {
+    /* Clear the half transfer complete flag */
+    hdma->DmaBaseAddress->IFCR = (DMA_FLAG_HT1 << (hdma->ChannelIndex & 0x1cU));
+  }
+
+  /* Process unlocked */
+  __HAL_UNLOCK(hdma);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Handle DMA interrupt request.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.
+  * @retval None
+  */
+void HAL_DMA_IRQHandler(DMA_HandleTypeDef *hdma)
+{
+  uint32_t flag_it = hdma->DmaBaseAddress->ISR;
+  uint32_t source_it = hdma->Instance->CCR;
+
+  /* Half Transfer Complete Interrupt management ******************************/
+  if ((0U != (flag_it & (DMA_FLAG_HT1 << (hdma->ChannelIndex & 0x1cU)))) && (0U != (source_it & DMA_IT_HT)))
+  {
+      /* Disable the half transfer interrupt if the DMA mode is not CIRCULAR */
+      if((hdma->Instance->CCR & DMA_CCR_CIRC) == 0U)
+      {
+        /* Disable the half transfer interrupt */
+        __HAL_DMA_DISABLE_IT(hdma, DMA_IT_HT);
+      }
+      /* Clear the half transfer complete flag */
+      hdma->DmaBaseAddress->IFCR = DMA_ISR_HTIF1 << (hdma->ChannelIndex & 0x1cU);
+
+      /* DMA peripheral state is not updated in Half Transfer */
+      /* but in Transfer Complete case */
+
+     if(hdma->XferHalfCpltCallback != NULL)
+      {
+        /* Half transfer callback */
+        hdma->XferHalfCpltCallback(hdma);
+      }
+  }
+
+  /* Transfer Complete Interrupt management ***********************************/
+  else if ((0U != (flag_it & (DMA_FLAG_TC1 << (hdma->ChannelIndex & 0x1cU)))) && (0U != (source_it & DMA_IT_TC)))
+  {
+    if((hdma->Instance->CCR & DMA_CCR_CIRC) == 0U)
+    {
+      /* Disable the transfer complete and error interrupt */
+      __HAL_DMA_DISABLE_IT(hdma, DMA_IT_TE | DMA_IT_TC);
+
+      /* Change the DMA state */
+      hdma->State = HAL_DMA_STATE_READY;
+    }
+    /* Clear the transfer complete flag */
+    hdma->DmaBaseAddress->IFCR = (DMA_ISR_TCIF1 << (hdma->ChannelIndex & 0x1cU));
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hdma);
+
+    if(hdma->XferCpltCallback != NULL)
+    {
+      /* Transfer complete callback */
+      hdma->XferCpltCallback(hdma);
+    }
+  }
+
+  /* Transfer Error Interrupt management **************************************/
+  else if ((0U != (flag_it & (DMA_FLAG_TE1 << (hdma->ChannelIndex & 0x1cU)))) && (0U != (source_it & DMA_IT_TE)))
+  {
+    /* When a DMA transfer error occurs */
+    /* A hardware clear of its EN bits is performed */
+    /* Disable ALL DMA IT */
+    __HAL_DMA_DISABLE_IT(hdma, (DMA_IT_TC | DMA_IT_HT | DMA_IT_TE));
+
+    /* Clear all flags */
+    hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << (hdma->ChannelIndex & 0x1cU));
+
+    /* Update error code */
+    hdma->ErrorCode = HAL_DMA_ERROR_TE;
+
+    /* Change the DMA state */
+    hdma->State = HAL_DMA_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hdma);
+
+    if (hdma->XferErrorCallback != NULL)
+    {
+      /* Transfer error callback */
+      hdma->XferErrorCallback(hdma);
+    }
+  }
+  else
+  {
+    /* Nothing To Do */
+  }
+  return;
+}
+
+/**
+  * @brief  Register callbacks
+  * @param  hdma                 pointer to a DMA_HandleTypeDef structure that contains
+  *                               the configuration information for the specified DMA Channel.
+  * @param  CallbackID           User Callback identifer
+  *                               a HAL_DMA_CallbackIDTypeDef ENUM as parameter.
+  * @param  pCallback            pointer to private callbacsk function which has pointer to
+  *                               a DMA_HandleTypeDef structure as parameter.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_RegisterCallback(DMA_HandleTypeDef *hdma, HAL_DMA_CallbackIDTypeDef CallbackID, void (* pCallback)( DMA_HandleTypeDef * _hdma))
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  /* Process locked */
+  __HAL_LOCK(hdma);
+
+  if(HAL_DMA_STATE_READY == hdma->State)
+  {
+    switch (CallbackID)
+    {
+     case  HAL_DMA_XFER_CPLT_CB_ID:
+           hdma->XferCpltCallback = pCallback;
+           break;
+
+     case  HAL_DMA_XFER_HALFCPLT_CB_ID:
+           hdma->XferHalfCpltCallback = pCallback;
+           break;
+
+     case  HAL_DMA_XFER_ERROR_CB_ID:
+           hdma->XferErrorCallback = pCallback;
+           break;
+
+     case  HAL_DMA_XFER_ABORT_CB_ID:
+           hdma->XferAbortCallback = pCallback;
+           break;
+
+     default:
+           status = HAL_ERROR;
+           break;
+    }
+  }
+  else
+  {
+    status = HAL_ERROR;
+  }
+
+  /* Release Lock */
+  __HAL_UNLOCK(hdma);
+
+  return status;
+}
+
+/**
+  * @brief  UnRegister callbacks
+  * @param  hdma                 pointer to a DMA_HandleTypeDef structure that contains
+  *                               the configuration information for the specified DMA Channel.
+  * @param  CallbackID           User Callback identifer
+  *                               a HAL_DMA_CallbackIDTypeDef ENUM as parameter.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_DMA_UnRegisterCallback(DMA_HandleTypeDef *hdma, HAL_DMA_CallbackIDTypeDef CallbackID)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+    /* Process locked */
+  __HAL_LOCK(hdma);
+
+  if(HAL_DMA_STATE_READY == hdma->State)
+  {
+    switch (CallbackID)
+    {
+     case  HAL_DMA_XFER_CPLT_CB_ID:
+           hdma->XferCpltCallback = NULL;
+           break;
+
+     case  HAL_DMA_XFER_HALFCPLT_CB_ID:
+           hdma->XferHalfCpltCallback = NULL;
+           break;
+
+     case  HAL_DMA_XFER_ERROR_CB_ID:
+           hdma->XferErrorCallback = NULL;
+           break;
+
+     case  HAL_DMA_XFER_ABORT_CB_ID:
+           hdma->XferAbortCallback = NULL;
+           break;
+
+    case   HAL_DMA_XFER_ALL_CB_ID:
+           hdma->XferCpltCallback = NULL;
+           hdma->XferHalfCpltCallback = NULL;
+           hdma->XferErrorCallback = NULL;
+           hdma->XferAbortCallback = NULL;
+           break;
+
+    default:
+           status = HAL_ERROR;
+           break;
+    }
+  }
+  else
+  {
+    status = HAL_ERROR;
+  }
+
+  /* Release Lock */
+  __HAL_UNLOCK(hdma);
+
+  return status;
+}
+
+/**
+  * @}
+  */
+
+
+
+/** @defgroup DMA_Exported_Functions_Group3 Peripheral State and Errors functions
+ *  @brief    Peripheral State and Errors functions
+ *
+@verbatim
+ ===============================================================================
+            ##### Peripheral State and Errors functions #####
+ ===============================================================================
+    [..]
+    This subsection provides functions allowing to
+      (+) Check the DMA state
+      (+) Get error code
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Return the DMA handle state.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *               the configuration information for the specified DMA Channel.
+  * @retval HAL state
+  */
+HAL_DMA_StateTypeDef HAL_DMA_GetState(DMA_HandleTypeDef *hdma)
+{
+  /* Return DMA handle state */
+  return hdma->State;
+}
+
+/**
+  * @brief  Return the DMA error code.
+  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
+  *              the configuration information for the specified DMA Channel.
+  * @retval DMA Error Code
+  */
+uint32_t HAL_DMA_GetError(DMA_HandleTypeDef *hdma)
+{
+  return hdma->ErrorCode;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup DMA_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Sets the DMA Transfer parameter.
+  * @param  hdma       pointer to a DMA_HandleTypeDef structure that contains
+  *                     the configuration information for the specified DMA Channel.
+  * @param  SrcAddress The source memory Buffer address
+  * @param  DstAddress The destination memory Buffer address
+  * @param  DataLength The length of data to be transferred from source to destination
+  * @retval HAL status
+  */
+static void DMA_SetConfig(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength)
+{
+  /* Clear all flags */
+  hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << (hdma->ChannelIndex & 0x1cU));
+
+  /* Configure DMA Channel data length */
+  hdma->Instance->CNDTR = DataLength;
+
+  /* Memory to Peripheral */
+  if((hdma->Init.Direction) == DMA_MEMORY_TO_PERIPH)
+  {
+    /* Configure DMA Channel destination address */
+    hdma->Instance->CPAR = DstAddress;
+
+    /* Configure DMA Channel source address */
+    hdma->Instance->CMAR = SrcAddress;
+  }
+  /* Peripheral to Memory */
+  else
+  {
+    /* Configure DMA Channel source address */
+    hdma->Instance->CPAR = SrcAddress;
+
+    /* Configure DMA Channel destination address */
+    hdma->Instance->CMAR = DstAddress;
+  }
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_DMA_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_exti.c

@@ -0,0 +1,549 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_exti.c
+  * @author  MCD Application Team
+  * @brief   EXTI HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the Extended Interrupts and events controller (EXTI) peripheral:
+  *           + Initialization and de-initialization functions
+  *           + IO operation functions
+  *
+  @verbatim
+  ==============================================================================
+                    ##### EXTI Peripheral features #####
+  ==============================================================================
+  [..]
+    (+) Each Exti line can be configured within this driver.
+
+    (+) Exti line can be configured in 3 different modes
+        (++) Interrupt
+        (++) Event
+        (++) Both of them
+
+    (+) Configurable Exti lines can be configured with 3 different triggers
+        (++) Rising
+        (++) Falling
+        (++) Both of them
+
+    (+) When set in interrupt mode, configurable Exti lines have two different
+        interrupts pending registers which allow to distinguish which transition
+        occurs:
+        (++) Rising edge pending interrupt
+        (++) Falling
+
+    (+) Exti lines 0 to 15 are linked to gpio pin number 0 to 15. Gpio port can
+        be selected through multiplexer.
+
+                     ##### How to use this driver #####
+  ==============================================================================
+  [..]
+
+    (#) Configure the EXTI line using HAL_EXTI_SetConfigLine().
+        (++) Choose the interrupt line number by setting "Line" member from
+             EXTI_ConfigTypeDef structure.
+        (++) Configure the interrupt and/or event mode using "Mode" member from
+             EXTI_ConfigTypeDef structure.
+        (++) For configurable lines, configure rising and/or falling trigger
+             "Trigger" member from EXTI_ConfigTypeDef structure.
+        (++) For Exti lines linked to gpio, choose gpio port using "GPIOSel"
+             member from GPIO_InitTypeDef structure.
+
+    (#) Get current Exti configuration of a dedicated line using
+        HAL_EXTI_GetConfigLine().
+        (++) Provide exiting handle as parameter.
+        (++) Provide pointer on EXTI_ConfigTypeDef structure as second parameter.
+
+    (#) Clear Exti configuration of a dedicated line using HAL_EXTI_GetConfigLine().
+        (++) Provide exiting handle as parameter.
+
+    (#) Register callback to treat Exti interrupts using HAL_EXTI_RegisterCallback().
+        (++) Provide exiting handle as first parameter.
+        (++) Provide which callback will be registered using one value from
+             EXTI_CallbackIDTypeDef.
+        (++) Provide callback function pointer.
+
+    (#) Get interrupt pending bit using HAL_EXTI_GetPending().
+
+    (#) Clear interrupt pending bit using HAL_EXTI_GetPending().
+
+    (#) Generate software interrupt using HAL_EXTI_GenerateSWI().
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup EXTI
+  * @{
+  */
+/** MISRA C:2012 deviation rule has been granted for following rule:
+  * Rule-18.1_b - Medium: Array `EXTICR' 1st subscript interval [0,7] may be out
+  * of bounds [0,3] in following API :
+  * HAL_EXTI_SetConfigLine
+  * HAL_EXTI_GetConfigLine
+  * HAL_EXTI_ClearConfigLine
+  */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private defines -----------------------------------------------------------*/
+/** @defgroup EXTI_Private_Constants EXTI Private Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup EXTI_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup EXTI_Exported_Functions_Group1
+  *  @brief    Configuration functions
+  *
+@verbatim
+ ===============================================================================
+              ##### Configuration functions #####
+ ===============================================================================
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Set configuration of a dedicated Exti line.
+  * @param  hexti Exti handle.
+  * @param  pExtiConfig Pointer on EXTI configuration to be set.
+  * @retval HAL Status.
+  */
+HAL_StatusTypeDef HAL_EXTI_SetConfigLine(EXTI_HandleTypeDef *hexti, EXTI_ConfigTypeDef *pExtiConfig)
+{
+  uint32_t regval;
+  uint32_t linepos;
+  uint32_t maskline;
+
+  /* Check null pointer */
+  if ((hexti == NULL) || (pExtiConfig == NULL))
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check parameters */
+  assert_param(IS_EXTI_LINE(pExtiConfig->Line));
+  assert_param(IS_EXTI_MODE(pExtiConfig->Mode));
+
+  /* Assign line number to handle */
+  hexti->Line = pExtiConfig->Line;
+
+  /* Compute line mask */
+  linepos = (pExtiConfig->Line & EXTI_PIN_MASK);
+  maskline = (1uL << linepos);
+
+  /* Configure triggers for configurable lines */
+  if ((pExtiConfig->Line & EXTI_CONFIG) != 0x00u)
+  {
+    assert_param(IS_EXTI_TRIGGER(pExtiConfig->Trigger));
+
+    /* Configure rising trigger */
+    /* Mask or set line */
+    if ((pExtiConfig->Trigger & EXTI_TRIGGER_RISING) != 0x00u)
+    {
+      EXTI->RTSR |= maskline;
+    }
+    else
+    {
+      EXTI->RTSR &= ~maskline;
+    }
+
+    /* Configure falling trigger */
+    /* Mask or set line */
+    if ((pExtiConfig->Trigger & EXTI_TRIGGER_FALLING) != 0x00u)
+    {
+      EXTI->FTSR |= maskline;
+    }
+    else
+    {
+      EXTI->FTSR &= ~maskline;
+    }
+
+
+    /* Configure gpio port selection in case of gpio exti line */
+    if ((pExtiConfig->Line & EXTI_GPIO) == EXTI_GPIO)
+    {
+      assert_param(IS_EXTI_GPIO_PORT(pExtiConfig->GPIOSel));
+      assert_param(IS_EXTI_GPIO_PIN(linepos));
+
+      regval = SYSCFG->EXTICR[linepos >> 2u];
+      regval &= ~(SYSCFG_EXTICR1_EXTI0 << (SYSCFG_EXTICR1_EXTI1_Pos * (linepos & 0x03u)));
+      regval |= (pExtiConfig->GPIOSel << (SYSCFG_EXTICR1_EXTI1_Pos * (linepos & 0x03u)));
+      SYSCFG->EXTICR[linepos >> 2u] = regval;
+    }
+  }
+
+  /* Configure interrupt mode : read current mode */
+  /* Mask or set line */
+  if ((pExtiConfig->Mode & EXTI_MODE_INTERRUPT) != 0x00u)
+  {
+    EXTI->IMR |= maskline;
+  }
+  else
+  {
+    EXTI->IMR &= ~maskline;
+  }
+
+  /* Configure event mode : read current mode */
+  /* Mask or set line */
+  if ((pExtiConfig->Mode & EXTI_MODE_EVENT) != 0x00u)
+  {
+    EXTI->EMR |= maskline;
+  }
+  else
+  {
+    EXTI->EMR &= ~maskline;
+  }
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Get configuration of a dedicated Exti line.
+  * @param  hexti Exti handle.
+  * @param  pExtiConfig Pointer on structure to store Exti configuration.
+  * @retval HAL Status.
+  */
+HAL_StatusTypeDef HAL_EXTI_GetConfigLine(EXTI_HandleTypeDef *hexti, EXTI_ConfigTypeDef *pExtiConfig)
+{
+  uint32_t regval;
+  uint32_t linepos;
+  uint32_t maskline;
+
+  /* Check null pointer */
+  if ((hexti == NULL) || (pExtiConfig == NULL))
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check the parameter */
+  assert_param(IS_EXTI_LINE(hexti->Line));
+
+  /* Store handle line number to configuration structure */
+  pExtiConfig->Line = hexti->Line;
+
+  /* Compute line mask */
+  linepos = (pExtiConfig->Line & EXTI_PIN_MASK);
+  maskline = (1uL << linepos);
+
+  /* 1] Get core mode : interrupt */
+
+  /* Check if selected line is enable */
+  if ((EXTI->IMR & maskline) != 0x00u)
+  {
+    pExtiConfig->Mode = EXTI_MODE_INTERRUPT;
+  }
+  else
+  {
+    pExtiConfig->Mode = EXTI_MODE_NONE;
+  }
+
+  /* Get event mode */
+  /* Check if selected line is enable */
+  if ((EXTI->EMR & maskline) != 0x00u)
+  {
+    pExtiConfig->Mode |= EXTI_MODE_EVENT;
+  }
+
+  /* Get default Trigger and GPIOSel configuration */
+  pExtiConfig->Trigger = EXTI_TRIGGER_NONE;
+  pExtiConfig->GPIOSel = 0x00u;
+
+  /* 2] Get trigger for configurable lines : rising */
+  if ((pExtiConfig->Line & EXTI_CONFIG) != 0x00u)
+  {
+    /* Check if configuration of selected line is enable */
+    if ((EXTI->RTSR & maskline) != 0x00u)
+    {
+      pExtiConfig->Trigger = EXTI_TRIGGER_RISING;
+    }
+
+    /* Get falling configuration */
+    /* Check if configuration of selected line is enable */
+    if ((EXTI->FTSR & maskline) != 0x00u)
+    {
+      pExtiConfig->Trigger |= EXTI_TRIGGER_FALLING;
+    }
+
+    /* Get Gpio port selection for gpio lines */
+    if ((pExtiConfig->Line & EXTI_GPIO) == EXTI_GPIO)
+    {
+      assert_param(IS_EXTI_GPIO_PIN(linepos));
+
+      regval = SYSCFG->EXTICR[linepos >> 2u];
+      pExtiConfig->GPIOSel = ((regval << (SYSCFG_EXTICR1_EXTI1_Pos * (3uL - (linepos & 0x03u)))) >> 24);
+    }
+  }
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Clear whole configuration of a dedicated Exti line.
+  * @param  hexti Exti handle.
+  * @retval HAL Status.
+  */
+HAL_StatusTypeDef HAL_EXTI_ClearConfigLine(EXTI_HandleTypeDef *hexti)
+{
+  uint32_t regval;
+  uint32_t linepos;
+  uint32_t maskline;
+
+  /* Check null pointer */
+  if (hexti == NULL)
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check the parameter */
+  assert_param(IS_EXTI_LINE(hexti->Line));
+
+  /* compute line mask */
+  linepos = (hexti->Line & EXTI_PIN_MASK);
+  maskline = (1uL << linepos);
+
+  /* 1] Clear interrupt mode */
+  EXTI->IMR = (EXTI->IMR & ~maskline);
+
+  /* 2] Clear event mode */
+  EXTI->EMR = (EXTI->EMR & ~maskline);
+
+  /* 3] Clear triggers in case of configurable lines */
+  if ((hexti->Line & EXTI_CONFIG) != 0x00u)
+  {
+    EXTI->RTSR = (EXTI->RTSR & ~maskline);
+    EXTI->FTSR = (EXTI->FTSR & ~maskline);
+
+    /* Get Gpio port selection for gpio lines */
+    if ((hexti->Line & EXTI_GPIO) == EXTI_GPIO)
+    {
+      assert_param(IS_EXTI_GPIO_PIN(linepos));
+
+      regval = SYSCFG->EXTICR[linepos >> 2u];
+      regval &= ~(SYSCFG_EXTICR1_EXTI0 << (SYSCFG_EXTICR1_EXTI1_Pos * (linepos & 0x03u)));
+      SYSCFG->EXTICR[linepos >> 2u] = regval;
+    }
+  }
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Register callback for a dedicated Exti line.
+  * @param  hexti Exti handle.
+  * @param  CallbackID User callback identifier.
+  *         This parameter can be one of @arg @ref EXTI_CallbackIDTypeDef values.
+  * @param  pPendingCbfn function pointer to be stored as callback.
+  * @retval HAL Status.
+  */
+HAL_StatusTypeDef HAL_EXTI_RegisterCallback(EXTI_HandleTypeDef *hexti, EXTI_CallbackIDTypeDef CallbackID, void (*pPendingCbfn)(void))
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  switch (CallbackID)
+  {
+    case  HAL_EXTI_COMMON_CB_ID:
+      hexti->PendingCallback = pPendingCbfn;
+      break;
+
+    default:
+      status = HAL_ERROR;
+      break;
+  }
+
+  return status;
+}
+
+/**
+  * @brief  Store line number as handle private field.
+  * @param  hexti Exti handle.
+  * @param  ExtiLine Exti line number.
+  *         This parameter can be from 0 to @ref EXTI_LINE_NB.
+  * @retval HAL Status.
+  */
+HAL_StatusTypeDef HAL_EXTI_GetHandle(EXTI_HandleTypeDef *hexti, uint32_t ExtiLine)
+{
+  /* Check the parameters */
+  assert_param(IS_EXTI_LINE(ExtiLine));
+
+  /* Check null pointer */
+  if (hexti == NULL)
+  {
+    return HAL_ERROR;
+  }
+  else
+  {
+    /* Store line number as handle private field */
+    hexti->Line = ExtiLine;
+
+    return HAL_OK;
+  }
+}
+
+/**
+  * @}
+  */
+
+/** @addtogroup EXTI_Exported_Functions_Group2
+  *  @brief EXTI IO functions.
+  *
+@verbatim
+ ===============================================================================
+                       ##### IO operation functions #####
+ ===============================================================================
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Handle EXTI interrupt request.
+  * @param  hexti Exti handle.
+  * @retval none.
+  */
+void HAL_EXTI_IRQHandler(EXTI_HandleTypeDef *hexti)
+{
+  uint32_t regval;
+  uint32_t maskline;
+
+  /* Compute line mask */
+  maskline = (1uL << (hexti->Line & EXTI_PIN_MASK));
+
+  /* Get pending bit  */
+  regval = (EXTI->PR & maskline);
+  if (regval != 0x00u)
+  {
+    /* Clear pending bit */
+    EXTI->PR = maskline;
+
+    /* Call callback */
+    if (hexti->PendingCallback != NULL)
+    {
+      hexti->PendingCallback();
+    }
+  }
+}
+
+/**
+  * @brief  Get interrupt pending bit of a dedicated line.
+  * @param  hexti Exti handle.
+  * @param  Edge Specify which pending edge as to be checked.
+  *         This parameter can be one of the following values:
+  *           @arg @ref EXTI_TRIGGER_RISING_FALLING
+  *         This parameter is kept for compatibility with other series.
+  * @retval 1 if interrupt is pending else 0.
+  */
+uint32_t HAL_EXTI_GetPending(EXTI_HandleTypeDef *hexti, uint32_t Edge)
+{
+  uint32_t regval;
+  uint32_t linepos;
+  uint32_t maskline;
+
+  /* Check parameters */
+  assert_param(IS_EXTI_LINE(hexti->Line));
+  assert_param(IS_EXTI_CONFIG_LINE(hexti->Line));
+  assert_param(IS_EXTI_PENDING_EDGE(Edge));
+
+  /* Compute line mask */
+  linepos = (hexti->Line & EXTI_PIN_MASK);
+  maskline = (1uL << linepos);
+
+  /* return 1 if bit is set else 0 */
+  regval = ((EXTI->PR & maskline) >> linepos);
+  return regval;
+}
+
+/**
+  * @brief  Clear interrupt pending bit of a dedicated line.
+  * @param  hexti Exti handle.
+  * @param  Edge Specify which pending edge as to be clear.
+  *         This parameter can be one of the following values:
+  *           @arg @ref EXTI_TRIGGER_RISING_FALLING
+  *         This parameter is kept for compatibility with other series.
+  * @retval None.
+  */
+void HAL_EXTI_ClearPending(EXTI_HandleTypeDef *hexti, uint32_t Edge)
+{
+  uint32_t maskline;
+
+  /* Check parameters */
+  assert_param(IS_EXTI_LINE(hexti->Line));
+  assert_param(IS_EXTI_CONFIG_LINE(hexti->Line));
+  assert_param(IS_EXTI_PENDING_EDGE(Edge));
+
+  /* Compute line mask */
+  maskline = (1uL << (hexti->Line & EXTI_PIN_MASK));
+
+  /* Clear Pending bit */
+  EXTI->PR =  maskline;
+}
+
+/**
+  * @brief  Generate a software interrupt for a dedicated line.
+  * @param  hexti Exti handle.
+  * @retval None.
+  */
+void HAL_EXTI_GenerateSWI(EXTI_HandleTypeDef *hexti)
+{
+  uint32_t maskline;
+
+  /* Check parameters */
+  assert_param(IS_EXTI_LINE(hexti->Line));
+  assert_param(IS_EXTI_CONFIG_LINE(hexti->Line));
+
+  /* Compute line mask */
+  maskline = (1uL << (hexti->Line & EXTI_PIN_MASK));
+
+  /* Generate Software interrupt */
+  EXTI->SWIER = maskline;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_EXTI_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_flash.c

@@ -0,0 +1,769 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_flash.c
+  * @author  MCD Application Team
+  * @brief   FLASH HAL module driver.
+  *          This file provides firmware functions to manage the following 
+  *          functionalities of the internal FLASH memory:
+  *           + Program operations functions
+  *           + Memory Control functions 
+  *           + Peripheral State functions
+  *         
+  @verbatim
+  ==============================================================================
+                        ##### FLASH peripheral features #####
+  ==============================================================================
+  [..] The Flash memory interface manages CPU AHB I-Code and D-Code accesses 
+       to the Flash memory. It implements the erase and program Flash memory operations 
+       and the read and write protection mechanisms.
+
+  [..] The Flash memory interface accelerates code execution with a system of instruction
+      prefetch. 
+
+  [..] The FLASH main features are:
+      (+) Flash memory read operations
+      (+) Flash memory program/erase operations
+      (+) Read / write protections
+      (+) Prefetch on I-Code
+      (+) Option Bytes programming
+
+
+                     ##### How to use this driver #####
+  ==============================================================================
+  [..]                             
+      This driver provides functions and macros to configure and program the FLASH 
+      memory of all STM32L0xx devices.
+    
+      (#) FLASH Memory I/O Programming functions: this group includes all needed
+          functions to erase and program the main memory:
+        (++) Lock and Unlock the FLASH interface
+        (++) Erase function: Erase page
+        (++) Program functions: Fast Word and Half Page(should be 
+        executed from internal SRAM).
+  
+      (#) DATA EEPROM Programming functions: this group includes all 
+          needed functions to erase and program the DATA EEPROM memory:
+        (++) Lock and Unlock the DATA EEPROM interface.
+        (++) Erase function: Erase Byte, erase HalfWord, erase Word, erase 
+             Double Word (should be executed from internal SRAM).
+        (++) Program functions: Fast Program Byte, Fast Program Half-Word, 
+             FastProgramWord, Program Byte, Program Half-Word, 
+             Program Word and Program Double-Word (should be executed 
+             from internal SRAM).
+
+      (#) FLASH Option Bytes Programming functions: this group includes all needed
+          functions to manage the Option Bytes:
+        (++) Lock and Unlock the Option Bytes
+        (++) Set/Reset the write protection
+        (++) Set the Read protection Level
+        (++) Program the user Option Bytes
+        (++) Launch the Option Bytes loader
+        (++) Set/Get the Read protection Level.
+        (++) Set/Get the BOR level.
+        (++) Get the Write protection.
+        (++) Get the user option bytes.
+    
+      (#) Interrupts and flags management functions : this group 
+          includes all needed functions to:
+        (++) Handle FLASH interrupts
+        (++) Wait for last FLASH operation according to its status
+        (++) Get error flag status
+
+    (#) FLASH Interface configuration functions: this group includes 
+      the management of following features:
+      (++) Enable/Disable the RUN PowerDown mode.
+      (++) Enable/Disable the SLEEP PowerDown mode.  
+  
+    (#) FLASH Peripheral State methods: this group includes 
+      the management of following features:
+      (++) Wait for the FLASH operation
+      (++)  Get the specific FLASH error flag
+    
+  [..] In addition to these function, this driver includes a set of macros allowing
+       to handle the following operations:
+      
+      (+) Set/Get the latency
+      (+) Enable/Disable the prefetch buffer
+      (+) Enable/Disable the preread buffer
+      (+) Enable/Disable the Flash power-down
+      (+) Enable/Disable the FLASH interrupts
+      (+) Monitor the FLASH flags status
+          
+                 ##### Programming operation functions #####
+  ===============================================================================  
+     [..]
+     This subsection provides a set of functions allowing to manage the FLASH 
+     program operations.
+  
+    [..] The FLASH Memory Programming functions, includes the following functions:
+     (+) HAL_FLASH_Unlock(void);
+     (+) HAL_FLASH_Lock(void);
+     (+) HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint32_t Data)
+     (+) HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint32_t Data)
+    
+     [..] Any operation of erase or program should follow these steps:
+     (#) Call the HAL_FLASH_Unlock() function to enable the flash control register and 
+         program memory access.
+     (#) Call the desired function to erase page or program data.
+     (#) Call the HAL_FLASH_Lock() to disable the flash program memory access 
+        (recommended to protect the FLASH memory against possible unwanted operation).
+  
+               ##### Option Bytes Programming functions ##### 
+   ==============================================================================  
+  
+     [..] The FLASH_Option Bytes Programming_functions, includes the following functions:
+     (+) HAL_FLASH_OB_Unlock(void);
+     (+) HAL_FLASH_OB_Lock(void);
+     (+) HAL_FLASH_OB_Launch(void);
+     (+) HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit);
+     (+) HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef *pOBInit);
+    
+     [..] Any operation of erase or program should follow these steps:
+     (#) Call the HAL_FLASH_OB_Unlock() function to enable the Flash option control 
+         register access.
+     (#) Call the following functions to program the desired option bytes.
+         (++) HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit);      
+     (#) Once all needed option bytes to be programmed are correctly written, call the
+         HAL_FLASH_OB_Launch(void) function to launch the Option Bytes programming process.
+     (#) Call the HAL_FLASH_OB_Lock() to disable the Flash option control register access (recommended
+         to protect the option Bytes against possible unwanted operations).
+  
+    [..] Proprietary code Read Out Protection (PcROP):    
+    (#) The PcROP sector is selected by using the same option bytes as the Write
+        protection. As a result, these 2 options are exclusive each other.
+    (#) To activate PCROP mode for Flash sectors(s), you need to follow the sequence below:
+        (++) Use this function HAL_FLASHEx_AdvOBProgram with PCROPState = OB_PCROP_STATE_ENABLE.
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics. 
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the 
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************  
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+
+/** @defgroup FLASH FLASH
+  * @brief FLASH HAL module driver
+  * @{
+  */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @defgroup FLASH_Private_Constants FLASH Private Constants
+  * @{
+  */
+/**
+  * @}
+  */
+
+/* Private macro ---------------------------- ---------------------------------*/
+/** @defgroup FLASH_Private_Macros FLASH Private Macros
+  * @{
+  */
+ 
+/**
+  * @}
+  */
+
+/* Private variables ---------------------------------------------------------*/
+/** @defgroup FLASH_Private_Variables FLASH Private Variables
+  * @{
+  */
+/* Variables used for Erase pages under interruption*/
+FLASH_ProcessTypeDef pFlash;
+/**
+  * @}
+  */
+
+/* Private function prototypes -----------------------------------------------*/
+/** @defgroup FLASH_Private_Functions FLASH Private Functions
+  * @{
+  */
+static  void   FLASH_SetErrorCode(void);
+extern void    FLASH_PageErase(uint32_t PageAddress);
+/**
+  * @}
+  */
+
+/* Exported functions ---------------------------------------------------------*/
+/** @defgroup FLASH_Exported_Functions FLASH Exported Functions
+  * @{
+  */
+  
+/** @defgroup FLASH_Exported_Functions_Group1 Programming operation functions 
+  *  @brief   Programming operation functions 
+  *
+@verbatim   
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Program word at a specified address
+  * @note   To correctly run this function, the HAL_FLASH_Unlock() function
+  *         must be called before.
+  *         Call the HAL_FLASH_Lock() to disable the flash memory access
+  *         (recommended to protect the FLASH memory against possible unwanted operation).
+  *
+  * @param  TypeProgram   Indicate the way to program at a specified address.
+  *                       This parameter can be a value of @ref FLASH_Type_Program
+  * @param  Address       Specifie the address to be programmed.
+  * @param  Data          Specifie the data to be programmed
+  * 
+  * @retval HAL_StatusTypeDef HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint32_t Data)
+{
+  HAL_StatusTypeDef status = HAL_ERROR;
+  
+  /* Process Locked */
+  __HAL_LOCK(&pFlash);
+
+  /* Check the parameters */
+  assert_param(IS_FLASH_TYPEPROGRAM(TypeProgram));
+  assert_param(IS_FLASH_PROGRAM_ADDRESS(Address));
+
+  /* Wait for last operation to be completed */
+  status = FLASH_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+  
+  if(status == HAL_OK)
+  {
+    /* Clean the error context */
+    pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+    /*Program word (32-bit) at a specified address.*/
+    *(__IO uint32_t *)Address = Data;
+
+    /* Wait for last operation to be completed */
+    status = FLASH_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+  }
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(&pFlash);
+
+  return status;
+}
+
+/**
+  * @brief   Program word at a specified address  with interrupt enabled.
+  *
+  * @param  TypeProgram  Indicate the way to program at a specified address.
+  *                      This parameter can be a value of @ref FLASH_Type_Program
+  * @param  Address      Specifie the address to be programmed.
+  * @param  Data         Specifie the data to be programmed
+  * 
+  * @retval HAL_StatusTypeDef HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint32_t Data)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+  
+  /* Process Locked */
+  __HAL_LOCK(&pFlash);
+
+  /* Check the parameters */
+  assert_param(IS_FLASH_TYPEPROGRAM(TypeProgram));
+  assert_param(IS_FLASH_PROGRAM_ADDRESS(Address));
+
+  /* Enable End of FLASH Operation and Error source interrupts */
+  __HAL_FLASH_ENABLE_IT(FLASH_IT_EOP | FLASH_IT_ERR);
+  
+  pFlash.Address = Address;
+  pFlash.ProcedureOnGoing = FLASH_PROC_PROGRAM;
+  /* Clean the error context */
+  pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+  if(TypeProgram == FLASH_TYPEPROGRAM_WORD)
+  {
+    /* Program word (32-bit) at a specified address. */
+    *(__IO uint32_t *)Address = Data;
+  }
+  return status;
+}
+
+/**
+  * @brief This function handles FLASH interrupt request.
+  * @retval None
+  */
+void HAL_FLASH_IRQHandler(void)
+{
+  uint32_t addresstmp = 0;
+  
+  /* Check FLASH operation error flags */
+
+  /* WARNING : On the first cut of STM32L031xx and STM32L041xx devices,
+   *           (RefID = 0x1000) the FLASH_FLAG_OPTVERR bit was not behaving
+   *           as expected. If the user run an application using the first
+   *           cut of the STM32L031xx device or the first cut of the STM32L041xx
+   *           device, the check on the FLASH_FLAG_OPTVERR bit should be ignored.
+   *
+   *           Note :The revId of the device can be retrieved via the HAL_GetREVID()
+   *           function.
+   *
+   */
+
+  if( __HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGAERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_SIZERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_OPTVERR)    || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_RDERR)      || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_FWWERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_NOTZEROERR) )
+  {
+    if(pFlash.ProcedureOnGoing == FLASH_PROC_PAGEERASE)
+    {
+      /* Return the faulty sector */
+      addresstmp = pFlash.Page;
+      pFlash.Page = 0xFFFFFFFFU;
+    }
+    else
+    {
+      /* Return the faulty address */
+      addresstmp = pFlash.Address;
+    }
+    /* Save the Error code */
+    FLASH_SetErrorCode();
+    
+    /* FLASH error interrupt user callback */
+    HAL_FLASH_OperationErrorCallback(addresstmp);
+
+    /* Stop the procedure ongoing */
+    pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
+  }
+
+  /* Check FLASH End of Operation flag  */
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP))
+  {
+    /* Clear FLASH End of Operation pending bit */
+    __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP);
+    
+    /* Process can continue only if no error detected */
+    if(pFlash.ProcedureOnGoing != FLASH_PROC_NONE)
+    {
+      if(pFlash.ProcedureOnGoing == FLASH_PROC_PAGEERASE)
+      {
+        /* Nb of pages to erased can be decreased */
+        pFlash.NbPagesToErase--;
+
+        /* Check if there are still pages to erase */
+        if(pFlash.NbPagesToErase != 0U)
+        {
+          addresstmp = pFlash.Page;
+          /*Indicate user which sector has been erased */
+          HAL_FLASH_EndOfOperationCallback(addresstmp);
+
+          /*Increment sector number*/
+          addresstmp = pFlash.Page + FLASH_PAGE_SIZE;
+          pFlash.Page = addresstmp;
+
+          /* If the erase operation is completed, disable the ERASE Bit */
+          CLEAR_BIT(FLASH->PECR, FLASH_PECR_ERASE);
+
+          FLASH_PageErase(addresstmp);
+        }
+        else
+        {
+          /* No more pages to Erase, user callback can be called. */
+          /* Reset Sector and stop Erase pages procedure */
+          pFlash.Page = addresstmp = 0xFFFFFFFFU;
+          pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
+          /* FLASH EOP interrupt user callback */
+          HAL_FLASH_EndOfOperationCallback(addresstmp);
+        }
+      }
+      else
+      {
+          /* If the program operation is completed, disable the PROG Bit */
+          CLEAR_BIT(FLASH->PECR, FLASH_PECR_PROG);
+
+          /* Program ended. Return the selected address */
+          /* FLASH EOP interrupt user callback */
+          HAL_FLASH_EndOfOperationCallback(pFlash.Address);
+        
+          /* Reset Address and stop Program procedure */
+          pFlash.Address = 0xFFFFFFFFU;
+          pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
+      }
+    }
+  }
+  
+
+  if(pFlash.ProcedureOnGoing == FLASH_PROC_NONE)
+  {
+    /* Operation is completed, disable the PROG and ERASE */
+    CLEAR_BIT(FLASH->PECR, (FLASH_PECR_ERASE | FLASH_PECR_PROG));
+
+    /* Disable End of FLASH Operation and Error source interrupts */
+    __HAL_FLASH_DISABLE_IT(FLASH_IT_EOP | FLASH_IT_ERR);
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(&pFlash);
+  }
+}
+
+/**
+  * @brief  FLASH end of operation interrupt callback
+  * @param  ReturnValue The value saved in this parameter depends on the ongoing procedure
+  *                 - Pages Erase: Address of the page which has been erased 
+  *                    (if 0xFFFFFFFF, it means that all the selected pages have been erased)
+  *                 - Program: Address which was selected for data program
+  * @retval none
+  */
+__weak void HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(ReturnValue);
+
+  /* NOTE : This function Should not be modified, when the callback is needed,
+            the HAL_FLASH_EndOfOperationCallback could be implemented in the user file
+   */ 
+}
+
+/**
+  * @brief  FLASH operation error interrupt callback
+  * @param  ReturnValue The value saved in this parameter depends on the ongoing procedure
+  *                 - Pages Erase: Address of the page which returned an error
+  *                 - Program: Address which was selected for data program
+  * @retval none
+  */
+__weak void HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(ReturnValue);
+
+  /* NOTE : This function Should not be modified, when the callback is needed,
+            the HAL_FLASH_OperationErrorCallback could be implemented in the user file
+   */ 
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Exported_Functions_Group2 Peripheral Control functions 
+ *  @brief   management functions 
+ *
+@verbatim   
+ ===============================================================================
+                      ##### Peripheral Control functions #####
+ ===============================================================================  
+    [..]
+    This subsection provides a set of functions allowing to control the FLASH 
+    memory operations.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Unlock the FLASH control register access
+  * @retval HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_Unlock(void)
+{
+  uint32_t primask_bit;
+
+  /* Unlocking FLASH_PECR register access*/
+  if(HAL_IS_BIT_SET(FLASH->PECR, FLASH_PECR_PELOCK))
+  {
+    /* Disable interrupts to avoid any interruption during unlock sequence */
+    primask_bit = __get_PRIMASK();
+    __disable_irq();
+
+    WRITE_REG(FLASH->PEKEYR, FLASH_PEKEY1);
+    WRITE_REG(FLASH->PEKEYR, FLASH_PEKEY2);
+
+    /* Re-enable the interrupts: restore previous priority mask */
+    __set_PRIMASK(primask_bit);
+
+    if(HAL_IS_BIT_SET(FLASH->PECR, FLASH_PECR_PELOCK))
+    {
+      return HAL_ERROR;
+    }
+  }
+
+  if (HAL_IS_BIT_SET(FLASH->PECR, FLASH_PECR_PRGLOCK))
+  {
+    /* Disable interrupts to avoid any interruption during unlock sequence */
+    primask_bit = __get_PRIMASK();
+    __disable_irq();
+
+    /* Unlocking the program memory access */
+    WRITE_REG(FLASH->PRGKEYR, FLASH_PRGKEY1);
+    WRITE_REG(FLASH->PRGKEYR, FLASH_PRGKEY2);  
+
+    /* Re-enable the interrupts: restore previous priority mask */
+    __set_PRIMASK(primask_bit);
+
+    if (HAL_IS_BIT_SET(FLASH->PECR, FLASH_PECR_PRGLOCK))
+    {
+      return HAL_ERROR;
+    }
+  }
+
+  return HAL_OK; 
+}
+
+/**
+  * @brief  Locks the FLASH control register access
+  * @retval HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_Lock(void)
+{
+  /* Set the PRGLOCK Bit to lock the FLASH Registers access */
+  SET_BIT(FLASH->PECR, FLASH_PECR_PRGLOCK);
+  
+  /* Set the PELOCK Bit to lock the PECR Register access */
+  SET_BIT(FLASH->PECR, FLASH_PECR_PELOCK);
+
+  return HAL_OK;  
+}
+
+/**
+  * @brief  Unlock the FLASH Option Control Registers access.
+  * @retval HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void)
+{
+  uint32_t primask_bit;
+
+  if(HAL_IS_BIT_SET(FLASH->PECR, FLASH_PECR_OPTLOCK))
+  {
+    /* Disable interrupts to avoid any interruption during unlock sequence */
+    primask_bit = __get_PRIMASK();
+    __disable_irq();
+
+    /* Unlocking FLASH_PECR register access*/
+    if(HAL_IS_BIT_SET(FLASH->PECR, FLASH_PECR_PELOCK))
+    {  
+      /* Unlocking FLASH_PECR register access*/
+      WRITE_REG(FLASH->PEKEYR, FLASH_PEKEY1);
+      WRITE_REG(FLASH->PEKEYR, FLASH_PEKEY2);
+    }
+
+    /* Unlocking the option bytes block access */
+    WRITE_REG(FLASH->OPTKEYR, FLASH_OPTKEY1);
+    WRITE_REG(FLASH->OPTKEYR, FLASH_OPTKEY2);
+
+    /* Re-enable the interrupts: restore previous priority mask */
+    __set_PRIMASK(primask_bit);
+  }
+  else
+  {
+    return HAL_ERROR;
+  }  
+  
+  return HAL_OK;  
+}
+
+/**
+  * @brief  Lock the FLASH Option Control Registers access.
+  * @retval HAL Status 
+  */
+HAL_StatusTypeDef HAL_FLASH_OB_Lock(void)
+{
+  /* Set the OPTLOCK Bit to lock the option bytes block access */
+  SET_BIT(FLASH->PECR, FLASH_PECR_OPTLOCK);
+  
+  return HAL_OK;  
+}
+  
+/**
+  * @brief  Launch the option byte loading.
+  * @note   This function will reset automatically the MCU.
+  * @retval HAL Status
+  */
+HAL_StatusTypeDef HAL_FLASH_OB_Launch(void)
+{
+  /* Set the OBL_Launch bit to launch the option byte loading */
+  SET_BIT(FLASH->PECR, FLASH_PECR_OBL_LAUNCH);
+  
+  /* Wait for last operation to be completed */
+  return(FLASH_WaitForLastOperation(FLASH_TIMEOUT_VALUE));
+}
+
+/**
+  * @}
+  */  
+
+/** @defgroup FLASH_Exported_Functions_Group3 Peripheral errors functions 
+ *  @brief    Peripheral errors functions 
+ *
+@verbatim   
+ ===============================================================================
+                      ##### Peripheral Errors functions #####
+ ===============================================================================  
+    [..]
+    This subsection permit to get in run-time errors of  the FLASH peripheral.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Get the specific FLASH error flag.
+  * @retval FLASH_ErrorCode The returned value can be:
+  *            @ref FLASH_Error_Codes
+  */
+uint32_t HAL_FLASH_GetError(void)
+{
+   return pFlash.ErrorCode;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Private_Functions
+ * @{
+ */
+
+/**
+  * @brief  Wait for a FLASH operation to complete.
+  * @param  Timeout  maximum flash operation timeout
+  * @retval HAL Status
+  */
+HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout)
+{
+  /* Wait for the FLASH operation to complete by polling on BUSY flag to be reset.
+     Even if the FLASH operation fails, the BUSY flag will be reset and an error
+     flag will be set */
+     
+  uint32_t tickstart = HAL_GetTick();
+     
+  while(__HAL_FLASH_GET_FLAG(FLASH_FLAG_BSY)) 
+  { 
+    if (Timeout != HAL_MAX_DELAY)
+    {
+      if((Timeout == 0U) || ((HAL_GetTick()-tickstart) > Timeout))
+      {
+        return HAL_TIMEOUT;
+      }
+    }
+  }
+  
+  /* Check FLASH End of Operation flag  */
+  if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP))
+  {
+    /* Clear FLASH End of Operation pending bit */
+    __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP);
+  }
+  
+  if( __HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGAERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_SIZERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_OPTVERR)    || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_RDERR)      || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_FWWERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_NOTZEROERR) )
+  {
+    /*Save the error code*/
+
+    /* WARNING : On the first cut of STM32L031xx and STM32L041xx devices,
+     *           (RefID = 0x1000) the FLASH_FLAG_OPTVERR bit was not behaving
+     *           as expected. If the user run an application using the first
+     *           cut of the STM32L031xx device or the first cut of the STM32L041xx
+     *           device, this error should be ignored. The revId of the device
+     *           can be retrieved via the HAL_GetREVID() function.
+     *
+     */
+    FLASH_SetErrorCode();
+    return HAL_ERROR;
+  }
+
+  /* There is no error flag set */
+  return HAL_OK;
+}
+
+
+/**
+  * @brief  Set the specific FLASH error flag.
+  * @retval None
+  */
+static void FLASH_SetErrorCode(void)
+{
+  uint32_t flags = 0;
+  
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR))
+  {
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_WRP;
+    flags |= FLASH_FLAG_WRPERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGAERR))
+  {
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_PGA;
+    flags |= FLASH_FLAG_PGAERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_SIZERR))
+  { 
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_SIZE;
+    flags |= FLASH_FLAG_SIZERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_OPTVERR))
+  {
+    /* WARNING : On the first cut of STM32L031xx and STM32L041xx devices,
+     *           (RefID = 0x1000) the FLASH_FLAG_OPTVERR bit was not behaving
+     *           as expected. If the user run an application using the first
+     *           cut of the STM32L031xx device or the first cut of the STM32L041xx
+     *           device, this error should be ignored. The revId of the device
+     *           can be retrieved via the HAL_GetREVID() function.
+     *
+     */
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_OPTV;
+    flags |= FLASH_FLAG_OPTVERR;
+  }
+
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_RDERR))
+  {
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_RD;
+    flags |= FLASH_FLAG_RDERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_FWWERR))
+  { 
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_FWWERR;
+    flags |= HAL_FLASH_ERROR_FWWERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_NOTZEROERR))
+  { 
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_NOTZERO;
+    flags |= FLASH_FLAG_NOTZEROERR;
+  }
+
+  /* Clear FLASH error pending bits */
+  __HAL_FLASH_CLEAR_FLAG(flags);
+}  
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_flash_ramfunc.c

@@ -0,0 +1,521 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_flash_ramfunc.c
+  * @author  MCD Application Team
+  * @brief   FLASH RAMFUNC driver.
+  *          This file provides a Flash firmware functions which should be 
+  *          executed from internal SRAM
+  *
+  *  @verbatim
+
+    *** ARM Compiler ***
+    --------------------
+    [..] RAM functions are defined using the toolchain options. 
+         Functions that are be executed in RAM should reside in a separate
+         source module. Using the 'Options for File' dialog you can simply change
+         the 'Code / Const' area of a module to a memory space in physical RAM.
+         Available memory areas are declared in the 'Target' tab of the 
+         Options for Target' dialog.
+
+    *** ICCARM Compiler ***
+    -----------------------
+    [..] RAM functions are defined using a specific toolchain keyword "__ramfunc".
+
+    *** GNU Compiler ***
+    --------------------
+    [..] RAM functions are defined using a specific toolchain attribute
+         "__attribute__((section(".RamFunc")))".
+
+@endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics. 
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the 
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+
+/** @addtogroup FLASH
+  * @{
+  */
+/** @addtogroup FLASH_Private_Variables
+ * @{
+ */
+extern FLASH_ProcessTypeDef pFlash;
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+/** @defgroup FLASH_RAMFUNC FLASH_RAMFUNC
+  * @brief FLASH functions executed from RAM
+  * @{
+  */ 
+
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/** @defgroup FLASH_RAMFUNC_Private_Functions FLASH RAM Private Functions
+ * @{
+ */
+
+static __RAM_FUNC HAL_StatusTypeDef FLASHRAM_WaitForLastOperation(uint32_t Timeout);
+static __RAM_FUNC HAL_StatusTypeDef FLASHRAM_SetErrorCode(void);
+
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+ 
+/** @defgroup FLASH_RAMFUNC_Exported_Functions FLASH RAM Exported Functions
+ *
+@verbatim  
+ ===============================================================================
+                      ##### ramfunc functions #####
+ ===============================================================================  
+    [..]
+    This subsection provides a set of functions that should be executed from RAM 
+    transfers.
+
+@endverbatim
+  * @{
+  */ 
+
+/** @defgroup FLASH_RAMFUNC_Exported_Functions_Group1 Peripheral features functions 
+  * @{
+  */  
+
+/**
+  * @brief  Enable  the power down mode during RUN mode.
+  * @note  This function can be used only when the user code is running from Internal SRAM.
+  * @retval HAL status
+  */
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_EnableRunPowerDown(void)
+{
+  /* Enable the Power Down in Run mode*/
+  __HAL_FLASH_POWER_DOWN_ENABLE();
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Disable the power down mode during RUN mode.
+  * @note  This function can be used only when the user code is running from Internal SRAM.
+  * @retval HAL status
+  */
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_DisableRunPowerDown(void)
+{
+  /* Disable the Power Down in Run mode*/
+  __HAL_FLASH_POWER_DOWN_DISABLE();
+
+  return HAL_OK;  
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_RAMFUNC_Exported_Functions_Group2 Programming and erasing operation functions 
+ *
+@verbatim  
+@endverbatim
+  * @{
+  */
+
+#if defined(FLASH_PECR_PARALLBANK)
+/**
+  * @brief  Erases a specified 2 pages in program memory in parallel.
+  * @note   This function can be used only for STM32L07xxx/STM32L08xxx  devices.
+  *         To correctly run this function, the @ref HAL_FLASH_Unlock() function
+  *         must be called before.
+  *         Call the @ref HAL_FLASH_Lock() to disable the flash memory access 
+  *        (recommended to protect the FLASH memory against possible unwanted operation).
+  * @param  Page_Address1: The page address in program memory to be erased in 
+  *         the first Bank (BANK1). This parameter should be between FLASH_BASE
+  *         and FLASH_BANK1_END.
+  * @param  Page_Address2: The page address in program memory to be erased in 
+  *         the second Bank (BANK2). This parameter should be between FLASH_BANK2_BASE
+  *         and FLASH_BANK2_END.
+  * @note   A Page is erased in the Program memory only if the address to load 
+  *         is the start address of a page (multiple of @ref FLASH_PAGE_SIZE bytes).
+  * @retval HAL status
+  */
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_EraseParallelPage(uint32_t Page_Address1, uint32_t Page_Address2)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  /* Wait for last operation to be completed */
+  status = FLASHRAM_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+  
+  if(status == HAL_OK)
+  {
+    /* Proceed to erase the page */
+    SET_BIT(FLASH->PECR, FLASH_PECR_PARALLBANK);
+    SET_BIT(FLASH->PECR, FLASH_PECR_ERASE);
+    SET_BIT(FLASH->PECR, FLASH_PECR_PROG);
+  
+    /* Write 00000000h to the first word of the first program page to erase */
+    *(__IO uint32_t *)Page_Address1 = 0x00000000U;
+    /* Write 00000000h to the first word of the second program page to erase */    
+    *(__IO uint32_t *)Page_Address2 = 0x00000000U;
+ 
+    /* Wait for last operation to be completed */
+    status = FLASHRAM_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+
+    /* If the erase operation is completed, disable the ERASE, PROG and PARALLBANK bits */
+    CLEAR_BIT(FLASH->PECR, FLASH_PECR_PROG);
+    CLEAR_BIT(FLASH->PECR, FLASH_PECR_ERASE);
+    CLEAR_BIT(FLASH->PECR, FLASH_PECR_PARALLBANK);
+  }     
+  /* Return the Erase Status */
+  return status;
+}
+
+/**
+  * @brief  Program 2 half pages in program memory in parallel (half page size is 16 Words).
+  * @note   This function can be used only for STM32L07xxx/STM32L08xxx  devices.
+  * @param  Address1: specifies the first address to be written in the first bank 
+  *        (BANK1). This parameter should be between FLASH_BASE and (FLASH_BANK1_END - FLASH_PAGE_SIZE).
+  * @param  pBuffer1: pointer to the buffer  containing the data to be  written 
+  *         to the first half page in the first bank.
+  * @param  Address2: specifies the second address to be written in the second bank
+  *        (BANK2). This parameter should be between FLASH_BANK2_BASE and (FLASH_BANK2_END - FLASH_PAGE_SIZE).
+  * @param  pBuffer2: pointer to the buffer containing the data to be  written 
+  *         to the second half page in the second bank.
+  * @note   To correctly run this function, the @ref HAL_FLASH_Unlock() function
+  *         must be called before.
+  *         Call the @ref HAL_FLASH_Lock() to disable the flash memory access  
+  *         (recommended to protect the FLASH memory against possible unwanted operation).
+  * @note   Half page write is possible only from SRAM.
+  * @note   A half page is written to the program memory only if the first 
+  *         address to load is the start address of a half page (multiple of 64 
+  *         bytes) and the 15 remaining words to load are in the same half page.
+  * @note   During the Program memory half page write all read operations are 
+  *         forbidden (this includes DMA read operations and debugger read 
+  *         operations such as breakpoints, periodic updates, etc.).
+  * @note   If a PGAERR is set during a Program memory half page write, the 
+  *         complete write operation is aborted. Software should then reset the 
+  *         FPRG and PROG/DATA bits and restart the write operation from the 
+  *         beginning.
+  * @retval HAL status
+  */
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_ProgramParallelHalfPage(uint32_t Address1, uint32_t* pBuffer1, uint32_t Address2, uint32_t* pBuffer2)
+{
+  uint32_t count = 0U; 
+  HAL_StatusTypeDef status = HAL_OK;
+
+  /* Wait for last operation to be completed */
+  status = FLASHRAM_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+  
+  if(status == HAL_OK)
+  {
+    /* Proceed to program the new half page */
+    SET_BIT(FLASH->PECR, FLASH_PECR_PARALLBANK);
+    SET_BIT(FLASH->PECR, FLASH_PECR_FPRG);
+    SET_BIT(FLASH->PECR, FLASH_PECR_PROG);
+
+    /* Wait for last operation to be completed */
+    status = FLASHRAM_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+    if(status == HAL_OK)
+    {
+      /* Disable all IRQs */
+      __disable_irq();
+
+      /* Write the first half page directly with 16 different words */
+      while(count < 16U)
+      {
+        /* Address1 doesn't need to be increased */ 
+        *(__IO uint32_t*) Address1 = *pBuffer1;
+        pBuffer1++;
+        count ++;  
+      }
+
+      /* Write the second half page directly with 16 different words */
+      count = 0U;
+      while(count < 16U)
+      {
+        /* Address2 doesn't need to be increased */ 
+        *(__IO uint32_t*) Address2 = *pBuffer2;
+        pBuffer2++;
+        count ++;  
+      }
+
+      /* Enable IRQs */
+      __enable_irq();
+
+      /* Wait for last operation to be completed */
+      status = FLASHRAM_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+    }
+
+    /* if the write operation is completed, disable the PROG, FPRG and PARALLBANK bits */
+    CLEAR_BIT(FLASH->PECR, FLASH_PECR_PROG);
+    CLEAR_BIT(FLASH->PECR, FLASH_PECR_FPRG);
+    CLEAR_BIT(FLASH->PECR, FLASH_PECR_PARALLBANK);
+  }
+
+  /* Return the Write Status */
+  return status;
+}
+#endif /* FLASH_PECR_PARALLBANK */
+
+/**
+  * @brief  Program a half page in program memory.
+  * @param  Address specifies the address to be written.
+  * @param  pBuffer pointer to the buffer  containing the data to be  written to 
+  *         the half page.
+  * @note   To correctly run this function, the @ref HAL_FLASH_Unlock() function
+  *         must be called before.
+  *         Call the @ref HAL_FLASH_Lock() to disable the flash memory access  
+  *         (recommended to protect the FLASH memory against possible unwanted operation)
+  * @note   Half page write is possible only from SRAM.
+  * @note   A half page is written to the program memory only if the first 
+  *         address to load is the start address of a half page (multiple of 64 
+  *         bytes) and the 15 remaining words to load are in the same half page.
+  * @note   During the Program memory half page write all read operations are 
+  *         forbidden (this includes DMA read operations and debugger read 
+  *         operations such as breakpoints, periodic updates, etc.).
+  * @note   If a PGAERR is set during a Program memory half page write, the 
+  *         complete write operation is aborted. Software should then reset the 
+  *         FPRG and PROG/DATA bits and restart the write operation from the 
+  *         beginning.
+  * @retval HAL status
+  */
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_HalfPageProgram(uint32_t Address, uint32_t* pBuffer)
+{
+  uint32_t count = 0U; 
+  HAL_StatusTypeDef status = HAL_OK;
+
+  /* Wait for last operation to be completed */
+  status = FLASHRAM_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+  
+  if(status == HAL_OK)
+  {
+    /* Proceed to program the new half page */
+    SET_BIT(FLASH->PECR, FLASH_PECR_FPRG);
+    SET_BIT(FLASH->PECR, FLASH_PECR_PROG);
+    
+    /* Disable all IRQs */
+    __disable_irq();
+
+    /* Write one half page directly with 16 different words */
+    while(count < 16U)
+    {
+      /* Address doesn't need to be increased */ 
+      *(__IO uint32_t*) Address = *pBuffer;
+      pBuffer++;
+      count ++;  
+    }
+
+    /* Enable IRQs */
+    __enable_irq();
+
+    /* Wait for last operation to be completed */
+    status = FLASHRAM_WaitForLastOperation(FLASH_TIMEOUT_VALUE);
+ 
+    /* If the write operation is completed, disable the PROG and FPRG bits */
+    CLEAR_BIT(FLASH->PECR, FLASH_PECR_PROG);
+    CLEAR_BIT(FLASH->PECR, FLASH_PECR_FPRG);
+  }
+
+  /* Return the Write Status */
+  return status;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_RAMFUNC_Exported_Functions_Group3 Peripheral errors functions 
+ *  @brief    Peripheral errors functions 
+ *
+@verbatim   
+ ===============================================================================
+                      ##### Peripheral errors functions #####
+ ===============================================================================  
+    [..]
+    This subsection permit to get in run-time errors of  the FLASH peripheral.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Get the specific FLASH errors flag.
+  * @param  Error pointer is the error value. It can be a mixed of:
+  *            @arg @ref HAL_FLASH_ERROR_RD      FLASH Read Protection error flag (PCROP)
+  *            @arg @ref HAL_FLASH_ERROR_SIZE    FLASH Programming Parallelism error flag  
+  *            @arg @ref HAL_FLASH_ERROR_PGA     FLASH Programming Alignment error flag
+  *            @arg @ref HAL_FLASH_ERROR_WRP     FLASH Write protected error flag
+  *            @arg @ref HAL_FLASH_ERROR_OPTV    FLASH Option valid error flag 
+  *            @arg @ref HAL_FLASH_ERROR_FWWERR  FLASH Write or Erase operation aborted
+  *            @arg @ref HAL_FLASH_ERROR_NOTZERO FLASH Write operation is done in a not-erased region
+  * @retval HAL Status
+  */
+__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_GetError(uint32_t * Error)
+{ 
+  *Error = pFlash.ErrorCode;
+  return HAL_OK;  
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_RAMFUNC_Private_Functions
+  * @{
+  */ 
+
+/**
+  * @brief  Set the specific FLASH error flag.
+  * @retval HAL Status
+  */
+static __RAM_FUNC HAL_StatusTypeDef FLASHRAM_SetErrorCode(void)
+{
+  uint32_t flags = 0;
+  
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR))
+  {
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_WRP;
+    flags |= FLASH_FLAG_WRPERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_PGAERR))
+  {
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_PGA;
+    flags |= FLASH_FLAG_PGAERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_SIZERR))
+  { 
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_SIZE;
+    flags |= FLASH_FLAG_SIZERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_OPTVERR))
+  {
+    /* WARNING : On the first cut of STM32L031xx and STM32L041xx devices,
+     *           (RefID = 0x1000) the FLASH_FLAG_OPTVERR bit was not behaving
+     *           as expected. If the user run an application using the first
+     *           cut of the STM32L031xx device or the first cut of the STM32L041xx
+     *           device, this error should be ignored. The revId of the device
+     *           can be retrieved via the HAL_GetREVID() function.
+     *
+     */
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_OPTV;
+    flags |= FLASH_FLAG_OPTVERR;
+  }
+
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_RDERR))
+  {
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_RD;
+    flags |= FLASH_FLAG_RDERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_FWWERR))
+  { 
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_FWWERR;
+    flags |= HAL_FLASH_ERROR_FWWERR;
+  }
+  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_NOTZEROERR))
+  { 
+    pFlash.ErrorCode |= HAL_FLASH_ERROR_NOTZERO;
+    flags |= FLASH_FLAG_NOTZEROERR;
+  }
+
+  /* Clear FLASH error pending bits */
+  __HAL_FLASH_CLEAR_FLAG(flags);
+
+  return HAL_OK;
+}  
+
+/**
+  * @brief  Wait for a FLASH operation to complete.
+  * @param  Timeout maximum flash operationtimeout
+  * @retval HAL status
+  */
+static __RAM_FUNC HAL_StatusTypeDef FLASHRAM_WaitForLastOperation(uint32_t Timeout)
+{ 
+    /* Wait for the FLASH operation to complete by polling on BUSY flag to be reset.
+       Even if the FLASH operation fails, the BUSY flag will be reset and an error
+       flag will be set */
+       
+    while(__HAL_FLASH_GET_FLAG(FLASH_FLAG_BSY) && (Timeout != 0x00U)) 
+    { 
+      Timeout--;
+    }
+    
+    if(Timeout == 0x00U)
+    {
+      return HAL_TIMEOUT;
+    }
+    
+  /* Check FLASH End of Operation flag  */
+  if (__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP))
+  {
+    /* Clear FLASH End of Operation pending bit */
+    __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP);
+  }
+  
+  if( __HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGAERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_SIZERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_OPTVERR)    || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_RDERR)      || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_FWWERR)     || 
+      __HAL_FLASH_GET_FLAG(FLASH_FLAG_NOTZEROERR) )
+  {
+    /*Save the error code*/
+
+    /* WARNING : On the first cut of STM32L031xx and STM32L041xx devices,
+     *           (RefID = 0x1000) the FLASH_FLAG_OPTVERR bit was not behaving
+     *           as expected. If the user run an application using the first
+     *           cut of the STM32L031xx device or the first cut of the STM32L041xx
+     *           device, this error should be ignored. The revId of the device
+     *           can be retrieved via the HAL_GetREVID() function.
+     *
+     */
+    FLASHRAM_SetErrorCode();
+    return HAL_ERROR;
+  }
+
+  /* There is no error flag set */
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_FLASH_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+     
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_gpio.c

@@ -0,0 +1,532 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_gpio.c
+  * @author  MCD Application Team
+  * @brief   GPIO HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the General Purpose Input/Output (GPIO) peripheral:
+  *           + Initialization and de-initialization functions
+  *           + IO operation functions
+  *
+  @verbatim
+  ==============================================================================
+                    ##### GPIO Peripheral features #####
+  ==============================================================================
+  [..]
+    (+) Each port bit of the general-purpose I/O (GPIO) ports can be individually
+  configured by software in several modes:
+        (++) Input mode
+        (++) Analog mode
+        (++) Output mode
+        (++) Alternate function mode
+        (++) External interrupt/event lines
+
+    (+) During and just after reset, the alternate functions and external interrupt
+  lines are not active and the I/O ports are configured in input floating mode.
+
+    (+) All GPIO pins have weak internal pull-up and pull-down resistors, which can be
+  activated or not.
+
+    (+) In Output or Alternate mode, each IO can be configured on open-drain or push-pull
+  type and the IO speed can be selected depending on the VDD value.
+
+    (+) The microcontroller IO pins are connected to onboard peripherals/modules through a
+        multiplexer that allows only one peripheral alternate function (AF) connected
+  to an IO pin at a time. In this way, there can be no conflict between peripherals
+  sharing the same IO pin.
+
+    (+) All ports have external interrupt/event capability. To use external interrupt
+  lines, the port must be configured in input mode. All available GPIO pins are
+  connected to the 16 external interrupt/event lines from EXTI0 to EXTI15.
+
+    (+) The external interrupt/event controller consists of up to 28 edge detectors
+  (16 lines are connected to GPIO) for generating event/interrupt requests (each
+  input line can be independently configured to select the type (interrupt or event)
+  and the corresponding trigger event (rising or falling or both). Each line can
+  also be masked independently.
+
+                     ##### How to use this driver #####
+  ==============================================================================
+  [..]
+    (#) Enable the GPIO IOPORT clock using the following function: __HAL_RCC_GPIOx_CLK_ENABLE().
+
+    (#) Configure the GPIO pin(s) using HAL_GPIO_Init().
+        (++) Configure the IO mode using "Mode" member from GPIO_InitTypeDef structure
+        (++) Activate Pull-up, Pull-down resistor using "Pull" member from GPIO_InitTypeDef
+             structure.
+        (++) In case of Output or alternate function mode selection: the speed is
+             configured through "Speed" member from GPIO_InitTypeDef structure.
+        (++) In alternate mode is selection, the alternate function connected to the IO
+             is configured through "Alternate" member from GPIO_InitTypeDef structure.
+        (++) Analog mode is required when a pin is to be used as ADC channel
+             or DAC output.
+        (++) In case of external interrupt/event selection the "Mode" member from
+             GPIO_InitTypeDef structure select the type (interrupt or event) and
+             the corresponding trigger event (rising or falling or both).
+
+    (#) In case of external interrupt/event mode selection, configure NVIC IRQ priority
+        mapped to the EXTI line using HAL_NVIC_SetPriority() and enable it using
+        HAL_NVIC_EnableIRQ().
+
+   (#) HAL_GPIO_DeInit allows to set register values to their reset value. This function
+       is also to be used when unconfiguring pin which was used as an external interrupt
+       or in event mode. That is the only way to reset the corresponding bit in
+       EXTI & SYSCFG registers.
+
+    (#) To get the level of a pin configured in input mode use HAL_GPIO_ReadPin().
+
+    (#) To set/reset the level of a pin configured in output mode use
+        HAL_GPIO_WritePin()/HAL_GPIO_TogglePin().
+
+    (#) To lock pin configuration until next reset use HAL_GPIO_LockPin().
+
+    (#) During and just after reset, the alternate functions are not
+        active and the GPIO pins are configured in input floating mode (except JTAG
+        pins).
+
+    (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general purpose
+        (PC14 and PC15, respectively) when the LSE oscillator is off. The LSE has
+        priority over the GPIO function.
+
+    (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as
+        general purpose PH0 and PH1, respectively, when the HSE oscillator is off.
+        The HSE has priority over the GPIO function.
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+
+/** @addtogroup GPIO
+  * @brief GPIO HAL module driver
+  * @{
+  */
+
+/* Private define ------------------------------------------------------------*/
+/** @addtogroup GPIO_Private
+  * @{
+  */
+#define GPIO_NUMBER           (16U)
+/**
+  * @}
+  */
+/** @addtogroup GPIO_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup GPIO_Exported_Functions_Group1
+ *  @brief    Initialization and de-initialization functions
+ *
+@verbatim
+ ===============================================================================
+              ##### Initialization and de-initialization functions #####
+ ===============================================================================
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Initializes the GPIOx peripheral according to the specified parameters in the GPIO_Init.
+  * @param  GPIOx where x can be (A..E and H) to select the GPIO peripheral for STM32L0XX family devices.
+  *                Note that GPIOE is not available on all devices.
+  * @param  GPIO_Init pointer to a GPIO_InitTypeDef structure that contains
+  *                    the configuration information for the specified GPIO peripheral.
+  * @retval None
+  */
+void HAL_GPIO_Init(GPIO_TypeDef  *GPIOx, GPIO_InitTypeDef *GPIO_Init)
+{
+  uint32_t position = 0x00U;
+  uint32_t iocurrent = 0x00U;
+  uint32_t temp = 0x00U;
+
+  /* Check the parameters */
+  assert_param(IS_GPIO_MODE(GPIO_Init->Mode));
+  assert_param(IS_GPIO_PIN_AVAILABLE(GPIOx, (GPIO_Init->Pin)));
+
+  /* Configure the port pins */
+  while (((GPIO_Init->Pin) >> position) != 0)
+  {
+    /* Get the IO position */
+    iocurrent = (GPIO_Init->Pin) & (1U << position);
+
+    if (iocurrent)
+    {
+      /*--------------------- GPIO Mode Configuration ------------------------*/
+      /* In case of Output or Alternate function mode selection */
+      if (((GPIO_Init->Mode & GPIO_MODE) == MODE_OUTPUT) ||
+          ((GPIO_Init->Mode & GPIO_MODE) == MODE_AF))
+      {
+        /* Check the Speed parameter */
+        assert_param(IS_GPIO_SPEED(GPIO_Init->Speed));
+        /* Configure the IO Speed */
+        temp = GPIOx->OSPEEDR;
+        temp &= ~(GPIO_OSPEEDER_OSPEED0 << (position * 2U));
+        temp |= (GPIO_Init->Speed << (position * 2U));
+        GPIOx->OSPEEDR = temp;
+
+        /* Configure the IO Output Type */
+        temp = GPIOx->OTYPER;
+        temp &= ~(GPIO_OTYPER_OT_0 << position) ;
+        temp |= (((GPIO_Init->Mode & OUTPUT_TYPE) >> OUTPUT_TYPE_Pos) << position);
+        GPIOx->OTYPER = temp;
+      }
+
+      if ((GPIO_Init->Mode & GPIO_MODE) != MODE_ANALOG)
+      {
+        /* Check the Pull parameter */
+        assert_param(IS_GPIO_PULL(GPIO_Init->Pull));
+
+        /* Activate the Pull-up or Pull down resistor for the current IO */
+        temp = GPIOx->PUPDR;
+        temp &= ~(GPIO_PUPDR_PUPD0 << (position * 2U));
+        temp |= ((GPIO_Init->Pull) << (position * 2U));
+        GPIOx->PUPDR = temp;
+      }
+
+      /* In case of Alternate function mode selection */
+      if ((GPIO_Init->Mode & GPIO_MODE) == MODE_AF)
+      {
+        /* Check the Alternate function parameters */
+        assert_param(IS_GPIO_AF_INSTANCE(GPIOx));
+        assert_param(IS_GPIO_AF(GPIO_Init->Alternate));
+
+        /* Configure Alternate function mapped with the current IO */
+        temp = GPIOx->AFR[position >> 3U];
+        temp &= ~(0xFUL << ((uint32_t)(position & 0x07UL) * 4U));
+        temp |= ((uint32_t)(GPIO_Init->Alternate) << (((uint32_t)position & (uint32_t)0x07U) * 4U));
+        GPIOx->AFR[position >> 3U] = temp;
+      }
+
+      /* Configure IO Direction mode (Input, Output, Alternate or Analog) */
+      temp = GPIOx->MODER;
+      temp &= ~(GPIO_MODER_MODE0 << (position * 2U));
+      temp |= ((GPIO_Init->Mode & GPIO_MODE) << (position * 2U));
+      GPIOx->MODER = temp;
+
+      /*--------------------- EXTI Mode Configuration ------------------------*/
+      /* Configure the External Interrupt or event for the current IO */
+      if ((GPIO_Init->Mode & EXTI_MODE) != 0x00U)
+      {
+        /* Enable SYSCFG Clock */
+        __HAL_RCC_SYSCFG_CLK_ENABLE();
+
+        temp = SYSCFG->EXTICR[position >> 2U];
+        CLEAR_BIT(temp, (0x0FUL) << (4U * (position & 0x03U)));
+        SET_BIT(temp, (GPIO_GET_INDEX(GPIOx)) << (4 * (position & 0x03U)));
+        SYSCFG->EXTICR[position >> 2U] = temp;
+
+        /* Clear EXTI line configuration */
+        temp = EXTI->IMR;
+        temp &= ~((uint32_t)iocurrent);
+        if ((GPIO_Init->Mode & EXTI_IT) != 0x00U)
+        {
+          temp |= iocurrent;
+        }
+        EXTI->IMR = temp;
+
+        temp = EXTI->EMR;
+        temp &= ~((uint32_t)iocurrent);
+        if ((GPIO_Init->Mode & EXTI_EVT) != 0x00U)
+        {
+          temp |= iocurrent;
+        }
+        EXTI->EMR = temp;
+
+        /* Clear Rising Falling edge configuration */
+        temp = EXTI->RTSR;
+        temp &= ~((uint32_t)iocurrent);
+        if ((GPIO_Init->Mode & TRIGGER_RISING) != 0x00U)
+        {
+          temp |= iocurrent;
+        }
+        EXTI->RTSR = temp;
+
+        temp = EXTI->FTSR;
+        temp &= ~((uint32_t)iocurrent);
+        if ((GPIO_Init->Mode & TRIGGER_FALLING) != 0x00U)
+        {
+          temp |= iocurrent;
+        }
+        EXTI->FTSR = temp;
+      }
+    }
+    position++;
+  }
+}
+
+/**
+  * @brief  De-initializes the GPIOx peripheral registers to their default reset values.
+  * @param  GPIOx where x can be (A..E and H) to select the GPIO peripheral for STM32L0XX family devices.
+  *                Note that GPIOE is not available on all devices.
+  * @param  GPIO_Pin specifies the port bit to be written.
+  *                   This parameter can be one of GPIO_PIN_x where x can be (0..15).
+  *                   All port bits are not necessarily available on all GPIOs.
+  * @retval None
+  */
+void HAL_GPIO_DeInit(GPIO_TypeDef  *GPIOx, uint32_t GPIO_Pin)
+{
+  uint32_t position = 0x00U;
+  uint32_t iocurrent = 0x00U;
+  uint32_t tmp = 0x00U;
+
+  /* Check the parameters */
+  assert_param(IS_GPIO_PIN_AVAILABLE(GPIOx, GPIO_Pin));
+
+  /* Configure the port pins */
+  while ((GPIO_Pin >> position) != 0)
+  {
+    /* Get the IO position */
+    iocurrent = (GPIO_Pin) & (1U << position);
+
+    if (iocurrent)
+    {
+      /*------------------------- EXTI Mode Configuration --------------------*/
+      /* Clear the External Interrupt or Event for the current IO */
+
+      tmp = SYSCFG->EXTICR[position >> 2U];
+      tmp &= ((0x0FUL) << (4U * (position & 0x03U)));
+      if (tmp == (GPIO_GET_INDEX(GPIOx) << (4U * (position & 0x03U))))
+      {
+        /* Clear EXTI line configuration */
+        EXTI->IMR &= ~((uint32_t)iocurrent);
+        EXTI->EMR &= ~((uint32_t)iocurrent);
+
+        /* Clear Rising Falling edge configuration */
+        EXTI->RTSR &= ~((uint32_t)iocurrent);
+        EXTI->FTSR &= ~((uint32_t)iocurrent);
+        
+        tmp = (0x0FUL) << (4U * (position & 0x03U));
+        SYSCFG->EXTICR[position >> 2U] &= ~tmp;
+      }
+
+      /*------------------------- GPIO Mode Configuration --------------------*/
+      /* Configure IO Direction in Input Floting Mode */
+      GPIOx->MODER |= (GPIO_MODER_MODE0 << (position * 2U));
+
+      /* Configure the default Alternate Function in current IO */
+      GPIOx->AFR[position >> 3U] &= ~(0xFUL << ((uint32_t)(position & 0x07UL) * 4U));
+
+      /* Deactivate the Pull-up oand Pull-down resistor for the current IO */
+      GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPD0 << (position * 2U));
+
+      /* Configure the default value IO Output Type */
+      GPIOx->OTYPER  &= ~(GPIO_OTYPER_OT_0 << position);
+
+      /* Configure the default value for IO Speed */
+      GPIOx->OSPEEDR &= ~(GPIO_OSPEEDER_OSPEED0 << (position * 2U));
+    }
+    position++;
+  }
+}
+
+/**
+  * @}
+  */
+
+/** @addtogroup GPIO_Exported_Functions_Group2
+ *  @brief   GPIO Read and Write
+ *
+@verbatim
+ ===============================================================================
+                       ##### IO operation functions #####
+ ===============================================================================
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Reads the specified input port pin.
+  * @param  GPIOx where x can be (A..E and H) to select the GPIO peripheral for STM32L0xx family devices.
+  *                Note that GPIOE is not available on all devices.
+  * @param  GPIO_Pin specifies the port bit to read.
+  *                   This parameter can be GPIO_PIN_x where x can be (0..15).
+  *                   All port bits are not necessarily available on all GPIOs.
+  * @retval The input port pin value.
+  */
+GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin)
+{
+  GPIO_PinState bitstatus;
+
+  /* Check the parameters */
+  assert_param(IS_GPIO_PIN_AVAILABLE(GPIOx, GPIO_Pin));
+
+  if ((GPIOx->IDR & GPIO_Pin) != (uint32_t)GPIO_PIN_RESET)
+  {
+    bitstatus = GPIO_PIN_SET;
+  }
+  else
+  {
+    bitstatus = GPIO_PIN_RESET;
+  }
+  return bitstatus;
+}
+
+/**
+  * @brief  Sets or clears the selected data port bit.
+  *
+  * @note   This function uses GPIOx_BSRR register to allow atomic read/modify
+  *         accesses. In this way, there is no risk of an IRQ occurring between
+  *         the read and the modify access.
+  *
+  * @param  GPIOx where x can be (A..E and H) to select the GPIO peripheral for STM32L0xx family devices.
+  *                Note that GPIOE is not available on all devices.
+  * @param  GPIO_Pin specifies the port bit to be written.
+  *                   This parameter can be one of GPIO_PIN_x where x can be (0..15).
+  *                   All port bits are not necessarily available on all GPIOs.
+  * @param  PinState specifies the value to be written to the selected bit.
+  *                   This parameter can be one of the GPIO_PinState enum values:
+  *                        GPIO_PIN_RESET: to clear the port pin
+  *                        GPIO_PIN_SET: to set the port pin
+  * @retval None
+  */
+void HAL_GPIO_WritePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState)
+{
+  /* Check the parameters */
+  assert_param(IS_GPIO_PIN_AVAILABLE(GPIOx, GPIO_Pin));
+  assert_param(IS_GPIO_PIN_ACTION(PinState));
+
+  if (PinState != GPIO_PIN_RESET)
+  {
+    GPIOx->BSRR = GPIO_Pin;
+  }
+  else
+  {
+    GPIOx->BRR = GPIO_Pin ;
+  }
+}
+
+/**
+  * @brief  Toggles the specified GPIO pins.
+  * @param  GPIOx Where x can be (A..E and H) to select the GPIO peripheral for STM32L0xx family devices.
+  *                Note that GPIOE is not available on all devices.
+  *                All port bits are not necessarily available on all GPIOs.
+  * @param  GPIO_Pin Specifies the pins to be toggled.
+  * @retval None
+  */
+void HAL_GPIO_TogglePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin)
+{
+  uint32_t odr;
+
+  /* Check the parameters */
+  assert_param(IS_GPIO_PIN_AVAILABLE(GPIOx, GPIO_Pin));
+
+  /* get current Ouput Data Register value */
+  odr = GPIOx->ODR;
+
+  /* Set selected pins that were at low level, and reset ones that were high */
+  GPIOx->BSRR = ((odr & GPIO_Pin) << GPIO_NUMBER) | (~odr & GPIO_Pin);
+}
+
+/**
+* @brief  Locks GPIO Pins configuration registers.
+* @note   The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR,
+*         GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH.
+* @note   The configuration of the locked GPIO pins can no longer be modified
+*         until the next reset.
+* @param  GPIOx where x can be (A..E and H) to select the GPIO peripheral for STM32L0xx family.
+*                Note that GPIOE is not available on all devices.
+* @param  GPIO_Pin specifies the port bit to be locked.
+*         This parameter can be any combination of GPIO_Pin_x where x can be (0..15).
+*         All port bits are not necessarily available on all GPIOs.
+* @retval None
+*/
+HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin)
+{
+  __IO uint32_t tmp = GPIO_LCKR_LCKK;
+
+  /* Check the parameters */
+  assert_param(IS_GPIO_PIN_AVAILABLE(GPIOx, GPIO_Pin));
+
+  /* Apply lock key write sequence */
+  tmp |= GPIO_Pin;
+  /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */
+  GPIOx->LCKR = tmp;
+  /* Reset LCKx bit(s): LCKK='0' + LCK[15-0] */
+  GPIOx->LCKR = GPIO_Pin;
+  /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */
+  GPIOx->LCKR = tmp;
+  /* Read LCKK register. This read is mandatory to complete key lock sequence */
+  tmp = GPIOx->LCKR;
+
+  /* read again in order to confirm lock is active */
+  if ((GPIOx->LCKR & GPIO_LCKR_LCKK) != RESET)
+  {
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_ERROR;
+  }
+}
+/**
+  * @brief  This function handles EXTI interrupt request.
+  * @param  GPIO_Pin Specifies the pins connected to the EXTI line.
+  * @retval None
+  */
+void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin)
+{
+  /* EXTI line interrupt detected */
+  if (__HAL_GPIO_EXTI_GET_IT(GPIO_Pin) != RESET)
+  {
+    __HAL_GPIO_EXTI_CLEAR_IT(GPIO_Pin);
+    HAL_GPIO_EXTI_Callback(GPIO_Pin);
+  }
+}
+
+/**
+  * @brief  EXTI line detection callbacks.
+  * @param  GPIO_Pin Specifies the pins connected to the EXTI line.
+  * @retval None
+  */
+__weak void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(GPIO_Pin);
+
+  /* NOTE: This function Should not be modified, when the callback is needed,
+           the HAL_GPIO_EXTI_Callback could be implemented in the user file
+   */
+}
+
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_i2c_ex.c

@@ -0,0 +1,369 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_i2c_ex.c
+  * @author  MCD Application Team
+  * @brief   I2C Extended HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of I2C Extended peripheral:
+  *           + Filter Mode Functions
+  *           + WakeUp Mode Functions
+  *           + FastModePlus Functions
+  *
+  @verbatim
+  ==============================================================================
+               ##### I2C peripheral Extended features  #####
+  ==============================================================================
+
+  [..] Comparing to other previous devices, the I2C interface for STM32L0xx
+       devices contains the following additional features
+
+       (+) Possibility to disable or enable Analog Noise Filter
+       (+) Use of a configured Digital Noise Filter
+       (+) Disable or enable wakeup from Stop mode(s)
+       (+) Disable or enable Fast Mode Plus
+
+                     ##### How to use this driver #####
+  ==============================================================================
+  [..] This driver provides functions to configure Noise Filter and Wake Up Feature
+    (#) Configure I2C Analog noise filter using the function HAL_I2CEx_ConfigAnalogFilter()
+    (#) Configure I2C Digital noise filter using the function HAL_I2CEx_ConfigDigitalFilter()
+    (#) Configure the enable or disable of I2C Wake Up Mode using the functions :
+          (++) HAL_I2CEx_EnableWakeUp()
+          (++) HAL_I2CEx_DisableWakeUp()
+    (#) Configure the enable or disable of fast mode plus driving capability using the functions :
+          (++) HAL_I2CEx_EnableFastModePlus()
+          (++) HAL_I2CEx_DisableFastModePlus()
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup I2CEx I2CEx
+  * @brief I2C Extended HAL module driver
+  * @{
+  */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup I2CEx_Exported_Functions I2C Extended Exported Functions
+  * @{
+  */
+
+/** @defgroup I2CEx_Exported_Functions_Group1 Filter Mode Functions
+  * @brief    Filter Mode Functions
+  *
+@verbatim
+ ===============================================================================
+                      ##### Filter Mode Functions #####
+ ===============================================================================
+    [..] This section provides functions allowing to:
+      (+) Configure Noise Filters
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Configure I2C Analog noise filter.
+  * @param  hi2c Pointer to a I2C_HandleTypeDef structure that contains
+  *                the configuration information for the specified I2Cx peripheral.
+  * @param  AnalogFilter New state of the Analog filter.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_I2CEx_ConfigAnalogFilter(I2C_HandleTypeDef *hi2c, uint32_t AnalogFilter)
+{
+  /* Check the parameters */
+  assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance));
+  assert_param(IS_I2C_ANALOG_FILTER(AnalogFilter));
+
+  if (hi2c->State == HAL_I2C_STATE_READY)
+  {
+    /* Process Locked */
+    __HAL_LOCK(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_BUSY;
+
+    /* Disable the selected I2C peripheral */
+    __HAL_I2C_DISABLE(hi2c);
+
+    /* Reset I2Cx ANOFF bit */
+    hi2c->Instance->CR1 &= ~(I2C_CR1_ANFOFF);
+
+    /* Set analog filter bit*/
+    hi2c->Instance->CR1 |= AnalogFilter;
+
+    __HAL_I2C_ENABLE(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hi2c);
+
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+
+/**
+  * @brief  Configure I2C Digital noise filter.
+  * @param  hi2c Pointer to a I2C_HandleTypeDef structure that contains
+  *                the configuration information for the specified I2Cx peripheral.
+  * @param  DigitalFilter Coefficient of digital noise filter between Min_Data=0x00 and Max_Data=0x0F.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_I2CEx_ConfigDigitalFilter(I2C_HandleTypeDef *hi2c, uint32_t DigitalFilter)
+{
+  uint32_t tmpreg;
+
+  /* Check the parameters */
+  assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance));
+  assert_param(IS_I2C_DIGITAL_FILTER(DigitalFilter));
+
+  if (hi2c->State == HAL_I2C_STATE_READY)
+  {
+    /* Process Locked */
+    __HAL_LOCK(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_BUSY;
+
+    /* Disable the selected I2C peripheral */
+    __HAL_I2C_DISABLE(hi2c);
+
+    /* Get the old register value */
+    tmpreg = hi2c->Instance->CR1;
+
+    /* Reset I2Cx DNF bits [11:8] */
+    tmpreg &= ~(I2C_CR1_DNF);
+
+    /* Set I2Cx DNF coefficient */
+    tmpreg |= DigitalFilter << 8U;
+
+    /* Store the new register value */
+    hi2c->Instance->CR1 = tmpreg;
+
+    __HAL_I2C_ENABLE(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hi2c);
+
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+/**
+  * @}
+  */
+
+/** @defgroup I2CEx_Exported_Functions_Group2 WakeUp Mode Functions
+  * @brief    WakeUp Mode Functions
+  *
+@verbatim
+ ===============================================================================
+                      ##### WakeUp Mode Functions #####
+ ===============================================================================
+    [..] This section provides functions allowing to:
+      (+) Configure Wake Up Feature
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Enable I2C wakeup from Stop mode(s).
+  * @param  hi2c Pointer to a I2C_HandleTypeDef structure that contains
+  *                the configuration information for the specified I2Cx peripheral.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_I2CEx_EnableWakeUp(I2C_HandleTypeDef *hi2c)
+{
+  /* Check the parameters */
+  assert_param(IS_I2C_WAKEUP_FROMSTOP_INSTANCE(hi2c->Instance));
+
+  if (hi2c->State == HAL_I2C_STATE_READY)
+  {
+    /* Process Locked */
+    __HAL_LOCK(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_BUSY;
+
+    /* Disable the selected I2C peripheral */
+    __HAL_I2C_DISABLE(hi2c);
+
+    /* Enable wakeup from stop mode */
+    hi2c->Instance->CR1 |= I2C_CR1_WUPEN;
+
+    __HAL_I2C_ENABLE(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hi2c);
+
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+
+/**
+  * @brief  Disable I2C wakeup from Stop mode(s).
+  * @param  hi2c Pointer to a I2C_HandleTypeDef structure that contains
+  *                the configuration information for the specified I2Cx peripheral.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_I2CEx_DisableWakeUp(I2C_HandleTypeDef *hi2c)
+{
+  /* Check the parameters */
+  assert_param(IS_I2C_WAKEUP_FROMSTOP_INSTANCE(hi2c->Instance));
+
+  if (hi2c->State == HAL_I2C_STATE_READY)
+  {
+    /* Process Locked */
+    __HAL_LOCK(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_BUSY;
+
+    /* Disable the selected I2C peripheral */
+    __HAL_I2C_DISABLE(hi2c);
+
+    /* Enable wakeup from stop mode */
+    hi2c->Instance->CR1 &= ~(I2C_CR1_WUPEN);
+
+    __HAL_I2C_ENABLE(hi2c);
+
+    hi2c->State = HAL_I2C_STATE_READY;
+
+    /* Process Unlocked */
+    __HAL_UNLOCK(hi2c);
+
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+/**
+  * @}
+  */
+#if  (defined(SYSCFG_CFGR2_I2C_PB6_FMP) || defined(SYSCFG_CFGR2_I2C_PB7_FMP)) || (defined(SYSCFG_CFGR2_I2C_PB8_FMP) || defined(SYSCFG_CFGR2_I2C_PB9_FMP)) || (defined(SYSCFG_CFGR2_I2C1_FMP)) || defined(SYSCFG_CFGR2_I2C2_FMP) || defined(SYSCFG_CFGR2_I2C3_FMP)
+
+/** @defgroup I2CEx_Exported_Functions_Group3 Fast Mode Plus Functions
+  * @brief    Fast Mode Plus Functions
+  *
+@verbatim
+ ===============================================================================
+                      ##### Fast Mode Plus Functions #####
+ ===============================================================================
+    [..] This section provides functions allowing to:
+      (+) Configure Fast Mode Plus
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief Enable the I2C fast mode plus driving capability.
+  * @param ConfigFastModePlus Selects the pin.
+  *   This parameter can be one of the @ref I2CEx_FastModePlus values
+  * @note  For I2C1, fast mode plus driving capability can be enabled on all selected
+  *        I2C1 pins using I2C_FASTMODEPLUS_I2C1 parameter or independently
+  *        on each one of the following pins PB6, PB7, PB8 and PB9.
+  * @note  For remaining I2C1 pins (PA14, PA15...) fast mode plus driving capability
+  *        can be enabled only by using I2C_FASTMODEPLUS_I2C1 parameter.
+  * @note  For all I2C2 pins fast mode plus driving capability can be enabled
+  *        only by using I2C_FASTMODEPLUS_I2C2 parameter.
+  * @note  For all I2C3 pins fast mode plus driving capability can be enabled
+  *        only by using I2C_FASTMODEPLUS_I2C3 parameter.
+  * @retval None
+  */
+void HAL_I2CEx_EnableFastModePlus(uint32_t ConfigFastModePlus)
+{
+  /* Check the parameter */
+  assert_param(IS_I2C_FASTMODEPLUS(ConfigFastModePlus));
+
+  /* Enable SYSCFG clock */
+  __HAL_RCC_SYSCFG_CLK_ENABLE();
+
+  /* Enable fast mode plus driving capability for selected pin */
+  SET_BIT(SYSCFG->CFGR2, (uint32_t)ConfigFastModePlus);
+}
+
+/**
+  * @brief Disable the I2C fast mode plus driving capability.
+  * @param ConfigFastModePlus Selects the pin.
+  *   This parameter can be one of the @ref I2CEx_FastModePlus values
+  * @note  For I2C1, fast mode plus driving capability can be disabled on all selected
+  *        I2C1 pins using I2C_FASTMODEPLUS_I2C1 parameter or independently
+  *        on each one of the following pins PB6, PB7, PB8 and PB9.
+  * @note  For remaining I2C1 pins (PA14, PA15...) fast mode plus driving capability
+  *        can be disabled only by using I2C_FASTMODEPLUS_I2C1 parameter.
+  * @note  For all I2C2 pins fast mode plus driving capability can be disabled
+  *        only by using I2C_FASTMODEPLUS_I2C2 parameter.
+  * @note  For all I2C3 pins fast mode plus driving capability can be disabled
+  *        only by using I2C_FASTMODEPLUS_I2C3 parameter.
+  * @retval None
+  */
+void HAL_I2CEx_DisableFastModePlus(uint32_t ConfigFastModePlus)
+{
+  /* Check the parameter */
+  assert_param(IS_I2C_FASTMODEPLUS(ConfigFastModePlus));
+
+  /* Enable SYSCFG clock */
+  __HAL_RCC_SYSCFG_CLK_ENABLE();
+
+  /* Disable fast mode plus driving capability for selected pin */
+  CLEAR_BIT(SYSCFG->CFGR2, (uint32_t)ConfigFastModePlus);
+}
+/**
+  * @}
+  */
+#endif /* Fast Mode Plus Availability */
+/**
+  * @}
+  */
+
+#endif /* HAL_I2C_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_pwr.c

@@ -0,0 +1,733 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_pwr.c
+  * @author  MCD Application Team
+  * @brief   PWR HAL module driver.
+  *
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the Power Controller (PWR) peripheral:
+  *           + Initialization/de-initialization functions
+  *           + Peripheral Control functions 
+  *
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+#ifdef HAL_PWR_MODULE_ENABLED
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup PWR
+  * @{
+  */
+
+/** @addtogroup PWR_Private
+  * @{
+  */
+  
+#if defined(PWR_PVD_SUPPORT)
+/** @defgroup PWR_PVD_Mode_Mask PWR PVD Mode Mask
+  * @{
+  */ 
+#define PVD_MODE_IT               (0x00010000U)
+#define PVD_MODE_EVT              (0x00020000U)
+#define PVD_RISING_EDGE           (0x00000001U)
+#define PVD_FALLING_EDGE          (0x00000002U)
+/**
+  * @}
+  */
+#endif
+
+/**
+  * @}
+  */  
+  
+
+/** @addtogroup PWR_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup PWR_Exported_Functions_Group1
+  * @brief      Initialization and de-initialization functions
+  *
+@verbatim
+ ===============================================================================
+              ##### Initialization and de-initialization functions #####
+ ===============================================================================
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief Deinitializes the HAL PWR peripheral registers to their default reset values.
+  * @retval None
+  */
+void HAL_PWR_DeInit(void)
+{
+  __HAL_RCC_PWR_FORCE_RESET();
+  __HAL_RCC_PWR_RELEASE_RESET();
+}
+
+/**
+  * @}
+  */
+
+/** @addtogroup PWR_Exported_Functions_Group2
+  * @brief      Low Power modes configuration functions
+  *
+@verbatim
+
+ ===============================================================================
+                 ##### Peripheral Control functions #####
+ ===============================================================================
+     
+    *** Backup domain ***
+    =========================
+    [..]
+      After reset, the backup domain (RTC registers, RTC backup data
+      registers) is protected against possible unwanted
+      write accesses.
+      To enable access to the RTC Domain and RTC registers, proceed as follows:
+        (+) Enable the Power Controller (PWR) APB1 interface clock using the
+            __HAL_RCC_PWR_CLK_ENABLE() macro.
+        (+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function.
+
+    *** PVD configuration ***
+    =========================
+    [..]
+      (+) The PVD is used to monitor the VDD power supply by comparing it to a
+          threshold selected by the PVD Level (PLS[2:0] bits in the PWR_CR).
+      (+) The PVD can use an external input analog voltage (PVD_IN) which is compared 
+      internally to VREFINT. The PVD_IN (PB7) has to be configured in Analog mode 
+      when PWR_PVDLevel_7 is selected (PLS[2:0] = 111).
+
+      (+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower
+          than the PVD threshold. This event is internally connected to the EXTI
+          line16 and can generate an interrupt if enabled. This is done through
+          __HAL_PWR_PVD_EXTI_ENABLE_IT() macro.
+      (+) The PVD is stopped in Standby mode.
+      (+) The PVD feature is not supported on L0 Value line.
+
+    *** WakeUp pin configuration ***
+    ================================
+    [..]
+      (+) WakeUp pin is used to wake up the system from Standby mode. This pin is
+          forced in input pull-down configuration and is active on rising edges.
+      (+) There are two WakeUp pins:
+          WakeUp Pin 1 on PA.00.
+          WakeUp Pin 2 on PC.13.
+          WakeUp Pin 3 on PE.06 .
+          
+
+    [..]
+    *** Main and Backup Regulators configuration ***
+    ================================================
+
+      (+) The main internal regulator can be configured to have a tradeoff between
+          performance and power consumption when the device does not operate at
+          the maximum frequency. This is done through __HAL_PWR_VOLTAGESCALING_CONFIG()
+          macro which configures the two VOS bits in PWR_CR register:
+        (++) PWR_REGULATOR_VOLTAGE_SCALE1 (VOS bits = 01), the regulator voltage output Scale 1 mode selected and
+             the System frequency can go up to 32 MHz.
+        (++) PWR_REGULATOR_VOLTAGE_SCALE2 (VOS bits = 10), the regulator voltage output Scale 2 mode selected and
+             the System frequency can go up to 16 MHz.
+        (++) PWR_REGULATOR_VOLTAGE_SCALE3 (VOS bits = 11), the regulator voltage output Scale 3 mode selected and
+             the System frequency can go up to 4.2 MHz.
+              
+        Refer to the datasheets for more details.
+
+    *** Low Power modes configuration ***
+    =====================================
+     [..]
+      The device features 5 low-power modes:
+      (+) Low power run mode: regulator in low power mode, limited clock frequency, 
+        limited number of peripherals running.
+      (+) Sleep mode: Cortex-M0+ core stopped, peripherals kept running.
+      (+) Low power sleep mode: Cortex-M0+ core stopped, limited clock frequency, 
+         limited number of peripherals running, regulator in low power mode.
+      (+) Stop mode: All clocks are stopped, regulator running, regulator in low power mode.
+      (+) Standby mode: VCORE domain powered off
+  
+   *** Low power run mode ***
+   =========================
+    [..]
+       To further reduce the consumption when the system is in Run mode, the regulator can be
+        configured in low power mode. In this mode, the system frequency should not exceed
+        MSI frequency range1.
+        In Low power run mode, all I/O pins keep the same state as in Run mode.
+  
+      (+) Entry:
+        (++) VCORE in range2
+        (++) Decrease the system frequency not to exceed the frequency of MSI frequency range1.
+        (++) The regulator is forced in low power mode using the HAL_PWREx_EnableLowPowerRunMode()
+             function.
+      (+) Exit:
+        (++) The regulator is forced in Main regulator mode using the HAL_PWREx_DisableLowPowerRunMode()
+              function.
+        (++) Increase the system frequency if needed.
+  
+   *** Sleep mode ***
+   ==================
+    [..]
+      (+) Entry:
+          The Sleep mode is entered by using the HAL_PWR_EnterSLEEPMode(PWR_MAINREGULATOR_ON, PWR_SLEEPENTRY_WFx)
+              functions with
+          (++) PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
+          (++) PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
+     
+      (+) Exit:
+        (++) Any peripheral interrupt acknowledged by the nested vectored interrupt
+              controller (NVIC) can wake up the device from Sleep mode. If the WFE instruction was used to enter sleep mode,
+              the MCU exits Sleep mode as soon as an event occurs. 
+
+   *** Low power sleep mode ***
+   ============================
+    [..]
+      (+) Entry:
+          The Low power sleep mode is entered by using the HAL_PWR_EnterSLEEPMode(PWR_LOWPOWERREGULATOR_ON, PWR_SLEEPENTRY_WFx)
+              functions with
+          (++) PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
+          (++) PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
+       (+) The Flash memory can be switched off by using the control bits (SLEEP_PD in the FLASH_ACR register. 
+             This reduces power consumption but increases the wake-up time.
+         
+      (+) Exit:
+        (++) If the WFI instruction was used to enter Low power sleep mode, any peripheral interrupt
+              acknowledged by the nested vectored interrupt controller (NVIC) can wake up the device
+              from Low power sleep mode. If the WFE instruction was used to enter Low power sleep mode,
+              the MCU exits Sleep mode as soon as an event occurs. 
+                
+   *** Stop mode ***
+   =================
+    [..]
+      The Stop mode is based on the Cortex-M0+ deepsleep mode combined with peripheral
+      clock gating. The voltage regulator can be configured either in normal or low-power mode.
+      In Stop mode, all clocks in the VCORE domain are stopped, the PLL, the MSI, the HSI and
+      the HSE RC oscillators are disabled. Internal SRAM and register contents are preserved.
+      To get the lowest consumption in Stop mode, the internal Flash memory also enters low
+      power mode. When the Flash memory is in power-down mode, an additional startup delay is
+      incurred when waking up from Stop mode.
+      To minimize the consumption In Stop mode, VREFINT, the BOR, PVD, and temperature
+      sensor can be switched off before entering Stop mode. They can be switched on again by
+      software after exiting Stop mode using the ULP bit in the PWR_CR register.
+      In Stop mode, all I/O pins keep the same state as in Run mode.
+
+      (+) Entry:
+           The Stop mode is entered using the HAL_PWR_EnterSTOPMode
+             function with:
+          (++) Main regulator ON.
+          (++) Low Power regulator ON.
+          (++) PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
+          (++) PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
+      (+) Exit:
+        (++) By issuing an interrupt or a wakeup event, the MSI or HSI16 RC
+             oscillator is selected as system clock depending the bit STOPWUCK in the RCC_CFGR
+             register
+
+   *** Standby mode ***
+   ====================
+     [..]
+      The Standby mode allows to achieve the lowest power consumption. It is based on the
+      Cortex-M0+ deepsleep mode, with the voltage regulator disabled. The VCORE domain is
+      consequently powered off. The PLL, the MSI, the HSI oscillator and the HSE oscillator are
+      also switched off. SRAM and register contents are lost except for the RTC registers, RTC
+      backup registers and Standby circuitry.
+      
+      To minimize the consumption In Standby mode, VREFINT, the BOR, PVD, and temperature
+       sensor can be switched off before entering the Standby mode. They can be switched 
+       on again by software after exiting the Standby mode.
+       function.
+      
+      (+) Entry:
+        (++) The Standby mode is entered using the HAL_PWR_EnterSTANDBYMode() function.
+      (+) Exit:
+        (++) WKUP pin rising edge, RTC alarm (Alarm A and Alarm B), RTC wakeup,
+             tamper event, time-stamp event, external reset in NRST pin, IWDG reset.
+
+   *** Auto-wakeup (AWU) from low-power mode ***
+   =============================================
+    [..]
+      The MCU can be woken up from low-power mode by an RTC Alarm event, an RTC 
+      Wakeup event, a tamper event, a time-stamp event, or a comparator event, 
+      without depending on an external interrupt (Auto-wakeup mode).
+
+    (+) RTC auto-wakeup (AWU) from the Stop mode
+        (++) To wake up from the Stop mode with an RTC alarm event, it is necessary to:
+             (+++) Configure the EXTI Line 17 to be sensitive to rising edges (Interrupt 
+                   or Event modes) using the EXTI_Init() function.
+             (+++) Enable the RTC Alarm Interrupt using the RTC_ITConfig() function
+             (+++) Configure the RTC to generate the RTC alarm using the RTC_SetAlarm() 
+                   and RTC_AlarmCmd() functions.
+        (++) To wake up from the Stop mode with an RTC Tamper or time stamp event, it 
+             is necessary to:
+             (+++) Configure the EXTI Line 19 to be sensitive to rising edges (Interrupt 
+                   or Event modes) using the EXTI_Init() function.
+             (+++) Enable the RTC Tamper or time stamp Interrupt using the RTC_ITConfig() 
+                   function.
+             (+++) Configure the RTC to detect the tamper or time stamp event using the
+                   RTC_TimeStampConfig(), RTC_TamperTriggerConfig() and RTC_TamperCmd()
+                   functions.
+        (++) To wake up from the Stop mode with an RTC WakeUp event, it is necessary to:
+             (+++) Configure the EXTI Line 20 to be sensitive to rising edges (Interrupt 
+                   or Event modes) using the EXTI_Init() function.
+             (+++) Enable the RTC WakeUp Interrupt using the RTC_ITConfig() function.
+             (+++) Configure the RTC to generate the RTC WakeUp event using the RTC_WakeUpClockConfig(), 
+                   RTC_SetWakeUpCounter() and RTC_WakeUpCmd() functions.
+
+    (+) RTC auto-wakeup (AWU) from the Standby mode
+        (++) To wake up from the Standby mode with an RTC alarm event, it is necessary to:
+             (+++) Enable the RTC Alarm Interrupt using the RTC_ITConfig() function.
+             (+++) Configure the RTC to generate the RTC alarm using the RTC_SetAlarm() 
+                   and RTC_AlarmCmd() functions.
+        (++) To wake up from the Standby mode with an RTC Tamper or time stamp event, it 
+             is necessary to:
+             (+++) Enable the RTC Tamper or time stamp Interrupt using the RTC_ITConfig() 
+                   function.
+             (+++) Configure the RTC to detect the tamper or time stamp event using the
+                   RTC_TimeStampConfig(), RTC_TamperTriggerConfig() and RTC_TamperCmd()
+                   functions.
+        (++) To wake up from the Standby mode with an RTC WakeUp event, it is necessary to:
+             (+++) Enable the RTC WakeUp Interrupt using the RTC_ITConfig() function
+             (+++) Configure the RTC to generate the RTC WakeUp event using the RTC_WakeUpClockConfig(), 
+                   RTC_SetWakeUpCounter() and RTC_WakeUpCmd() functions.
+
+    (+) Comparator auto-wakeup (AWU) from the Stop mode
+        (++) To wake up from the Stop mode with an comparator 1 or comparator 2 wakeup
+             event, it is necessary to:
+             (+++) Configure the EXTI Line 21 for comparator 1 or EXTI Line 22 for comparator 2 
+                   to be sensitive to to the selected edges (falling, rising or falling 
+                   and rising) (Interrupt or Event modes) using the EXTI_Init() function.
+             (+++) Configure the comparator to generate the event.      
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief Enables access to the backup domain (RTC registers, RTC
+  *         backup data registers ).
+  * @note   If the HSE divided by 2, 4, 8 or 16 is used as the RTC clock, the
+  *         Backup Domain Access should be kept enabled.
+  * @retval None
+  */
+void HAL_PWR_EnableBkUpAccess(void)
+{
+  /* Enable access to RTC and backup registers */
+  SET_BIT(PWR->CR, PWR_CR_DBP);
+}
+
+/**
+  * @brief  Disables access to the backup domain 
+  * @note   Applies to RTC registers, RTC backup data registers.
+  * @note   If the HSE divided by 2, 4, 8 or 16 is used as the RTC clock, the
+  *         Backup Domain Access should be kept enabled.
+  * @retval None
+  */
+void HAL_PWR_DisableBkUpAccess(void)
+{
+  /* Disable access to RTC and backup registers */
+  CLEAR_BIT(PWR->CR, PWR_CR_DBP);
+}
+
+#if defined(PWR_PVD_SUPPORT)
+/**
+  * @brief  Configures the voltage threshold detected by the Power Voltage Detector(PVD).
+  * @param  sConfigPVD pointer to an PWR_PVDTypeDef structure that contains the configuration
+  *         information for the PVD.
+  * @note   Refer to the electrical characteristics of your device datasheet for
+  *         more details about the voltage threshold corresponding to each
+  *         detection level.
+  * @retval None
+  */
+void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD)
+{
+  /* Check the parameters */
+  assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel));
+  assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode));
+
+  /* Set PLS[7:5] bits according to PVDLevel value */
+  MODIFY_REG(PWR->CR, PWR_CR_PLS, sConfigPVD->PVDLevel);
+  
+  /* Clear any previous config. Keep it clear if no event or IT mode is selected */
+  __HAL_PWR_PVD_EXTI_DISABLE_EVENT();
+  __HAL_PWR_PVD_EXTI_DISABLE_IT();
+  __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); 
+  __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();
+
+  /* Configure interrupt mode */
+  if((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT)
+  {
+    __HAL_PWR_PVD_EXTI_ENABLE_IT();
+  }
+  
+  /* Configure event mode */
+  if((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT)
+  {
+    __HAL_PWR_PVD_EXTI_ENABLE_EVENT();
+  }
+  
+  /* Configure the edge */
+  if((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE)
+  {
+    __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();
+  }
+  
+  if((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE)
+  {
+    __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();
+  }
+}
+
+/**
+  * @brief Enables the Power Voltage Detector(PVD).
+  * @retval None
+  */
+void HAL_PWR_EnablePVD(void)
+{
+  /* Enable the power voltage detector */
+  SET_BIT(PWR->CR, PWR_CR_PVDE);
+}
+
+/**
+  * @brief Disables the Power Voltage Detector(PVD).
+  * @retval None
+  */
+void HAL_PWR_DisablePVD(void)
+{
+  /* Disable the power voltage detector */
+  CLEAR_BIT(PWR->CR, PWR_CR_PVDE);
+}
+#endif /* PWR_PVD_SUPPORT */
+
+/**
+  * @brief Enables the WakeUp PINx functionality.
+  * @param WakeUpPinx: Specifies the Power Wake-Up pin to enable.
+  *         This parameter can be one of the following values:
+  *           @arg PWR_WAKEUP_PIN1
+  *           @arg PWR_WAKEUP_PIN2
+  *           @arg PWR_WAKEUP_PIN3 for stm32l07xxx and stm32l08xxx devices only.
+  * @retval None
+  */
+void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx)
+{
+  /* Check the parameter */
+  assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx));
+  /* Enable the EWUPx pin */
+  SET_BIT(PWR->CSR, WakeUpPinx);
+}
+
+/**
+  * @brief Disables the WakeUp PINx functionality.
+  * @param WakeUpPinx: Specifies the Power Wake-Up pin to disable.
+  *         This parameter can be one of the following values:
+  *           @arg PWR_WAKEUP_PIN1
+  *           @arg PWR_WAKEUP_PIN2  
+  *           @arg PWR_WAKEUP_PIN3  for stm32l07xxx and stm32l08xxx devices only.
+  * @retval None
+  */
+void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx)
+{
+  /* Check the parameter */
+  assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx));
+  /* Disable the EWUPx pin */
+  CLEAR_BIT(PWR->CSR, WakeUpPinx);
+}
+
+/**
+  * @brief Enters Sleep mode.
+  * @note In Sleep mode, all I/O pins keep the same state as in Run mode.
+  * @param Regulator: Specifies the regulator state in SLEEP mode.
+  *          This parameter can be one of the following values:
+  *            @arg PWR_MAINREGULATOR_ON: SLEEP mode with regulator ON
+  *            @arg PWR_LOWPOWERREGULATOR_ON: SLEEP mode with low power regulator ON
+  * @param SLEEPEntry: Specifies if SLEEP mode is entered with WFI or WFE instruction.
+  *           When WFI entry is used, tick interrupt have to be disabled if not desired as 
+  *           the interrupt wake up source.
+  *           This parameter can be one of the following values:
+  *            @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
+  *            @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
+  * @retval None
+  */
+void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry)
+{
+   uint32_t tmpreg = 0U;
+   uint32_t ulpbit, vrefinbit;
+
+  /* Check the parameters */
+  assert_param(IS_PWR_REGULATOR(Regulator));
+  assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry));
+
+  /* It is forbidden to configure both EN_VREFINT=1 and ULP=1 if the device is
+     in Stop mode or in Sleep/Low-power sleep mode */
+  ulpbit = READ_BIT(PWR->CR, PWR_CR_ULP);
+  vrefinbit = READ_BIT(SYSCFG->CFGR3, SYSCFG_CFGR3_EN_VREFINT);
+  if((ulpbit != 0) && (vrefinbit != 0))
+  {
+    CLEAR_BIT(PWR->CR, PWR_CR_ULP);
+  }
+
+  /* Select the regulator state in Sleep mode ---------------------------------*/
+  tmpreg = PWR->CR;
+
+  /* Clear PDDS and LPDS bits */
+  CLEAR_BIT(tmpreg, (PWR_CR_PDDS | PWR_CR_LPSDSR));
+
+ /* Set LPSDSR bit according to PWR_Regulator value */
+  SET_BIT(tmpreg, Regulator);
+
+  /* Store the new value */
+  PWR->CR = tmpreg;
+  
+  /* Clear SLEEPDEEP bit of Cortex System Control Register */
+  CLEAR_BIT(SCB->SCR, SCB_SCR_SLEEPDEEP_Msk);
+
+  /* Select SLEEP mode entry -------------------------------------------------*/
+  if(SLEEPEntry == PWR_SLEEPENTRY_WFI)
+  {
+    /* Request Wait For Interrupt */
+    __WFI();
+  }
+  else
+  {
+    /* Request Wait For Event */
+    __SEV();
+    __WFE();
+    __WFE();
+  }
+
+  if((ulpbit != 0) && (vrefinbit != 0))
+  {
+    SET_BIT(PWR->CR, PWR_CR_ULP);
+  }
+
+  /* Additional NOP to ensure all pending instructions are flushed before entering low power mode */
+  __NOP();
+
+}
+
+/**
+  * @brief Enters Stop mode. 
+  * @note In Stop mode, all I/O pins keep the same state as in Run mode.
+  * @note When exiting Stop mode by issuing an interrupt or a wakeup event,
+  *        MSI or HSI16 RCoscillator is selected as system clock depending 
+  *        the bit STOPWUCK in the RCC_CFGR register.
+  * @note When the voltage regulator operates in low power mode, an additional
+  *         startup delay is incurred when waking up from Stop mode. 
+  *         By keeping the internal regulator ON during Stop mode, the consumption
+  *         is higher although the startup time is reduced.
+  * @note Before entering in this function, it is important to ensure that the WUF
+  *       wakeup flag is cleared. To perform this action, it is possible to call the
+  *       following macro : __HAL_PWR_CLEAR_FLAG(PWR_FLAG_WU)
+  *
+  * @param Regulator: Specifies the regulator state in Stop mode.
+  *          This parameter can be one of the following values:
+  *            @arg PWR_MAINREGULATOR_ON: Stop mode with regulator ON
+  *            @arg PWR_LOWPOWERREGULATOR_ON: Stop mode with low power regulator ON
+  * @param STOPEntry: Specifies if Stop mode in entered with WFI or WFE instruction.
+  *          This parameter can be one of the following values:
+  *            @arg PWR_STOPENTRY_WFI: Enter Stop mode with WFI instruction
+  *            @arg PWR_STOPENTRY_WFE: Enter Stop mode with WFE instruction   
+  * @retval None
+  */
+void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry)
+{
+  uint32_t tmpreg = 0U;
+  uint32_t ulpbit, vrefinbit;
+
+  /* Check the parameters */
+  assert_param(IS_PWR_REGULATOR(Regulator));
+  assert_param(IS_PWR_STOP_ENTRY(STOPEntry));
+
+  /* It is forbidden to configure both EN_VREFINT=1 and ULP=1 if the device is
+     in Stop mode or in Sleep/Low-power sleep mode */
+  ulpbit = READ_BIT(PWR->CR, PWR_CR_ULP);
+  vrefinbit = READ_BIT(SYSCFG->CFGR3, SYSCFG_CFGR3_EN_VREFINT);
+  if((ulpbit != 0) && (vrefinbit != 0))
+  {
+    CLEAR_BIT(PWR->CR, PWR_CR_ULP);
+  }
+
+  /* Select the regulator state in Stop mode ---------------------------------*/
+  tmpreg = PWR->CR;
+  
+  /* Clear PDDS and LPDS bits */
+  CLEAR_BIT(tmpreg, (PWR_CR_PDDS | PWR_CR_LPSDSR));
+
+ /* Set LPSDSR bit according to PWR_Regulator value */
+  SET_BIT(tmpreg, Regulator);
+
+  /* Store the new value */
+  PWR->CR = tmpreg;
+
+  /* Set SLEEPDEEP bit of Cortex System Control Register */
+  SET_BIT(SCB->SCR, SCB_SCR_SLEEPDEEP_Msk);
+
+  /* Select Stop mode entry --------------------------------------------------*/
+  if(STOPEntry == PWR_STOPENTRY_WFI)
+  {
+    /* Request Wait For Interrupt */
+    __WFI();
+  }
+  else
+  {
+    /* Request Wait For Event */
+    __SEV();
+    __WFE();
+    __WFE();
+  }
+ 
+  /* Reset SLEEPDEEP bit of Cortex System Control Register */
+  CLEAR_BIT(SCB->SCR, SCB_SCR_SLEEPDEEP_Msk);
+
+  if((ulpbit != 0) && (vrefinbit != 0))
+  {
+    SET_BIT(PWR->CR, PWR_CR_ULP);
+  }
+}
+
+/**
+  * @brief Enters Standby mode.
+  * @note In Standby mode, all I/O pins are high impedance except for:
+  *          - Reset pad (still available) 
+  *          - RTC_AF1 pin (PC13) if configured for tamper, time-stamp, RTC
+  *            Alarm out, or RTC clock calibration out.
+  *          - RTC_AF2 pin (PC13) if configured for tamper.
+  *          - WKUP pin 1 (PA00) if enabled.
+  *          - WKUP pin 2 (PC13) if enabled.
+  *          - WKUP pin 3 (PE06) if enabled, for stm32l07xxx and stm32l08xxx devices only.
+  *          - WKUP pin 3 (PA02) if enabled, for stm32l031xx devices only.
+  * @retval None
+  */
+void HAL_PWR_EnterSTANDBYMode(void)
+{
+  /* Select Standby mode */
+  SET_BIT(PWR->CR, PWR_CR_PDDS);
+
+  /* Set SLEEPDEEP bit of Cortex System Control Register */
+  SET_BIT(SCB->SCR, SCB_SCR_SLEEPDEEP_Msk);
+
+  /* This option is used to ensure that store operations are completed */
+#if defined ( __CC_ARM)
+  __force_stores();
+#endif
+  /* Request Wait For Interrupt */
+  __WFI();
+}
+
+/**
+  * @brief Indicates Sleep-On-Exit when returning from Handler mode to Thread mode. 
+  * @note Set SLEEPONEXIT bit of SCR register. When this bit is set, the processor 
+  *       re-enters SLEEP mode when an interruption handling is over.
+  *       Setting this bit is useful when the processor is expected to run only on
+  *       interruptions handling.         
+  * @retval None
+  */
+void HAL_PWR_EnableSleepOnExit(void)
+{
+  /* Set SLEEPONEXIT bit of Cortex System Control Register */
+  SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk));
+}
+
+
+/**
+  * @brief Disables Sleep-On-Exit feature when returning from Handler mode to Thread mode. 
+  * @note Clears SLEEPONEXIT bit of SCR register. When this bit is set, the processor 
+  *       re-enters SLEEP mode when an interruption handling is over.          
+  * @retval None
+  */
+void HAL_PWR_DisableSleepOnExit(void)
+{
+  /* Clear SLEEPONEXIT bit of Cortex System Control Register */
+  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk));
+}
+
+
+/**
+  * @brief Enables CORTEX M0+ SEVONPEND bit. 
+  * @note Sets SEVONPEND bit of SCR register. When this bit is set, this causes 
+  *       WFE to wake up when an interrupt moves from inactive to pended.
+  * @retval None
+  */
+void HAL_PWR_EnableSEVOnPend(void)
+{
+  /* Set SEVONPEND bit of Cortex System Control Register */
+  SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk));
+}
+
+
+/**
+  * @brief Disables CORTEX M0+ SEVONPEND bit. 
+  * @note Clears SEVONPEND bit of SCR register. When this bit is set, this causes 
+  *       WFE to wake up when an interrupt moves from inactive to pended.         
+  * @retval None
+  */
+void HAL_PWR_DisableSEVOnPend(void)
+{
+  /* Clear SEVONPEND bit of Cortex System Control Register */
+  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk));
+}
+
+#if defined(PWR_PVD_SUPPORT)
+/**
+  * @brief This function handles the PWR PVD interrupt request.
+  * @note This API should be called under the PVD_IRQHandler().
+  * @retval None
+  */
+void HAL_PWR_PVD_IRQHandler(void)
+{
+  /* Check PWR exti flag */
+  if(__HAL_PWR_PVD_EXTI_GET_FLAG() != RESET)
+  {
+    /* PWR PVD interrupt user callback */
+    HAL_PWR_PVDCallback();
+
+    /* Clear PWR Exti pending bit */
+    __HAL_PWR_PVD_EXTI_CLEAR_FLAG();
+  }
+}
+
+/**
+  * @brief  PWR PVD interrupt callback
+  * @retval None
+  */
+__weak void HAL_PWR_PVDCallback(void)
+{
+  /* NOTE : This function Should not be modified, when the callback is needed,
+            the HAL_PWR_PVDCallback could be implemented in the user file
+   */ 
+}
+#endif /* PWR_PVD_SUPPORT */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_PWR_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_pwr_ex.c

@@ -0,0 +1,184 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_pwr_ex.c
+  * @author  MCD Application Team
+  * @brief   Extended PWR HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the Power Controller (PWR) peripheral:
+  *           + Extended Initialization and de-initialization functions
+  *           + Extended Peripheral Control functions
+  *         
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright(c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+#ifdef HAL_PWR_MODULE_ENABLED
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup PWREx 
+  * @{
+  */
+
+/** @addtogroup PWREx_Private
+  * @{
+  */
+
+/** @defgroup PWR_Extended_TimeOut_Value PWREx Flag Setting Time Out Value
+  * @{
+  */ 
+#define PWR_FLAG_SETTING_DELAY_US 50U
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+
+/** @addtogroup PWREx_Exported_Functions
+  * @brief      Low Power modes configuration functions 
+  *
+@verbatim
+
+ ===============================================================================
+                 ##### Peripheral extended features functions #####
+ ===============================================================================
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief Return Voltage Scaling Range.   
+  * @retval VOS bit field (PWR_REGULATOR_VOLTAGE_SCALE1, PWR_REGULATOR_VOLTAGE_SCALE2 or PWR_REGULATOR_VOLTAGE_SCALE3)
+  */  
+uint32_t HAL_PWREx_GetVoltageRange(void)
+{
+  return  (PWR->CR & PWR_CR_VOS);
+}
+
+
+/**
+  * @brief  Enables the Fast WakeUp from Ultra Low Power mode.
+  * @note This bit works in conjunction with ULP bit. 
+  *        Means, when ULP = 1 and FWU = 1 :VREFINT startup time is ignored when 
+  *        exiting from low power mode.
+  * @retval None
+  */
+void HAL_PWREx_EnableFastWakeUp(void)
+{
+  /* Enable the fast wake up */
+  SET_BIT(PWR->CR, PWR_CR_FWU);
+}
+
+/**
+  * @brief  Disables the Fast WakeUp from Ultra Low Power mode.
+  * @retval None
+  */
+void HAL_PWREx_DisableFastWakeUp(void)
+{
+  /* Disable the fast wake up */
+  CLEAR_BIT(PWR->CR, PWR_CR_FWU);
+}
+
+/**
+  * @brief  Enables the Ultra Low Power mode
+  * @retval None
+  */
+void HAL_PWREx_EnableUltraLowPower(void)
+{
+  /* Enable the Ultra Low Power mode */
+  SET_BIT(PWR->CR, PWR_CR_ULP);
+}
+
+/**
+  * @brief  Disables the Ultra Low Power mode
+  * @retval None
+  */
+void HAL_PWREx_DisableUltraLowPower(void)
+{
+  /* Disable the Ultra Low Power mode */
+  CLEAR_BIT(PWR->CR, PWR_CR_ULP);
+}
+
+/**
+  * @brief  Enable the Low Power Run mode.
+  * @note   Low power run mode can only be entered when VCORE is in range 2.
+  *         In addition, the dynamic voltage scaling must not be used when Low
+  *         power run mode is selected. Only Stop and Sleep modes with regulator
+  *         configured in Low power mode is allowed when Low power run mode is 
+  *         selected.
+  * @note   The frequency of the system clock must be decreased to not exceed the
+  *         frequency of RCC_MSIRANGE_1.
+  * @note   In Low power run mode, all I/O pins keep the same state as in Run mode.
+  * @retval None
+  */
+void HAL_PWREx_EnableLowPowerRunMode(void)
+{
+  /* Enters the Low Power Run mode */
+  SET_BIT(PWR->CR, PWR_CR_LPSDSR);
+  SET_BIT(PWR->CR, PWR_CR_LPRUN);
+}
+
+/**
+  * @brief  Disable the Low Power Run mode.
+  * @note  Before HAL_PWREx_DisableLowPowerRunMode() completion, the function checks that 
+  *        REGLPF has been properly reset (otherwise, HAL_PWREx_DisableLowPowerRunMode 
+  *        returns HAL_TIMEOUT status). The system clock frequency can then be
+  *        increased above 2 MHz.   
+  * @retval HAL_StatusTypeDef
+  */
+HAL_StatusTypeDef HAL_PWREx_DisableLowPowerRunMode(void)
+{
+  uint32_t wait_loop_index = 0U;
+  
+  /* Exit the Low Power Run mode */
+  CLEAR_BIT(PWR->CR, PWR_CR_LPRUN);
+  CLEAR_BIT(PWR->CR, PWR_CR_LPSDSR);
+  
+  /* Wait until REGLPF is reset */
+  wait_loop_index = (PWR_FLAG_SETTING_DELAY_US * (SystemCoreClock / 1000000U));
+
+  while ((wait_loop_index != 0U) && (HAL_IS_BIT_SET(PWR->CSR, PWR_CSR_REGLPF)))
+  {
+    wait_loop_index--;
+  }
+
+  if (HAL_IS_BIT_SET(PWR->CSR, PWR_CSR_REGLPF))
+  {
+    return HAL_TIMEOUT;
+  }
+
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_tim_ex.c

@@ -0,0 +1,427 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_tim_ex.c
+  * @author  MCD Application Team
+  * @brief   TIM HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the Timer Extended peripheral:
+  *           + Time Master and Slave synchronization configuration
+  *           + Timer remapping capabilities configuration
+  @verbatim
+  ==============================================================================
+                      ##### TIMER Extended features #####
+  ==============================================================================
+  [..]
+    The Timer Extended features include:
+    (#) Synchronization circuit to control the timer with external signals and to
+        interconnect several timers together.
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup TIMEx TIMEx
+  * @brief TIM Extended HAL module driver
+  * @{
+  */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macros ------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Functions TIM Extended Exported Functions
+  * @{
+  */
+/** @defgroup TIMEx_Exported_Functions_Group5 Extended Peripheral Control functions
+  * @brief    Peripheral Control functions
+  *
+@verbatim
+  ==============================================================================
+                    ##### Peripheral Control functions #####
+  ==============================================================================
+  [..]
+    This section provides functions allowing to:
+      (+) Configure Master synchronization.
+      (+) Configure timer remapping capabilities.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Configures the TIM in master mode.
+  * @param  htim TIM handle.
+  * @param  sMasterConfig pointer to a TIM_MasterConfigTypeDef structure that
+  *         contains the selected trigger output (TRGO) and the Master/Slave
+  *         mode.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim,
+                                                        TIM_MasterConfigTypeDef *sMasterConfig)
+{
+  uint32_t tmpcr2;
+  uint32_t tmpsmcr;
+
+  /* Check the parameters */
+  assert_param(IS_TIM_MASTER_INSTANCE(htim->Instance));
+  assert_param(IS_TIM_TRGO_SOURCE(sMasterConfig->MasterOutputTrigger));
+  assert_param(IS_TIM_MSM_STATE(sMasterConfig->MasterSlaveMode));
+
+  /* Check input state */
+  __HAL_LOCK(htim);
+
+  /* Change the handler state */
+  htim->State = HAL_TIM_STATE_BUSY;
+
+  /* Get the TIMx CR2 register value */
+  tmpcr2 = htim->Instance->CR2;
+
+  /* Get the TIMx SMCR register value */
+  tmpsmcr = htim->Instance->SMCR;
+
+  /* Reset the MMS Bits */
+  tmpcr2 &= ~TIM_CR2_MMS;
+  /* Select the TRGO source */
+  tmpcr2 |=  sMasterConfig->MasterOutputTrigger;
+
+  /* Update TIMx CR2 */
+  htim->Instance->CR2 = tmpcr2;
+
+  if (IS_TIM_SLAVE_INSTANCE(htim->Instance))
+  {
+    /* Reset the MSM Bit */
+    tmpsmcr &= ~TIM_SMCR_MSM;
+    /* Set master mode */
+    tmpsmcr |= sMasterConfig->MasterSlaveMode;
+
+    /* Update TIMx SMCR */
+    htim->Instance->SMCR = tmpsmcr;
+  }
+
+  /* Change the htim state */
+  htim->State = HAL_TIM_STATE_READY;
+
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Configures the TIMx Remapping input capabilities.
+  @if STM32L073xx
+  * @note   It is not possible to connect TIM2 and TIM21 on PB5(AF4) at the same time.
+  *         When selecting TIM3_TI2_GPIOB5_AF4, Channel2 of TIM3 will be
+  *         connected to PB5(AF4) and Channel2 of TIM21 will be connected to
+  *         some other GPIOs. (refer to alternate functions for more details)
+  *         When selecting TIM3_TI2_GPIO_DEF, Channel2 of Timer 3 will be
+  *         connected an GPIO (other than PB5(AF4)) and Channel2 of TIM21
+  *         will be connected to PB5(AF4).
+  * @note   When TIM2 ETR is fed with HSI48, this ETR must be prescaled internally
+  *         to the TIMER2 because the maximum system frequency is 32 MHz
+  @endif
+  * @param  htim TIM handle.
+  * @param  Remap specifies the TIM remapping source.
+  @if STM32L073xx
+  *         For TIM2, the parameter is a combination of 2 fields (field1 | field2):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM2_ETR_GPIO:      TIM2  ETR connected to GPIO (default):
+  *                                    PA0(AF5) or PA5(AF2) or PA15(AF2) or PE9(AF2)
+  *           @arg TIM2_ETR_HSI48:     TIM2  ETR connected to HSI48
+  *           @arg TIM2_ETR_HSI16:     TIM2  ETR connected to HSI16
+  *           @arg TIM2_ETR_LSE:       TIM2  ETR connected to LSE
+  *           @arg TIM2_ETR_COMP2_OUT: TIM2  ETR connected to COMP2 output
+  *           @arg TIM2_ETR_COMP1_OUT: TIM2  ETR connected to COMP1 output
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM2_TI4_GPIO :     TIM2  TI4 connected to GPIO1(default):
+  *                                    PA3(AF2) or PB11(AF2) or PE12(AF0)
+  *           @arg TIM2_TI4_COMP1:     TIM2  TI4 connected to COMP1
+  *           @arg TIM2_TI4_COMP2:     TIM2  TI4 connected to COMP2
+  @endif
+  @if STM32L031xx
+  *         For TIM2, the parameter is a combination of 2 fields (field1 | field2):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM2_ETR_GPIO:      TIM2  ETR connected to GPIO (default):
+  *                                    PA0(AF5) or PA5(AF2) or PA15(AF2)
+  *           @arg TIM2_ETR_HSI16:     TIM2  ETR connected to HS16 (HSIOUT)
+  *           @arg TIM2_ETR_LSE:       TIM2  ETR connected to LSE
+  *           @arg TIM2_ETR_COMP2_OUT: TIM2  ETR connected to COMP2 output
+  *           @arg TIM2_ETR_COMP1_OUT: TIM2  ETR connected to COMP1 output
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM2_TI4_GPIO :     TIM2  TI4 connected to GPIO (default):
+  *                                    PA3(AF2) or PB11(AF2) or PB1(AF5)
+  *           @arg TIM2_TI4_COMP1_OUT: TIM2  TI4 connected to COMP1 output
+  *           @arg TIM2_TI4_COMP2_OUT: TIM2  TI4 connected to COMP2 output
+  @endif
+  @if STM32L011xx
+  *         For TIM2, the parameter is a combination of 2 fields (field1 | field2):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM2_ETR_GPIO:      TIM2  ETR connected to GPIO (default):
+  *                                    PA0(AF5) or PA5(AF2) or PA15(AF2)
+  *           @arg TIM2_ETR_HSI16:     TIM2  ETR connected to HS16 (HSIOUT)
+  *           @arg TIM2_ETR_LSE:       TIM2  ETR connected to LSE
+  *           @arg TIM2_ETR_COMP2_OUT: TIM2  ETR connected to COMP2 output
+  *           @arg TIM2_ETR_COMP1_OUT: TIM2  ETR connected to COMP1 output
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM2_TI4_GPIO :     TIM2  TI4 connected to GPIO (default):
+  *                                    PA3(AF2) or PB11(AF2) or PB1(AF5)
+  *           @arg TIM2_TI4_COMP1_OUT: TIM2  TI4 connected to COMP1 output
+  *           @arg TIM2_TI4_COMP2_OUT: TIM2  TI4 connected to COMP2 output
+  @endif
+  @if STM32L051xx
+  *         For TIM2, the parameter is a combination of 2 fields (field1 | field2):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM2_ETR_GPIO:      TIM2  ETR connected to GPIO (default):
+  *                                    PA0(AF5) or PA5(AF2) or PA15(AF2) or PE9(AF2)
+  *           @arg TIM2_ETR_HSI48:     TIM2  ETR connected to HSI48
+  *           @arg TIM2_ETR_LSE:       TIM2  ETR connected to LSE
+  *           @arg TIM2_ETR_COMP2_OUT: TIM2  ETR connected to COMP2 output
+  *           @arg TIM2_ETR_COMP1_OUT: TIM2  ETR connected to COMP1 output
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM2_TI4_GPIO:      TIM2  TI4 connected to GPIO1(default):
+  *                                    PA3(AF2) or PB11(AF2) or PE12(AF0)
+  *           @arg TIM2_TI4_COMP1:     TIM2  TI4 connected to COMP1
+  *           @arg TIM2_TI4_COMP2:     TIM2  TI4 connected to COMP2
+  *           @arg TIM2_TI4_GPIO2:     TIM2  TI4 connected to GPIO2 :
+  *                                    PA3(AF2) or PB11(AF2) or PE12(AF0)
+  @endif
+  @if STM32L073xx
+  *
+  *         For TIM3, the parameter is a combination of 4 fields (field1 | field2 | field3 | field4):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM3_ETR_GPIO:      TIM3  ETR connected to GPIO (default):
+  *                                    PE2(AF2) or PD2(AF2) or PE2(AF2)
+  *           @arg TIM3_ETR_HSI:       TIM3 ETR connected to HSI
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM3_TI1_USB_SOF:   TIM3 TI1 connected to USB_SOF (default)
+  *           @arg TIM3_TI1_GPIO:      TIM3 TI1 connected to GPIO :
+  *                                    PE3(AF2) or PA6(AF2) or PC6(AF2) or PB4(AF2)
+  *
+  *                   field3 can have the following values:
+  *           @arg TIM3_TI2_GPIOB5_AF4:TIM3 TI3 connected to P5(AF4)
+  *                                    (refer to note)
+  *           @arg TIM3_TI2_GPIO_DEF:  TIM3 TI3 connected to GPIO (default):
+  *                                    PA7(AF2) or PB5(AF4) or PC7(AF2) or PE7(AF2)
+  *
+  *                   field4 can have the following values:
+  *           @arg TIM3_TI4_GPIO_DEF:  TIM3 TI4 connected to GPIO:
+  *                                    PB1(AF2) or PE6(AF2)
+  *           @arg TIM3_TI4_GPIOC9_AF2:TIM3 TI4 connected to PC9(AF)2
+  @endif
+  @if STM32L073xx
+  *         For TIM21, the parameter is a combination of 3 fields (field1 | field2 | field3):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM21_ETR_GPIO:     TIM21 ETR connected to GPIO(default) :
+  *                                    PC9(AF0) or PA1(AF5)
+  *           @arg TIM21_ETR_COMP2_OUT:TIM21 ETR connected to COMP2 output
+  *           @arg TIM21_ETR_COMP1_OUT:TIM21 ETR connected to COMP1 output
+  *           @arg TIM21_ETR_LSE:      TIM21 ETR connected to LSE
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM21_TI1_MCO:      TIM21 TI1 connected to MCO
+  *           @arg TIM21_TI1_RTC_WKUT_IT: TIM21 TI1 connected to RTC WAKEUP interrupt
+  *           @arg TIM21_TI1_HSE_RTC:  TIM21 TI1 connected to HSE_RTC
+  *           @arg TIM21_TI1_MSI:      TIM21 TI1 connected to MSI clock
+  *           @arg TIM21_TI1_LSE:      TIM21 TI1 connected to LSE
+  *           @arg TIM21_TI1_LSI:      TIM21 TI1 connected to LSI
+  *           @arg TIM21_TI1_COMP1_OUT:TIM21 TI1 connected to COMP1_OUT
+  *           @arg TIM21_TI1_GPIO:     TIM21 TI1 connected to GPIO(default):
+  *                                    PA2(AF0) or PB13(AF6) or PE5(AF0) or PD0(AF0)
+  *
+  *                   field3 can have the following values:
+  *           @arg TIM21_TI2_GPIO:     TIM21 TI2 connected to GPIO(default):
+  *                                    PA3(AF0) or PB14(AF6) or PE6(AF0) or PD7(AF1)
+  *           @arg TIM21_TI2_COMP2_OUT:TIM21 TI2 connected to COMP2 output
+  @endif
+  @if STM32L031xx
+  *         For TIM21, the parameter is a combination of 3 fields (field1 | field2 | field3):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM21_ETR_GPIO:     TIM21 ETR connected to GPIO(default) :
+  *                                    PA1(AF5)
+  *           @arg TIM21_ETR_COMP2_OUT:TIM21 ETR connected to COMP2 output
+  *           @arg TIM21_ETR_COMP1_OUT:TIM21 ETR connected to COMP1 output
+  *           @arg TIM21_ETR_LSE:      TIM21 ETR connected to LSE
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM21_TI1_MCO:      TIM21 TI1 connected to MCO
+  *           @arg TIM21_TI1_RTC_WKUT_IT: TIM21 TI1 connected to RTC WAKEUP interrupt
+  *           @arg TIM21_TI1_HSE_RTC:  TIM21 TI1 connected to HSE_RTC
+  *           @arg TIM21_TI1_MSI:      TIM21 TI1 connected to MSI clock
+  *           @arg TIM21_TI1_LSE:      TIM21 TI1 connected to LSE
+  *           @arg TIM21_TI1_LSI:      TIM21 TI1 connected to LSI
+  *           @arg TIM21_TI1_COMP1_OUT:TIM21 TI1 connected to COMP1_OUT
+  *
+  *                   field3 can have the following values:
+  *           @arg TIM21_TI2_GPIO:     TIM21 TI2 connected to GPIO(default):
+  *                                    PA3(AF0) or PB14(AF6)
+  *           @arg TIM21_TI2_COMP2_OUT:TIM21 TI2 connected to COMP2 output
+  @endif
+  @if STM32L011xx
+  *         For TIM21, the parameter is a combination of 3 fields (field1 | field2 | field3):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM21_ETR_GPIO:     TIM21 ETR connected to GPIO(default) :
+  *                                    PA1(AF5)
+  *           @arg TIM21_ETR_COMP2_OUT:TIM21 ETR connected to COMP2 output
+  *           @arg TIM21_ETR_COMP1_OUT:TIM21 ETR connected to COMP1 output
+  *           @arg TIM21_ETR_LSE:      TIM21 ETR connected to LSE
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM21_TI1_MCO:      TIM21 TI1 connected to MCO
+  *           @arg TIM21_TI1_RTC_WKUT_IT: TIM21 TI1 connected to RTC WAKEUP interrupt
+  *           @arg TIM21_TI1_HSE_RTC:  TIM21 TI1 connected to HSE_RTC
+  *           @arg TIM21_TI1_MSI:      TIM21 TI1 connected to MSI clock
+  *           @arg TIM21_TI1_LSE:      TIM21 TI1 connected to LSE
+  *           @arg TIM21_TI1_LSI:      TIM21 TI1 connected to LSI
+  *           @arg TIM21_TI1_COMP1_OUT:TIM21 TI1 connected to COMP1_OUT
+  *
+  *                   field3 can have the following values:
+  *           @arg TIM21_TI2_GPIO:     TIM21 TI2 connected to GPIO(default):
+  *                                    PA3(AF0) or PB14(AF6)
+  *           @arg TIM21_TI2_COMP2_OUT:TIM21 TI2 connected to COMP2 output
+  @endif
+  @if STM32L051xx
+  *         For TIM21, the parameter is a combination of 3 fields (field1 | field2 | field3):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM21_ETR_GPIO:     TIM21 ETR connected to GPIO(default) :
+  *                                    PC9(AF0) or PA1(AF5)
+  *           @arg TIM21_ETR_COMP2_OUT:TIM21 ETR connected to COMP2 output
+  *           @arg TIM21_ETR_COMP1_OUT:TIM21 ETR connected to COMP1 output
+  *           @arg TIM21_ETR_LSE:      TIM21 ETR connected to LSE
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM21_TI1_MCO:      TIM21 TI1 connected to MCO
+  *           @arg TIM21_TI1_RTC_WKUT_IT: TIM21 TI1 connected to RTC WAKEUP interrupt
+  *           @arg TIM21_TI1_HSE_RTC:  TIM21 TI1 connected to HSE_RTC
+  *           @arg TIM21_TI1_MSI:      TIM21 TI1 connected to MSI clock
+  *           @arg TIM21_TI1_LSE:      TIM21 TI1 connected to LSE
+  *           @arg TIM21_TI1_LSI:      TIM21 TI1 connected to LSI
+  *           @arg TIM21_TI1_COMP1_OUT:TIM21 TI1 connected to COMP1_OUT
+  *           @arg TIM21_TI1_GPIO:     TIM21 TI1 connected to GPIO(default):
+  *                                    PA2(AF0) or PB13(AF6) or PE5(AF0) or PD0(AF0)
+  *
+  *                   field3 can have the following values:
+  *           @arg TIM21_TI2_GPIO:     TIM21 TI2 connected to GPIO(default):
+  *                                    PA3(AF0) or PB14(AF6) or PE6(AF0) or PD7(AF1)
+  *           @arg TIM21_TI2_COMP2_OUT:TIM21 TI2 connected to COMP2 output
+  @endif
+  @if STM32L073xx
+  *
+  *         For TIM22, the parameter can have the following values:
+  *           @arg TIM22_ETR_LSE:      TIM22 ETR connected to LSE
+  *           @arg TIM22_ETR_COMP2_OUT:TIM22 ETR connected to COMP2 output
+  *           @arg TIM22_ETR_COMP1_OUT:TIM22 ETR connected to COMP1 output
+  *           @arg TIM22_ETR_GPIO:     TIM22 ETR connected to GPIO(default):
+  *                                    PC8(AF0) or PA4(AF5)
+  *           @arg TIM22_TI1_GPIO:     TIM22 TI1 connected to GPIO(default):
+  *                                    PC6(AF0) or PA6(AF5) or PB4(AF4) or PE0(AF3)
+  *           @arg TIM22_TI1_COMP2_OUT:TIM22 TI1 connected to COMP2 output
+  *           @arg TIM22_TI1_COMP1_OUT:TIM22 TI1 connected to COMP1 output
+  @endif
+  @if STM32L031xx
+  *
+  *         For TIM22, the parameter is a combination of 2 fields (field1 | field2):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM22_ETR_LSE:      TIM22 ETR connected to LSE
+  *           @arg TIM22_ETR_COMP2_OUT:TIM22 ETR connected to COMP2 output
+  *           @arg TIM22_ETR_COMP1_OUT:TIM22 ETR connected to COMP1 output
+  *           @arg TIM22_ETR_GPIO:     TIM22 ETR connected to GPIO(default):
+  *                                    PA4(AF5)
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM22_TI1_GPIO:     TIM22 TI1 connected to GPIO(default):
+  *                                    PC0(AF6) or PA5(AF6) or PB4(AF4)
+  *           @arg TIM22_TI1_COMP2_OUT:TIM22 TI1 connected to COMP2 output
+  *           @arg TIM22_TI1_COMP1_OUT:TIM22 TI1 connected to COMP1 output
+  *
+  @endif
+  @if STM32L051xx
+  *
+  *         For TIM22, the parameter is a combination of 2 fields (field1 | field2):
+  *
+  *                   field1 can have the following values:
+  *           @arg TIM22_ETR_LSE:      TIM22 ETR connected to LSE
+  *           @arg TIM22_ETR_COMP2_OUT:TIM22 ETR connected to COMP2 output
+  *           @arg TIM22_ETR_COMP1_OUT:TIM22 ETR connected to COMP1 output
+  *           @arg TIM22_ETR_GPIO:     TIM22 ETR connected to GPIO(default):
+  *                                    PC8(AF0) or PA4(AF5)
+  *
+  *                   field2 can have the following values:
+  *           @arg TIM22_TI1_GPIO:     TIM22 TI1 connected to GPIO(default):
+  *                                    PC6(AF0) or PA6(AF5) or PB4(AF4) or PE0(AF3)
+  *           @arg TIM22_TI1_COMP2_OUT:TIM22 TI1 connected to COMP2 output
+  *           @arg TIM22_TI1_COMP1_OUT:TIM22 TI1 connected to COMP1 output
+  @endif
+  *
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef *htim, uint32_t Remap)
+{
+  __HAL_LOCK(htim);
+
+  /* Check parameters */
+  assert_param(IS_TIM_REMAP(htim->Instance, Remap));
+
+  /* Set the Timer remapping configuration */
+  WRITE_REG(htim->Instance->OR, Remap);
+
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+
+#endif /* HAL_TIM_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

fw_hal/Drivers/STM32L0xx_HAL_Driver/Src/stm32l0xx_hal_uart_ex.c

@@ -0,0 +1,842 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_uart_ex.c
+  * @author  MCD Application Team
+  * @brief   Extended UART HAL module driver.
+  *          This file provides firmware functions to manage the following extended
+  *          functionalities of the Universal Asynchronous Receiver Transmitter Peripheral (UART).
+  *           + Initialization and de-initialization functions
+  *           + Peripheral Control functions
+  *
+  *
+  @verbatim
+  ==============================================================================
+               ##### UART peripheral extended features  #####
+  ==============================================================================
+
+    (#) Declare a UART_HandleTypeDef handle structure.
+
+    (#) For the UART RS485 Driver Enable mode, initialize the UART registers
+        by calling the HAL_RS485Ex_Init() API.
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup UARTEx UARTEx
+  * @brief UART Extended HAL module driver
+  * @{
+  */
+
+#ifdef HAL_UART_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+
+/* Private macros ------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/** @defgroup UARTEx_Private_Functions UARTEx Private Functions
+  * @{
+  */
+static void UARTEx_Wakeup_AddressConfig(UART_HandleTypeDef *huart, UART_WakeUpTypeDef WakeUpSelection);
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @defgroup UARTEx_Exported_Functions  UARTEx Exported Functions
+  * @{
+  */
+
+/** @defgroup UARTEx_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @brief    Extended Initialization and Configuration Functions
+  *
+@verbatim
+===============================================================================
+            ##### Initialization and Configuration functions #####
+ ===============================================================================
+    [..]
+    This subsection provides a set of functions allowing to initialize the USARTx or the UARTy
+    in asynchronous mode.
+      (+) For the asynchronous mode the parameters below can be configured:
+        (++) Baud Rate
+        (++) Word Length
+        (++) Stop Bit
+        (++) Parity: If the parity is enabled, then the MSB bit of the data written
+             in the data register is transmitted but is changed by the parity bit.
+        (++) Hardware flow control
+        (++) Receiver/transmitter modes
+        (++) Over Sampling Method
+        (++) One-Bit Sampling Method
+      (+) For the asynchronous mode, the following advanced features can be configured as well:
+        (++) TX and/or RX pin level inversion
+        (++) data logical level inversion
+        (++) RX and TX pins swap
+        (++) RX overrun detection disabling
+        (++) DMA disabling on RX error
+        (++) MSB first on communication line
+        (++) auto Baud rate detection
+    [..]
+    The HAL_RS485Ex_Init() API follows the UART RS485 mode configuration
+     procedures (details for the procedures are available in reference manual).
+
+@endverbatim
+
+  Depending on the frame length defined by the M1 and M0 bits (7-bit,
+  8-bit or 9-bit), the possible UART formats are listed in the
+  following table.
+
+    Table 1. UART frame format.
+    +-----------------------------------------------------------------------+
+    |  M1 bit |  M0 bit |  PCE bit  |             UART frame                |
+    |---------|---------|-----------|---------------------------------------|
+    |    0    |    0    |    0      |    | SB |    8 bit data   | STB |     |
+    |---------|---------|-----------|---------------------------------------|
+    |    0    |    0    |    1      |    | SB | 7 bit data | PB | STB |     |
+    |---------|---------|-----------|---------------------------------------|
+    |    0    |    1    |    0      |    | SB |    9 bit data   | STB |     |
+    |---------|---------|-----------|---------------------------------------|
+    |    0    |    1    |    1      |    | SB | 8 bit data | PB | STB |     |
+    |---------|---------|-----------|---------------------------------------|
+    |    1    |    0    |    0      |    | SB |    7 bit data   | STB |     |
+    |---------|---------|-----------|---------------------------------------|
+    |    1    |    0    |    1      |    | SB | 6 bit data | PB | STB |     |
+    +-----------------------------------------------------------------------+
+
+  * @{
+  */
+
+/**
+  * @brief Initialize the RS485 Driver enable feature according to the specified
+  *         parameters in the UART_InitTypeDef and creates the associated handle.
+  * @param huart            UART handle.
+  * @param Polarity         Select the driver enable polarity.
+  *          This parameter can be one of the following values:
+  *          @arg @ref UART_DE_POLARITY_HIGH DE signal is active high
+  *          @arg @ref UART_DE_POLARITY_LOW  DE signal is active low
+  * @param AssertionTime    Driver Enable assertion time:
+  *       5-bit value defining the time between the activation of the DE (Driver Enable)
+  *       signal and the beginning of the start bit. It is expressed in sample time
+  *       units (1/8 or 1/16 bit time, depending on the oversampling rate)
+  * @param DeassertionTime  Driver Enable deassertion time:
+  *       5-bit value defining the time between the end of the last stop bit, in a
+  *       transmitted message, and the de-activation of the DE (Driver Enable) signal.
+  *       It is expressed in sample time units (1/8 or 1/16 bit time, depending on the
+  *       oversampling rate).
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_RS485Ex_Init(UART_HandleTypeDef *huart, uint32_t Polarity, uint32_t AssertionTime,
+                                   uint32_t DeassertionTime)
+{
+  uint32_t temp;
+
+  /* Check the UART handle allocation */
+  if (huart == NULL)
+  {
+    return HAL_ERROR;
+  }
+  /* Check the Driver Enable UART instance */
+  assert_param(IS_UART_DRIVER_ENABLE_INSTANCE(huart->Instance));
+
+  /* Check the Driver Enable polarity */
+  assert_param(IS_UART_DE_POLARITY(Polarity));
+
+  /* Check the Driver Enable assertion time */
+  assert_param(IS_UART_ASSERTIONTIME(AssertionTime));
+
+  /* Check the Driver Enable deassertion time */
+  assert_param(IS_UART_DEASSERTIONTIME(DeassertionTime));
+
+  if (huart->gState == HAL_UART_STATE_RESET)
+  {
+    /* Allocate lock resource and initialize it */
+    huart->Lock = HAL_UNLOCKED;
+
+#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
+    UART_InitCallbacksToDefault(huart);
+
+    if (huart->MspInitCallback == NULL)
+    {
+      huart->MspInitCallback = HAL_UART_MspInit;
+    }
+
+    /* Init the low level hardware */
+    huart->MspInitCallback(huart);
+#else
+    /* Init the low level hardware : GPIO, CLOCK, CORTEX */
+    HAL_UART_MspInit(huart);
+#endif /* (USE_HAL_UART_REGISTER_CALLBACKS) */
+  }
+
+  huart->gState = HAL_UART_STATE_BUSY;
+
+  /* Disable the Peripheral */
+  __HAL_UART_DISABLE(huart);
+
+  /* Set the UART Communication parameters */
+  if (UART_SetConfig(huart) == HAL_ERROR)
+  {
+    return HAL_ERROR;
+  }
+
+  if (huart->AdvancedInit.AdvFeatureInit != UART_ADVFEATURE_NO_INIT)
+  {
+    UART_AdvFeatureConfig(huart);
+  }
+
+  /* Enable the Driver Enable mode by setting the DEM bit in the CR3 register */
+  SET_BIT(huart->Instance->CR3, USART_CR3_DEM);
+
+  /* Set the Driver Enable polarity */
+  MODIFY_REG(huart->Instance->CR3, USART_CR3_DEP, Polarity);
+
+  /* Set the Driver Enable assertion and deassertion times */
+  temp = (AssertionTime << UART_CR1_DEAT_ADDRESS_LSB_POS);
+  temp |= (DeassertionTime << UART_CR1_DEDT_ADDRESS_LSB_POS);
+  MODIFY_REG(huart->Instance->CR1, (USART_CR1_DEDT | USART_CR1_DEAT), temp);
+
+  /* Enable the Peripheral */
+  __HAL_UART_ENABLE(huart);
+
+  /* TEACK and/or REACK to check before moving huart->gState and huart->RxState to Ready */
+  return (UART_CheckIdleState(huart));
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup UARTEx_Exported_Functions_Group2 IO operation functions
+  *  @brief Extended functions
+  *
+@verbatim
+ ===============================================================================
+                      ##### IO operation functions #####
+ ===============================================================================
+    This subsection provides a set of Wakeup and FIFO mode related callback functions.
+
+    (#) Wakeup from Stop mode Callback:
+        (+) HAL_UARTEx_WakeupCallback()
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief UART wakeup from Stop mode callback.
+  * @param huart UART handle.
+  * @retval None
+  */
+__weak void HAL_UARTEx_WakeupCallback(UART_HandleTypeDef *huart)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(huart);
+
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_UARTEx_WakeupCallback can be implemented in the user file.
+   */
+}
+
+
+/**
+  * @}
+  */
+
+/** @defgroup UARTEx_Exported_Functions_Group3 Peripheral Control functions
+  * @brief    Extended Peripheral Control functions
+  *
+@verbatim
+ ===============================================================================
+                      ##### Peripheral Control functions #####
+ ===============================================================================
+    [..] This section provides the following functions:
+     (+) HAL_UARTEx_EnableClockStopMode() API enables the UART clock (HSI or LSE only) during stop mode
+     (+) HAL_UARTEx_DisableClockStopMode() API disables the above functionality
+     (+) HAL_MultiProcessorEx_AddressLength_Set() API optionally sets the UART node address
+         detection length to more than 4 bits for multiprocessor address mark wake up.
+     (+) HAL_UARTEx_StopModeWakeUpSourceConfig() API defines the wake-up from stop mode
+         trigger: address match, Start Bit detection or RXNE bit status.
+     (+) HAL_UARTEx_EnableStopMode() API enables the UART to wake up the MCU from stop mode
+     (+) HAL_UARTEx_DisableStopMode() API disables the above functionality
+
+    [..] This subsection also provides a set of additional functions providing enhanced reception
+    services to user. (For example, these functions allow application to handle use cases
+    where number of data to be received is unknown).
+
+    (#) Compared to standard reception services which only consider number of received
+        data elements as reception completion criteria, these functions also consider additional events
+        as triggers for updating reception status to caller :
+       (+) Detection of inactivity period (RX line has not been active for a given period).
+          (++) RX inactivity detected by IDLE event, i.e. RX line has been in idle state (normally high state)
+               for 1 frame time, after last received byte.
+          (++) RX inactivity detected by RTO, i.e. line has been in idle state
+               for a programmable time, after last received byte.
+       (+) Detection that a specific character has been received.
+
+    (#) There are two mode of transfer:
+       (+) Blocking mode: The reception is performed in polling mode, until either expected number of data is received,
+           or till IDLE event occurs. Reception is handled only during function execution.
+           When function exits, no data reception could occur. HAL status and number of actually received data elements,
+           are returned by function after finishing transfer.
+       (+) Non-Blocking mode: The reception is performed using Interrupts or DMA.
+           These API's return the HAL status.
+           The end of the data processing will be indicated through the
+           dedicated UART IRQ when using Interrupt mode or the DMA IRQ when using DMA mode.
+           The HAL_UARTEx_RxEventCallback() user callback will be executed during Receive process
+           The HAL_UART_ErrorCallback()user callback will be executed when a reception error is detected.
+
+    (#) Blocking mode API:
+        (+) HAL_UARTEx_ReceiveToIdle()
+
+    (#) Non-Blocking mode API with Interrupt:
+        (+) HAL_UARTEx_ReceiveToIdle_IT()
+
+    (#) Non-Blocking mode API with DMA:
+        (+) HAL_UARTEx_ReceiveToIdle_DMA()
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Keep UART Clock enabled when in Stop Mode.
+  * @note   When the USART clock source is configured to be LSE or HSI, it is possible to keep enabled
+  *         this clock during STOP mode by setting the UCESM bit in USART_CR3 control register.
+  * @note   When LPUART is used to wakeup from stop with LSE is selected as LPUART clock source,
+  *         and desired baud rate is 9600 baud, the bit UCESM bit in LPUART_CR3 control register must be set.
+  * @param  huart UART handle.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_EnableClockStopMode(UART_HandleTypeDef *huart)
+{
+  /* Process Locked */
+  __HAL_LOCK(huart);
+
+  /* Set UCESM bit */
+  ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_UCESM);
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(huart);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Disable UART Clock when in Stop Mode.
+  * @param  huart UART handle.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_DisableClockStopMode(UART_HandleTypeDef *huart)
+{
+  /* Process Locked */
+  __HAL_LOCK(huart);
+
+  /* Clear UCESM bit */
+  ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_UCESM);
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(huart);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief By default in multiprocessor mode, when the wake up method is set
+  *        to address mark, the UART handles only 4-bit long addresses detection;
+  *        this API allows to enable longer addresses detection (6-, 7- or 8-bit
+  *        long).
+  * @note  Addresses detection lengths are: 6-bit address detection in 7-bit data mode,
+  *        7-bit address detection in 8-bit data mode, 8-bit address detection in 9-bit data mode.
+  * @param huart         UART handle.
+  * @param AddressLength This parameter can be one of the following values:
+  *          @arg @ref UART_ADDRESS_DETECT_4B 4-bit long address
+  *          @arg @ref UART_ADDRESS_DETECT_7B 6-, 7- or 8-bit long address
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_MultiProcessorEx_AddressLength_Set(UART_HandleTypeDef *huart, uint32_t AddressLength)
+{
+  /* Check the UART handle allocation */
+  if (huart == NULL)
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check the address length parameter */
+  assert_param(IS_UART_ADDRESSLENGTH_DETECT(AddressLength));
+
+  huart->gState = HAL_UART_STATE_BUSY;
+
+  /* Disable the Peripheral */
+  __HAL_UART_DISABLE(huart);
+
+  /* Set the address length */
+  MODIFY_REG(huart->Instance->CR2, USART_CR2_ADDM7, AddressLength);
+
+  /* Enable the Peripheral */
+  __HAL_UART_ENABLE(huart);
+
+  /* TEACK and/or REACK to check before moving huart->gState to Ready */
+  return (UART_CheckIdleState(huart));
+}
+
+/**
+  * @brief Set Wakeup from Stop mode interrupt flag selection.
+  * @note It is the application responsibility to enable the interrupt used as
+  *       usart_wkup interrupt source before entering low-power mode.
+  * @param huart           UART handle.
+  * @param WakeUpSelection Address match, Start Bit detection or RXNE/RXFNE bit status.
+  *          This parameter can be one of the following values:
+  *          @arg @ref UART_WAKEUP_ON_ADDRESS
+  *          @arg @ref UART_WAKEUP_ON_STARTBIT
+  *          @arg @ref UART_WAKEUP_ON_READDATA_NONEMPTY
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_StopModeWakeUpSourceConfig(UART_HandleTypeDef *huart, UART_WakeUpTypeDef WakeUpSelection)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+  uint32_t tickstart;
+
+  /* check the wake-up from stop mode UART instance */
+  assert_param(IS_UART_WAKEUP_FROMSTOP_INSTANCE(huart->Instance));
+  /* check the wake-up selection parameter */
+  assert_param(IS_UART_WAKEUP_SELECTION(WakeUpSelection.WakeUpEvent));
+
+  /* Process Locked */
+  __HAL_LOCK(huart);
+
+  huart->gState = HAL_UART_STATE_BUSY;
+
+  /* Disable the Peripheral */
+  __HAL_UART_DISABLE(huart);
+
+  /* Set the wake-up selection scheme */
+  MODIFY_REG(huart->Instance->CR3, USART_CR3_WUS, WakeUpSelection.WakeUpEvent);
+
+  if (WakeUpSelection.WakeUpEvent == UART_WAKEUP_ON_ADDRESS)
+  {
+    UARTEx_Wakeup_AddressConfig(huart, WakeUpSelection);
+  }
+
+  /* Enable the Peripheral */
+  __HAL_UART_ENABLE(huart);
+
+  /* Init tickstart for timeout management */
+  tickstart = HAL_GetTick();
+
+  /* Wait until REACK flag is set */
+  if (UART_WaitOnFlagUntilTimeout(huart, USART_ISR_REACK, RESET, tickstart, HAL_UART_TIMEOUT_VALUE) != HAL_OK)
+  {
+    status = HAL_TIMEOUT;
+  }
+  else
+  {
+    /* Initialize the UART State */
+    huart->gState = HAL_UART_STATE_READY;
+  }
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(huart);
+
+  return status;
+}
+
+/**
+  * @brief Enable UART Stop Mode.
+  * @note The UART is able to wake up the MCU from Stop 1 mode as long as UART clock is HSI or LSE.
+  * @param huart UART handle.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_EnableStopMode(UART_HandleTypeDef *huart)
+{
+  /* Process Locked */
+  __HAL_LOCK(huart);
+
+  /* Set UESM bit */
+  ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_UESM);
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(huart);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief Disable UART Stop Mode.
+  * @param huart UART handle.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_DisableStopMode(UART_HandleTypeDef *huart)
+{
+  /* Process Locked */
+  __HAL_LOCK(huart);
+
+  /* Clear UESM bit */
+  ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_UESM);
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(huart);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief Receive an amount of data in blocking mode till either the expected number of data
+  *        is received or an IDLE event occurs.
+  * @note  HAL_OK is returned if reception is completed (expected number of data has been received)
+  *        or if reception is stopped after IDLE event (less than the expected number of data has been received)
+  *        In this case, RxLen output parameter indicates number of data available in reception buffer.
+  * @note  When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+  *        the received data is handled as a set of uint16_t. In this case, Size must indicate the number
+  *        of uint16_t available through pData.
+  * @note   When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+  *         address of user data buffer for storing data to be received, should be aligned on a half word frontier
+  *         (16 bits) (as received data will be handled using uint16_t pointer cast). Depending on compilation chain,
+  *         use of specific alignment compilation directives or pragmas might be required to ensure proper
+  *         alignment for pData.
+  * @param huart   UART handle.
+  * @param pData   Pointer to data buffer (uint8_t or uint16_t data elements).
+  * @param Size    Amount of data elements (uint8_t or uint16_t) to be received.
+  * @param RxLen   Number of data elements finally received
+  *                (could be lower than Size, in case reception ends on IDLE event)
+  * @param Timeout Timeout duration expressed in ms (covers the whole reception sequence).
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint16_t *RxLen,
+                                           uint32_t Timeout)
+{
+  uint8_t  *pdata8bits;
+  uint16_t *pdata16bits;
+  uint16_t uhMask;
+  uint32_t tickstart;
+
+  /* Check that a Rx process is not already ongoing */
+  if (huart->RxState == HAL_UART_STATE_READY)
+  {
+    if ((pData == NULL) || (Size == 0U))
+    {
+      return  HAL_ERROR;
+    }
+
+    /* In case of 9bits/No Parity transfer, pData buffer provided as input parameter
+       should be aligned on a uint16_t frontier, as data to be received from RDR will be
+       handled through a uint16_t cast. */
+    if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE))
+    {
+      if ((((uint32_t)pData) & 1U) != 0U)
+      {
+        return  HAL_ERROR;
+      }
+    }
+
+    __HAL_LOCK(huart);
+
+    huart->ErrorCode = HAL_UART_ERROR_NONE;
+    huart->RxState = HAL_UART_STATE_BUSY_RX;
+    huart->ReceptionType = HAL_UART_RECEPTION_TOIDLE;
+
+    /* Init tickstart for timeout management */
+    tickstart = HAL_GetTick();
+
+    huart->RxXferSize  = Size;
+    huart->RxXferCount = Size;
+
+    /* Computation of UART mask to apply to RDR register */
+    UART_MASK_COMPUTATION(huart);
+    uhMask = huart->Mask;
+
+    /* In case of 9bits/No Parity transfer, pRxData needs to be handled as a uint16_t pointer */
+    if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE))
+    {
+      pdata8bits  = NULL;
+      pdata16bits = (uint16_t *) pData;
+    }
+    else
+    {
+      pdata8bits  = pData;
+      pdata16bits = NULL;
+    }
+
+    __HAL_UNLOCK(huart);
+
+    /* Initialize output number of received elements */
+    *RxLen = 0U;
+
+    /* as long as data have to be received */
+    while (huart->RxXferCount > 0U)
+    {
+      /* Check if IDLE flag is set */
+      if (__HAL_UART_GET_FLAG(huart, UART_FLAG_IDLE))
+      {
+        /* Clear IDLE flag in ISR */
+        __HAL_UART_CLEAR_FLAG(huart, UART_CLEAR_IDLEF);
+
+        /* If Set, but no data ever received, clear flag without exiting loop */
+        /* If Set, and data has already been received, this means Idle Event is valid : End reception */
+        if (*RxLen > 0U)
+        {
+          huart->RxState = HAL_UART_STATE_READY;
+
+          return HAL_OK;
+        }
+      }
+
+      /* Check if RXNE flag is set */
+      if (__HAL_UART_GET_FLAG(huart, UART_FLAG_RXNE))
+      {
+        if (pdata8bits == NULL)
+        {
+          *pdata16bits = (uint16_t)(huart->Instance->RDR & uhMask);
+          pdata16bits++;
+        }
+        else
+        {
+          *pdata8bits = (uint8_t)(huart->Instance->RDR & (uint8_t)uhMask);
+          pdata8bits++;
+        }
+        /* Increment number of received elements */
+        *RxLen += 1U;
+        huart->RxXferCount--;
+      }
+
+      /* Check for the Timeout */
+      if (Timeout != HAL_MAX_DELAY)
+      {
+        if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
+        {
+          huart->RxState = HAL_UART_STATE_READY;
+
+          return HAL_TIMEOUT;
+        }
+      }
+    }
+
+    /* Set number of received elements in output parameter : RxLen */
+    *RxLen = huart->RxXferSize - huart->RxXferCount;
+    /* At end of Rx process, restore huart->RxState to Ready */
+    huart->RxState = HAL_UART_STATE_READY;
+
+    return HAL_OK;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+
+/**
+  * @brief Receive an amount of data in interrupt mode till either the expected number of data
+  *        is received or an IDLE event occurs.
+  * @note  Reception is initiated by this function call. Further progress of reception is achieved thanks
+  *        to UART interrupts raised by RXNE and IDLE events. Callback is called at end of reception indicating
+  *        number of received data elements.
+  * @note  When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+  *        the received data is handled as a set of uint16_t. In this case, Size must indicate the number
+  *        of uint16_t available through pData.
+  * @note  When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+  *        address of user data buffer for storing data to be received, should be aligned on a half word frontier
+  *        (16 bits) (as received data will be handled using uint16_t pointer cast). Depending on compilation chain,
+  *        use of specific alignment compilation directives or pragmas might be required
+  *        to ensure proper alignment for pData.
+  * @param huart UART handle.
+  * @param pData Pointer to data buffer (uint8_t or uint16_t data elements).
+  * @param Size  Amount of data elements (uint8_t or uint16_t) to be received.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size)
+{
+  HAL_StatusTypeDef status;
+
+  /* Check that a Rx process is not already ongoing */
+  if (huart->RxState == HAL_UART_STATE_READY)
+  {
+    if ((pData == NULL) || (Size == 0U))
+    {
+      return HAL_ERROR;
+    }
+
+    /* In case of 9bits/No Parity transfer, pData buffer provided as input parameter
+       should be aligned on a uint16_t frontier, as data to be received from RDR will be
+       handled through a uint16_t cast. */
+    if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE))
+    {
+      if ((((uint32_t)pData) & 1U) != 0U)
+      {
+        return  HAL_ERROR;
+      }
+    }
+
+    __HAL_LOCK(huart);
+
+    /* Set Reception type to reception till IDLE Event*/
+    huart->ReceptionType = HAL_UART_RECEPTION_TOIDLE;
+
+    status =  UART_Start_Receive_IT(huart, pData, Size);
+
+    /* Check Rx process has been successfully started */
+    if (status == HAL_OK)
+    {
+      if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
+      {
+        __HAL_UART_CLEAR_FLAG(huart, UART_CLEAR_IDLEF);
+        ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+      }
+      else
+      {
+        /* In case of errors already pending when reception is started,
+           Interrupts may have already been raised and lead to reception abortion.
+           (Overrun error for instance).
+           In such case Reception Type has been reset to HAL_UART_RECEPTION_STANDARD. */
+        status = HAL_ERROR;
+      }
+    }
+
+    return status;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+
+/**
+  * @brief Receive an amount of data in DMA mode till either the expected number
+  *        of data is received or an IDLE event occurs.
+  * @note  Reception is initiated by this function call. Further progress of reception is achieved thanks
+  *        to DMA services, transferring automatically received data elements in user reception buffer and
+  *        calling registered callbacks at half/end of reception. UART IDLE events are also used to consider
+  *        reception phase as ended. In all cases, callback execution will indicate number of received data elements.
+  * @note  When the UART parity is enabled (PCE = 1), the received data contain
+  *        the parity bit (MSB position).
+  * @note  When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+  *        the received data is handled as a set of uint16_t. In this case, Size must indicate the number
+  *        of uint16_t available through pData.
+  * @note  When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+  *        address of user data buffer for storing data to be received, should be aligned on a half word frontier
+  *        (16 bits) (as received data will be handled by DMA from halfword frontier). Depending on compilation chain,
+  *        use of specific alignment compilation directives or pragmas might be required
+  *        to ensure proper alignment for pData.
+  * @param huart UART handle.
+  * @param pData Pointer to data buffer (uint8_t or uint16_t data elements).
+  * @param Size  Amount of data elements (uint8_t or uint16_t) to be received.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size)
+{
+  HAL_StatusTypeDef status;
+
+  /* Check that a Rx process is not already ongoing */
+  if (huart->RxState == HAL_UART_STATE_READY)
+  {
+    if ((pData == NULL) || (Size == 0U))
+    {
+      return HAL_ERROR;
+    }
+
+    /* In case of 9bits/No Parity transfer, pData buffer provided as input parameter
+       should be aligned on a uint16_t frontier, as data copy from RDR will be
+       handled by DMA from a uint16_t frontier. */
+    if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE))
+    {
+      if ((((uint32_t)pData) & 1U) != 0U)
+      {
+        return  HAL_ERROR;
+      }
+    }
+
+    __HAL_LOCK(huart);
+
+    /* Set Reception type to reception till IDLE Event*/
+    huart->ReceptionType = HAL_UART_RECEPTION_TOIDLE;
+
+    status =  UART_Start_Receive_DMA(huart, pData, Size);
+
+    /* Check Rx process has been successfully started */
+    if (status == HAL_OK)
+    {
+      if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
+      {
+        __HAL_UART_CLEAR_FLAG(huart, UART_CLEAR_IDLEF);
+        ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+      }
+      else
+      {
+        /* In case of errors already pending when reception is started,
+           Interrupts may have already been raised and lead to reception abortion.
+           (Overrun error for instance).
+           In such case Reception Type has been reset to HAL_UART_RECEPTION_STANDARD. */
+        status = HAL_ERROR;
+      }
+    }
+
+    return status;
+  }
+  else
+  {
+    return HAL_BUSY;
+  }
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup UARTEx_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief Initialize the UART wake-up from stop mode parameters when triggered by address detection.
+  * @param huart           UART handle.
+  * @param WakeUpSelection UART wake up from stop mode parameters.
+  * @retval None
+  */
+static void UARTEx_Wakeup_AddressConfig(UART_HandleTypeDef *huart, UART_WakeUpTypeDef WakeUpSelection)
+{
+  assert_param(IS_UART_ADDRESSLENGTH_DETECT(WakeUpSelection.AddressLength));
+
+  /* Set the USART address length */
+  MODIFY_REG(huart->Instance->CR2, USART_CR2_ADDM7, WakeUpSelection.AddressLength);
+
+  /* Set the USART address node */
+  MODIFY_REG(huart->Instance->CR2, USART_CR2_ADD, ((uint32_t)WakeUpSelection.Address << UART_CR2_ADDRESS_LSB_POS));
+}
+
+/**
+  * @}
+  */
+
+#endif /* HAL_UART_MODULE_ENABLED */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/